In this thesis a Fully-Photonic DRoF (FP-DRoF) system is proposed for deploying of future super-broadband access networks. Digital Radio over Fibre (DRoF) is more independent of the fibre network impairments and the length of fibre than the ARoF link. In order for fully optical deployment of the signal conversion techniques in the FP-DRoF architecture, two key components an Analogue-to-Digital Converter (ADC) and a Digital-to-Analogue Converter (DAC)) for data conversion are designed and their performance are investigated whereas the physical functionality is evaluated. The system simulation results of the proposed pipelined Photonic ADC (PADC) show that the PADC has 10 GHz bandwidth around 60 GHz of sampling rate. Furthermore, by changing the bandwidth of the optical bandpass filter, switching to another band of sampling frequency provides optimised performance condition of the PADC. The PADC has low changes on the Effective Number of Bit (ENOB) response versus analogue RF input from 1 GHz up to 22 GHz for 60 GHz sampling frequency. The proposed 8-Bit pipelined PADC performance in terms of ENOB is evaluated at 60 Gigasample/s which is about 4.1. Recently, different methods have been reported by researchers to implement Photonic DACs (PDACs), but their aim was to convert digital electrical signals to the corresponding analogue signal by assisting the optical techniques. In this thesis, a Binary Weighted PDAC (BW-PDAC) is proposed. In this BW-PDAC, optical digital signals are fully optically converted to an analogue signal. The spurious free dynamic range at the output of the PDAC in a back-to-back deployment of the PADC and the PDAC was 26.6 dBc. For further improvement in the system performance, a 3R (Retiming, Reshaping and Reamplifying) regeneration system is proposed in this thesis. Simulation results show that for an ultrashort RZ pulse with a 5% duty cycle at 65 Gbit/s using the proposed 3R regeneration system on a link reduces rms timing jitter by 90% while the regenerated pulse eye opening height is improved by 65%. Finally, in this thesis the proposed FP-DRoF functionality is evaluated whereas its performance is investigated through a dedicated and shared fibre links. The simulation results show (in the case of low level signal to noise ratio, in comparison with ARoF through a dedicated fibre link) that the FP-DRoF has better BER performance than the ARoF in the order of 10-20. Furthermore, in order to realize a BER about 10-25 for the ARoF, the power penalty is about 4 dBm higher than the FP-DRoF link. The simulation results demonstrate that by considering 0.2 dB/km attenuation of a standard single mode fibre, the dedicated fibre length for the FP-DRoF link can be increased to about 20 km more than the ARoF link. Moreover, for performance assessment of the proposed FP-DRoF in a shared fibre link, the BER of the FP-DRoF link is about 10-10 magnitude less than the ARoF link for -19 dBm launched power into the fibre and the power penalty of the ARoF system is 10 dBm more than the FP-DRoF link. It is significant to increase the fibre link’s length of the FP-DRoF access network using common infrastructure. In addition, the simulation results are demonstrated that the FP-DRoF with non-uniform Wavelength Division Multiplexing (WDM) is more robust against four wave mixing impairment than the conventional WDM technique with uniform wavelength allocation and has better performance in terms of BER. It is clearly verified that the lunched power penalty at CS for DRoF link with uniform WDM techniques is about 2 dB higher than non-uniform WDM technique. Furthermore, uniform WDM method requires more bandwidth than non-uniform scheme which depends on the total number of channels and channels spacing.

Next generation access networks should be able to cultivate the ongoing evolution in services and applications. Advancements on that front are expected to exhibit the transformation of high definition television (HDTV) and 2D services into ultra-HDTV and individual interactive 3D services. Currently deployed passive optical networks (PONs) have been certified to be able to deliver high quality video and internet services while in parallel broadband wireless standards are increasing their spectral efficiency and subscriber utilisation. Exploiting the benefits of both by providing an integrated infrastructure benefiting from the wireless mobility and ease of scalability and escalating bandwidth of next generation PONs are expected to offer service providers the business models justifying the evolved services. In this direction, this thesis deals with the means of transparent routing of standard worldwide interoperability for microwave access (WiMAX) signal formats over legacy PONs to and from wireless end users based on radio over fibre (RoF). The concept of frequency division multiplexing (FDM) with RoF is used for efficient addressing of individual base stations, bandwidth on-demand provisioning across a cell/sector, simple remote radio heads and no interference with the baseband PON spectrum. Network performance evaluation, initially through simulation, has displayed, in the presence of optical non-linearites and multi-path wireless channels, standard error vector magnitudes (EVMs) at remote radio receivers and bit error rates (BERs) of 1E-4 for typical WiMAX rates bidirectionally. To provide enhanced scalability and dynamicity, a newly applied scheme based on extended wavelength band overlay over the splitter, wireless-enabled PONs has been progressively investigated. This allows for the routing of multiple FDM windows to different wavelengths resulting in significantly reduced optical and electrical component costs and no dispersion compensation over the fibre. This has been implemented through the application of a dense array wave guide grating (AWG) and tuneable filter in the optical line terminal (OLT) and optical network unit/base stations (ONU/BSs) respectively. Although with the use of a splitter the distribution point of the optical network remains largely the same, vertical cavity surface emitting laser (VCSEL) arrays provide colourless upstream transmission. In addition, an overlapping cell concept is developed and adopted for increased wireless spectral efficiency and resilience. Finally, an experimental test-bed using commercially available WiMAX transceivers was produced, which enabled repetition of the simulation outcomes and therefore confirmed the overall network performance.

The proliferation of data hungry wireless devices, such as smart phones and intelligent sensing networks, is pushing modern wireless networks to their limits. A significant shortfall in the ability of networks to meet demand for data is imminent. This thesis addresses this problem through examining the design of distributed antenna systems (DAS) to support next generation high speed wireless services that require high densities of access points and must support multiple-input multiple-output (MIMO) protocols. First, it is shown that fibre links in DAS can be replaced with low-cost, broadband free-space optical links, termed radio over free-space optics (RoFSO) links. RoFSO links enable the implementation of very high density DAS without the need for prohibitively expensive cabling infrastructure. A 16m RoFSO link requiring only manual alignment is experimentally demonstrated to provide a spurious-free dynamic range (SFDR) of > 100dB/Hz^2/3 over a frequency range from 300MHz- 3.1GHz. The link is measured to have an 802.11g EVM dynamic range of 36dB. This is the first such demonstration of a low-cost broadband RoFSO system. Following this, the linearity performance of RoFSO links is examined. Because of the high loss nature of RoFSO links, the directly-modulated semiconductor lasers they use are susceptible to high-order nonlinear behaviour, which abruptly limits performance at high powers. Existing measures of dynamic range, such as SFDR, assume only third-order nonlinearity and so become inaccurate in the presence of dominant high-order effects. An alternative measure of dynamic range called dynamic-distortion-free dynamic range (DDFDR) is then proposed. For two different wireless services it is observed experimentally that on average the DDFDR upper limit predicts the EVM knee point to within 1dB, while the third-order SFDR predicts it to within 6dB. This is the first detailed analysis of high-order distortion effects in lossy analogue optical links and DDFDR is the first metric able to usefully quantify such behaviour. Next, the combination of emerging MIMO wireless protocols with existing DAS is examined. It is demonstrated for the first time that for small numbers of MIMO streams (up to ~4), the capacity benefits of MIMO can be attained in existing DAS installations simply by sending the different MIMO spatial streams to spatially separated remote antenna units (RAU). This is in contrast to the prevailing paradigm of replicating each MIMO spatial stream at each RAU. Experimental results for two representative DAS layouts show that replicating spatial streams provides an increase of only ~1% in the median channel capacity over merely distributing them. This compares to a 3-4% increase of both strategies over traditional non-DAS MIMO. This result is shown to hold in the multiple user case with 20 users accessing 3 base stations. It is concluded that existing DAS installations offer negligible capacity penalty for MIMO services for small numbers of spatial streams, including in multi-user MIMO scenarios. Finally, the design of DAS to support emerging wireless protocols, such as 802.11ac, that have large numbers of MIMO streams (4-8) is considered. In such cases, capacity is best enhanced by sending multiple MIMO streams to single remote locations. This is achieved using a novel holographic mode division multiplexing (MDM) system, which sends each separate MIMO stream via a different propagation mode in a multimode fibre. Combined channel measurements over 2km of mode-multiplexed MMF and a typical indoor radio environment show in principle a 2x2 MIMO link providing capacities of 10bit/s/Hz over a bandwidth of 6GHz. Using a second experimental set-up it is shown that the system could feasibly support at least up to a 4x4 MIMO system over 2km of MMF with a condition number >15dB over a bandwidth of 3GHz, indicating a high degree of separability of the channels. Finally, it is shown experimentally that when a fibre contains sharp bends (radius between 20mm and 7.2mm) the first 6 mode-groups used for multiplexing exhibit no additional power loss or cross-coupling compared with unbent fibre, although mode-groups 7, 8 and 9 are more severely affected. This indicates that at least 6x6 multiplexing is possible in standard installations with tight fibre bends.

This thesis investigates the generation and radio-over-fibre (RoF) transport of unlicensed 60 GHz millimetre-wave (mm-wave) frequency band. The investigated benefits of transmission schemes applicable for the mm-wave generation include optical carrier suppression (OCS), optical frequency multiplication (OFM) and remote heterodyne detection (RHD). For the in-door cabling of the mm-wave transmission, a low-cost polymer optical fibre (POF) along with bend-insensitive single mode fibre (BI-SMF) has been investigated for short-range networks. Transporting mm-wave generated signals over POF and BI-SMF cables based on OCS scheme showed results with the highest spectral efficiency and least inter-symbol interference over a 2.5 Gbit/s data delivery. Based on this thesis analysis, OCS simulation of POF showed the most reliable power penalty performance and receiver sensitivity at 30-m whilst the BI-SMF fiber produced equal observations at 150-m and more. In observing the free space links of delivering the RoF signal, the attenuation on the received signal power for both POF and BI-SMF was insignificant but expected, as the simulation assumed complete and total collimation of the light beams onto the aperture of the photodetector. OCS scheme for mm-wave generation and transport was explored based on the cost effectiveness of using one external modulator compared to other generation schemes that utilised more than one external modulator. OFM scheme was simulated to transport LTE and Wi-Fi signals along with 60 GHz RF band through both SMF and MMF-POF/BI-SMF cables. OFM transport scheme produced the highest attenuation on LTE, Wi-Fi and mm-wave signals carrying 100 Mbit/s data as simulated POF lengths increased. The best performance POF length was observed at 10-m. The application of offset launch technique at the coupling of SMF and POF showed insignificant improvement on signal bandwidth. The free space OFM transmission also demonstrated negligible change to the received signal power. This reinforces the attributes of deploying OWC system in an in-door environment. In other investigation, the simulated successful delivery of mm-wave signal using RHD scheme modulated and transported 10 Gbit/s data signal over POF and BI-SMF cables. Additional observed unrecorded result also showed BI-SMF cable maintained a 2% reduction of received power for 450-m fiber cable from 150-m. The attributes to RHD includes its low operating power system application and delivery of localised 60 GHz signal for uplink RoF transmission. The conceptualised design of Gigabit data delivery for indoor customer applications either through POF or BI-SMF cable, transporting various wireless channels has been presented in this thesis for the design of a robust next generation Broadband access network to reinforce the fiber-inside-the-home (FiTH) deployment.

The most important fact in the mobile industry at the moment is that demand for wireless services will continue to expand in the coming years. Therefore, it is vital to find more spectrums through cognitive radios for the growing numbers of services and users. However, the spectrum reallocations, enhanced receivers, shared use, or secondary markets-will not likely, by themselves or in combination, meet the real exponential increases in demand for wireless resources. Network operators will also need to re-examine network architecture, and consider integrating the fibre and wireless networks to address this issue. This thesis involves driving fibre deeper into cognitive networks, deploying microcells connected through fibre infrastructure to the backbone LTE networks, and developing the algorithms for diverting calls between the wireless and fibre systems, introducing new coexistence models, and mobility management. This research addresses the network deployment scenarios to a microcell-aided cognitive network, specifically slicing the spectrum spatially and providing reliable coverage at either tier. The goal of this research is to propose new method of decentralized-to-distributed management techniques that overcomes the spectrum unavailability barrier overhead in ongoing and future deployments of multi-tiered cognitive network architectures. Such adjustments will propose new opportunities in cognitive radio-to-fibre systematic investment strategies. Specific contributions include: 1) Identifying the radio access technologies and radio over fibre solution for cognitive network infrastructure to increase the uplink capacity analysis in two-tier networks. 2) Coexistence of macro and microcells are studied to propose a roadmap for optimising the deployment of cognitive microcells inside LTE macrocells in the case of considering radio over fibre access systems. 3) New method for roaming mobiles moving between microcells and macrocell coverage areas is proposed for managing spectrum handover, operator database, authentication and accounting by introducing the channel assigning agent entity. The ultimate goal is to reduce unnecessary channel adaptations.

Optical fibre has become the dominant theme of transmission in long haul, high data rate communication systems due to its tremendous bandwidth and low loss. Radio over Fibre (RoF) technology facilitates the seamless integration between wireless and optical communication systems and found to be the most promising solution to meet the exponential bandwidth demands expected for the upcoming years. However, the main bit-rate/distance limitation in RoF systems is the chromatic dispersion. In this thesis, the two generations of RoF technologies, namely Analogue RoF (ARoF) and Digital RoF (DRoF) are investigated. The overall aim of this research is to optimise the optical bandwidth utilisation of these two approaches for a typical transmission of the fronthaul link proposed in the next generation Centralised Radio Access Network (C-RAN). Consequently, a number of physical layer design scenarios for the optimised transmission of the Radio Frequency (RF) signals over a Standards Single Mode Fibre (SSMF) are demonstrated. Firstly, for an ARoF transmission, where the analogue RF signals are transported over SSMF using an optical carrier, a bidirectional link transmitting four Downlink/Uplink channels in a chromatic dispersion limited scenario is designed. Simulation results have shown a clear constellation diagram of a 2.5 Gb/s RF signal transmission over 120 km fibre length. Secondly, a DRoF system with reduced optical bandwidth occupancy is proposed. This system employs an optical Duobinary transmission to the digitised RF signal at the transmitter side to reduce its spectrum and to address the chromatic dispersion effect, simultaneously. Simulation results demonstrate the capability of the proposed system to maintain high-quality transmission of the digitised signals over 70 km of fibre distance without dispersion compensation requirements. Finally, an advanced DRoF transmission link based on integrating digital Optical Single Sideband (OSSB) transmission with Duobinary encoding scheme is designed. Simulation results have clearly verified system's robustness against transmission impairments and have better performances in terms of the obtained BER and EVM with respect to the 3GPP standardised values. Moreover, the results show that both transmission distance and power budget are furtherly improved in comparison with two other digital transmission scenarios.

During the last three decades, the significant increase in electricity demand, and its consequences, has appeared as a serious concern for the utility companies, but no major changes have been applied to the conventional power grid infrastructure. Recently, researchers have identified efficient control and power distribution mechanisms as the immediate challenges for conventional power grids. The next step for conventional power grid towards the Smart Grid is to provide energy efficiency management along with higher reliability via smart services, in which the application of Information and Communication Technology (ICT) is inevitable. ICT introduces powerful tools to comply with the smart grid requirements. Among various ICT properties, the telecommunication network plays a key role for providing a secure infrastructure. The two-way digital communication system provides an interaction between energy suppliers and consumers for managing, controlling and optimizing energy distribution. We can also define the smart grid as a two-way flow of energy and control information, where the electricity consumers can generate energy using green energy resources. The main objective of this thesis is to select an effective data communication infrastructure to support the smart grid services by considering a hybrid wireless and optical communication technologies. Radio-over-Fibre (RoF) networks are considered as a potential solution to provide a fast, reliable and efficient network backbone with the optical access network integration and the flexibility and mobility of the wireless network. Therefore, we adopt the integration of RoF to Passive Optical Network (PON) as a broadband access network to transmit smart grid data along with the Fiber to the Home/Building/Curb (FTTx) traffic through the shared fibre, and utilizing Wavelength Division Multiplexing (WDM). Finally, we present and analyze the simulation results for the aforementioned infrastructure based on our enhanced ROF-PON integration model.

En los últimos años ha habido un gran aumento en el despliegue de redes de acceso ópticas de fibra hasta el hogar (FTTH, del inglés fibre-to-the home). FTTH es una solución flexible, una tecnología de acceso de futuro que permite proporcionar tasas de datos del orden de Gbit/s por ususario. Diversos estudios indican que FTTH se convertirá en la diferencia clave entre los operadores más importantes. Además, FTTH es la única tecnolotgía capaz de crear nuevas fuentes de ingresos de aplicaciones de alta velocidad, como por ejemple entretenimiento de alta definición (vído y juegos de alta definición...) Dede el punto de vista del operador, una de las vientajas importantes que proporciona FTTH es que permite una mayor eficiencia operativa en coparción con otras tecnologías de acceso, principalmente por la reducción de costes de mantenimiento y de operación. Además, FTTH reduce los requisitos de los equipos de las centrales. Esta tesis doctoral tiene como ojetivo extender estas ventajas más allá del concepto FTTH mediante la integración de la red óptica de distribución desplegada dentro del hogar así como el enlace radio final de corto o medio alcance inalámbrico. Esto proporciona una arquitctura de red FFTH integrada de extremo a extremo. De este modo, los beneficios de la reducción de costes operativos y mayor eficiencia se extienden hasta el usuario final de la red. En esta tesis doctoral, se propone una arqutectura de acceso integrada óptica-radio basada en la multiplexación por división ortogonal de fecuencia (OFDM, del inglés orthogonal frequency división multiplexing) para proporcionar diferentes servicios al usuario como Internet, teléfono/voz, televisión de lata definición, conexión inalámbrica y seguridad en el hogar. Las señales OFDM se utilizan en muchos estándares inalámbricos como las señales de banda ultraancha (UWB, del inglés ultra-wide band), WiMAX, LTE, WLAN, DVB-T o DAB. Estos formatos aprovechan las características intrínsecas de la modulación OFDM como su mayor inmunidad ante desvanecimiento multi-camino. Esta tesis incluye la propuesta y la demostración experimental de la transmisión simultánea y bi-direccional de señales OFDM multi-estándar en radio-sobre-fibra proporcionando servicios triple-play basados en OFDM como UWB para televisión de alta definición, WiMAX para datos de Internet, y LTE para el servicio telefónico. / Morant Perez, M. (2012). Architectures and Novel Functionalities for Optical Access OFDM Networks "Arquitecturas y Nuevas Funcionalidades para Redes OFDM de Acceso Óptico" [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/15076 / Palancia

La presenta Tesis Doctoral encuentra su ámbito de aplicación en redes de acceso ópticas de fibra hasta el hogar o FTTH (del inglés fibre-to-the-home). Las redes FTTH han sido ampliamente desplegadas en todo el mundo y se prevé que evolucionen hasta arquitecturas de multiplexación por división en longitud de onda o WDM(dle inglés wavelength division multiplexing). Conforme los requerimientos de capacidady ancho de banda por usuario para servicios de comunicación de banda ancha se incrementan continuamente, tecnologías tales como hybrid wireless-optical, radio de banda ultra ancha o UWB(del inglés ultra-wideband), y radio de onda milimétrica se están investigando como soluciones viables para proporcionar tasas de datos excediendo Gigabit por segundo por usuario. Las redes híbridas inalámbrico-óptico pueden proporcionar backhaul más simple y se prevé que desempeñen un papel importante en redes de acceso de próxima generación que requerirán despliegue flexible, alta capacidad, habilidad de ampliación, escalable en número de usuarios y demanda, y factible económicamente. Las técnicas radio sobre fibra combinadas con sistemas inalámbricos multigigabit que proporcionen capacidades comparables a sistemas de comunicaciones de fibra óptica se ve como una solución rápidamente desplegable y efectiva en coste para proporcionar acceso transparente cableado/inalámbrico integrado a servicios de banda ancha para el usuario final. Los sistemas inalámbricos UWB y de onda milimétrica son capaces de proporcionar comunicaciones multigigabit. UWB en particular permite un uso eficiente del esprectro 3.1-10.6 GHz debido a sus características únicas de coexistencia y tiene madurez de mercado. Sin embargo, la tecnología UWB está restringida por regulación en todo el mundo. Esta restricción de regulación hace de gran interés a la radio de onda milimétrica en 60 GHz debido al aproximadamente 7 GHz de ancho de banda regulado consistentemente en todo el mundo, sin restricciones de coexistencia. / Beltrán Ramírez, M. (2012). Photonic Techniques for Next-Generation Integrated Optical Networks Based on Ultra-Wideband Radio / Técnicas Fotónicas para Redes Ópticas Integradas de Próxima Generación Basadas en Radio de Banda Ultra Ancha [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/15576 / Palancia

[pt] Para suportar os requisitos das redes móveis de 5a geração (5G), os sistemas de comunicação óptica serão usados nas redes de acesso. Isso ocorre porque a evolução das RAN (Radio Access Networks) incluem a centralização do equipamento mais crítico para implantar pontos de acesso móveis de baixa potência, como DAS (Distributed Antenna Systems) e Small Cells. Os serviços emergentes solicitam a implantação de tecnologias de rádio sobre fibra com ênfase na eficiência de largura de banda, eficiência energética e alta confiabilidade. Neste âmbito, um monitoramento eficiente da camada física é imperativo para a operação dessas redes. O sistema de monitoramento deve fornecer uma localização de falhas em serviço, econômico, centralizado e com impacto mínimo para a transmissão de dados. Esta tese propõe vários sistemas de monitoramento incorporado no transceptor utilizando reflectometria óptica no domínio do tempo. Os sistemas de monitoramento são testados em diferentes sistemas de transmissão de dados e arquiteturas de rede, onde é apresentada uma validação simulada e outras experimentais. / [en] In order to support the requirements for 5th generation mobile networks (5G), optical communication systems will be used in the access part of the network. This is because the evolution of radio access networks includes the centralization of the most critical equipment in order to deploy low power mobile access points, like distributed antenna systems and small cells. The emerging services call for the deployment of radio over fibre technologies with emphasis on bandwidth efficiency, energy efficiency and high reliability. Within this scope, an efficient monitoring of the physical layer would become essential for the operation of these networks. The monitoring system should provide in-service, cost efficient and centralized fault localization with minimum impact on data transmission. This thesis proposes several transceiver-embedded optical time domain reflectometry monitoring systems. The monitoring systems are tested over different data transmission systems and network architectures, where one architecture was simulated and several others experimentally validated.