Shear layer development over a NACA 0018 airfoil at a chord Reynolds number of 100,000 was investigated experimentally. The effects of experimental setup and analysis tools on the results were also examined. The sensitivity of linear stability predictions for measured separated shear layer velocity profiles to both the analysis approach and experimental data scatter was evaluated. Analysis approaches that are relatively insensitive to experimental data scatter were identified. Stability predictions were shown to be more sensitive to the analysis approach than to experimental data scatter, with differences in the predicted maximum disturbance growth rate and corresponding frequency of approximately 35% between approaches. A parametric study on the effects of experimental setup on low Reynolds number airfoil experiments was completed. It was found that measured lift forces and vortex shedding frequencies were affected by the end plate configuration. It was concluded that the ratio of end plate spacing to projected model height should be at least seven, consistent with the guideline for circular cylinders. Measurements before and after test section wall streamlining revealed errors in lift coefficients due to blockage as high as 9% and errors in the wake vortex shedding frequency of 3.5%. Shear layer development over the model was investigated in detail. Flow visualization images linked an observed asymmetry in wake velocity profiles to pronounced vortex roll-up below the wake centerline. Linear stability predictions based on the mean hot-wire profiles were found to agree with measured disturbance growth rates, wave numbers, and streamwise velocity fluctuation profiles. Embedded surface pressure sensors were shown to provide reasonable estimates of disturbance growth rate, wave number, and convection speed for conditions at which a separation bubble formed on the airfoil surface. Convection speeds of between 30 and 50% of the edge velocity were measured, consistent with phase speed estimates from linear stability theory.

Shear layer development over a NACA 0018 airfoil at a chord Reynolds number of 100,000 was investigated experimentally. The effects of experimental setup and analysis tools on the results were also examined. The sensitivity of linear stability predictions for measured separated shear layer velocity profiles to both the analysis approach and experimental data scatter was evaluated. Analysis approaches that are relatively insensitive to experimental data scatter were identified. Stability predictions were shown to be more sensitive to the analysis approach than to experimental data scatter, with differences in the predicted maximum disturbance growth rate and corresponding frequency of approximately 35% between approaches. A parametric study on the effects of experimental setup on low Reynolds number airfoil experiments was completed. It was found that measured lift forces and vortex shedding frequencies were affected by the end plate configuration. It was concluded that the ratio of end plate spacing to projected model height should be at least seven, consistent with the guideline for circular cylinders. Measurements before and after test section wall streamlining revealed errors in lift coefficients due to blockage as high as 9% and errors in the wake vortex shedding frequency of 3.5%. Shear layer development over the model was investigated in detail. Flow visualization images linked an observed asymmetry in wake velocity profiles to pronounced vortex roll-up below the wake centerline. Linear stability predictions based on the mean hot-wire profiles were found to agree with measured disturbance growth rates, wave numbers, and streamwise velocity fluctuation profiles. Embedded surface pressure sensors were shown to provide reasonable estimates of disturbance growth rate, wave number, and convection speed for conditions at which a separation bubble formed on the airfoil surface. Convection speeds of between 30 and 50% of the edge velocity were measured, consistent with phase speed estimates from linear stability theory.

No description available.

Vortex generator jets (VGJs) have been found to be an effective method of active separation control on the suction side of a low pressure turbine (LPT) blade at low Reynolds numbers. The flow mechanisms responsible for this control were studied and documented in order to provide a basis for future improvements in LPT design. Data were collected using a stereo PIV system that enabled all three components of velocity to be measured. Steady VGJs were injected into a laminar boundary layer on a flat plate (non-separating boundary layer) in order to more fully understand the characteristics and behavior of the produced vortices. Both normal (injected normal to the wall) and angled (injected at 30° pitch and 90° skew angles to the freestream) jets were studied. The steady jets were found to create vortices that swept the low momentum fluid up from the boundary layer while transporting high momentum freestream fluid towards the wall, a phenomenon that provides the ingredients for flow control. Pulsed VGJs were then injected on a flat plate with an applied adverse pressure gradient equivalent to that experienced by a commonly tested LPT blade. This configuration was used to study the effectiveness of the flow control exhibited by both normal and angled jets on a separating boundary layer. Time averaged results showed similar boundary layer separation reduction for both normal and angled jets; however, individual characteristics suggested that the control mechanism of the two injection angles is distinct. Steady and pulsed VGJs were then applied to a new aggressive LPT blade design to explore the effect of the jets on a separating boundary layer along the curved blade surface. Steady injection provided flow control through freestream entrainment, while pulsed jets created a two-dimensional, spanwise disturbance that reduced the separated area as it traveled downstream. A detailed fluid analysis of the uncontrolled flow around the blade was performed in order to identify the separation and reattachment points and the area of transition. This information was used as a basis for comparison with the VGJ cases to determine flow control effectiveness.