Digitized by Kansas State University Libraries

No description available.

No description available.

Thesis (M.S.)--Virginia Polytechnic Institute and State University, 1992. / Vita. Abstract. Includes bibliographical references (leaf 113). Also available via the Internet.

M.Phil. / In today's world with its competitive environment there is a need to shorten product development time by using CFD (Computational Fluid Dynamics) to design an object for example a car, aeroplane or missile and to predict the forces that the wind will have on the object (design). To evaluate the correctness of the CFD results, the design or a scale model of the design must be tested in a wind tunnel by using a force balance. The wind tunnel balance is an apparatus used in the designing and testing of wings, shapes and profiles. In general a balance can be used in all aerodynamic designs to determine the forces on an object when it is moving through air. The aim of this project was to design and manufacture a three-component external balance for a low-speed wind tunnel using an axiomatic design method. It also covers the installation of the external wind tunnel balance to a wind tunnel with a computerized data acquisition capturing system, and performance evaluation of the wind tunnel balance.

Fiber Bragg grating sensors have been constantly researched for the last ten years and have finally begun to find use in the commercial market. However, one of the major factors limiting their widespread use is their system cost. Their lightweight, flexibility, electromagnetic immunity, and small size make fiber Bragg grating (FBG) sensors feasible in hostile environments where electrical and mechanical sensors may not function effectively. These sensor systems utilize moderately expensive light sources and detectors at telecommunication wavelengths of 1300 nm and 1550 nm. These are the center wavelengths of the mass-produced FBGs and FBG phase masks. This thesis addresses the development of a lower cost short wavelength fiber Bragg grating strain sensor system using gratings written at 790 nm and 850 nm with the modified phase mask method recently developed at Oregon State University. Short wavelength gratings allow the use of less expensive semiconductor sources and silicon detectors, greatly reducing the overall cost of a strain sensor system from approximately $1600 for a 1300 nm system to $1000 for a 790 nm system. First, the fundamental properties and historical background of fiber Bragg gratings were reviewed. Followed by a literature review of the structures, fabrication methods, and applications of FBGs including sensor applications. The design, manufacture, and assembly of the new short wavelength strain sensor system were described including the production of pigtailed super-luminescent edge emitting light emitting diodes (SELED) from commercial laser diodes, a fiber recoater, and multiple attempts to write a fiber Bragg grating in the 750-850 nm wavelength region. Finally, the short wavelength strain sensor system was compared with a 1300 nm strain sensor detailing the potential cost savings with the short wavelength system. / Graduation date: 2003

Thesis (Ph. D.)--University of Texas at Austin, 2002. / Vita. Includes bibliographical references. Available also from UMI Company.

Made available in DSpace on 2014-06-11T19:28:34Z (GMT). No. of bitstreams: 0 Previous issue date: 2006-08-11Bitstream added on 2014-06-13T20:37:39Z : No. of bitstreams: 1 resende_fls_me_guara.pdf: 781042 bytes, checksum: 90a752d449437b2098cb5b1a50b2cae7 (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / O objetivo deste trabalho foi estudar a distribuição das cargas no sistema cadeira plataforma de força (C-PF) e verificar se há correlação entre as forças medidas no assento e encosto, na postura sentada adequada. Participaram 38 voluntários, classificados pelo biótipo (32 mulheres e 6 homens): idade média de 43,92 anos, estatura média de 1,60 m e peso corporal médio de 65,10 kgf. Uma cadeira, com células de carga nas partes anterior e posterior do assento e no encosto, e uma plataforma de força mediram a distribuição do peso corporal. Estabeleceram-se várias correlações entre as variáveis (peso corporal, altura, idade, e índice de massa corporal) e as cargas medidas e entre as próprias forças adquiridas. Uma das correlações determinou uma relação entre a força total no assento e a força medida no encosto. A distribuição do peso corporal observada foi: 20,04% na plataforma de força; 45,33% e 30,43%, nas partes anterior e posterior do assento, respectivamente; e 4,20% no encosto. Não houve diferenças estatísticas significativas na comparação das médias dos valores da distribuição do peso corporal tanto entre os sexos como entre os biótipos. Porém, como há diferenças na forma corporal de acordo com os sexos e com os biótipos, houve certa diferença nos valores das forças medidas, no sistema C-PF. / The aim of this study was to study the load distribution in chair-force plate system (CFP) and to verify if there is correlation between measured seat and backrest forces in the adequate sitting posture. 38 volunteers participated of the study, classifieds according to physical types (32 female and 6 male): mean age of 43,92 years old, mean height of 1,60 m and mean body weight of 65,10 kgf. An instrumented office chair with load cells in the anterior and posterior portions of the seat and backrest and a force plate were used to measure the forces and body weight distribution in C-FP system. This study was established many correlations among some variables (body weight, height, age and body mass index) and the measured loads and among the acquired forces. One of these correlations determined a relation among total force measured on seat and acquired force on lumbar backrest. The body weight distribution observed in the C-FP system was: 20,04% in the force plate, 45,33% and 30,43% in the anterior and posterior portions of the seat respectively, and 4,20% in the backrest. There were no statistics significant differences in comparison of values weight distribution averages as between gender as between physical patterns. But, there are some differences in the body shape according to gender and physical patterns, it there was some difference in the values of acquired forces in the C-FP system.

ITC/USA 2005 Conference Proceedings / The Forty-First Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2005 / Riviera Hotel & Convention Center, Las Vegas, Nevada / This paper is about the installation of the instrumentation system and the strain gages on an E-2C Hawkeye for the Advanced Hawkeye Loads Risk Reduction project. Background information on why this project came about will be given. Explanations on why the existing instrumentation system was modified to the current system will be presented. Anthony Cullison (co-author of this paper) will explain the installation of the strain gages.

Tilt and strain meters were installed on the Portland State University campus in the summer of 1982 and data was collected for 4 months. Instrument selection, operation, installation and performance are discussed. Suggestions that could enhance data quality and data collection efficiency are presented. An analysis procedure is suggested and an example of this procedure for an interval of data is discussed. The influence of the temperature, pressure, rainfall and solid earth tides on the signal is investigated, as well as the correlation between similar channels of the different tilt instruments. The temperature, rainfall and solid earth tides were all determined to have an influence on the instruments. A statistical test of the influence of the barometric pressure on the signal revealed no significant influence. A very low correlation between similar components of the different tilt instruments was observed aside from their thermal dependence. It was concluded that in order to obtain high quality data for the use in quantitative calculations, the temperature influence on the raw record must be minimized.