Distributed generation has the potential to reduce the supply-demand gap emerging in New Zealand’s electricity market. Thereby it can improve the overall network efficiency, harness renewable energy resources and reduce the need for upgrading of existing distribution lines. A typical New Zealand rural community consisting of three adjacent farms at Totara Valley near Woodville represents a demonstration site on distributed generation for Massey University and Industrial Research Limited. Local renewable energy resources are being used for the purpose of sustainable development. Alternative micro-scale technologies are being combined to achieve a valuable network support. This paper is an in-depth report on the implementation process of the HyLink system; a system which utilises hydrogen as an energy carrier to balance and transport the fluctuating wind power. The report documents its development from the laboratory stage to commissioning at Totara Valley, which was carried out under direction of Industrial Research Limited. The PEM electrolyser’s performance at different stack temperatures was investigated. It was found that hydrogen production increases at the same voltage with a higher stack temperature. This is due to the improved kinetics of the electrochemical reactions and decreased thermodynamic energy requirement for water electrolysis. The electrolyser efficiency measurement at the half of its maximal power input (247 W) resulted in 65.3%. Thereby the stack temperature attained less than half of the allowed limit of 80°C. The capture of the excess heat by insulation can improve the electrolyser’s efficiency. Pressure tests were performed on the 2 km long pipeline at Totara Valley using hydrogen and natural gas in order to test their permeability. The results were compared with previous studies at Massey University and with data obtained from the industry. The hydrogen permeability was measured to be 5.5 * 10[to the power of]-16 mol m m[to the power of]-2 s[to the power of]-1 Pa[to the power of]-1 for a 2 km MDPE pipe. This is about half the result obtained from previous studies on hydrogen permeability through MDPE at Massey University which was undertaken at room temperature. The reason for this discrepancy is likely to be the lower ambient temperature during the measurement at Totara Valley, which can be supported with the Arrhenius equation. It was furthermore measured that the power loss due to hydrogen diffusion through the pipeline walls during the fuel cell operation is about 1.5 W at the current system operation mode. A techno-economic analysis of the system was undertaken applying the micro-power optimisation software HOMER as a simulation tool. Two operation modes of the system were investigated, the load following and the peak demand compensating. The simulation results reveal that the durability and the cost of the electrochemical energy conversion devices; electrolyser and fuel cell, are the main hurdles which need to be overcome on the path in introducing hydrogen based energy systems like HyLink. Finally, economic optimisation modelling of the small-scale system by best component alignment was performed. It was found that the electrolyser capacity down-rating of 80% in relation to the wind turbine capacity, leads to a minimal system levelised cost. In addition to this, the impact of various wind turbine/electrolyser subsystems and pipeline storage capacities on the fuel cell capacity factor and on the system levelised cost in the load following operation mode was analysed. The outcomes can be useful for further HyLink related energy system planning.

Distributed generation has the potential to reduce the supply-demand gap emerging in New Zealand’s electricity market. Thereby it can improve the overall network efficiency, harness renewable energy resources and reduce the need for upgrading of existing distribution lines. A typical New Zealand rural community consisting of three adjacent farms at Totara Valley near Woodville represents a demonstration site on distributed generation for Massey University and Industrial Research Limited. Local renewable energy resources are being used for the purpose of sustainable development. Alternative micro-scale technologies are being combined to achieve a valuable network support. This paper is an in-depth report on the implementation process of the HyLink system; a system which utilises hydrogen as an energy carrier to balance and transport the fluctuating wind power. The report documents its development from the laboratory stage to commissioning at Totara Valley, which was carried out under direction of Industrial Research Limited. The PEM electrolyser’s performance at different stack temperatures was investigated. It was found that hydrogen production increases at the same voltage with a higher stack temperature. This is due to the improved kinetics of the electrochemical reactions and decreased thermodynamic energy requirement for water electrolysis. The electrolyser efficiency measurement at the half of its maximal power input (247 W) resulted in 65.3%. Thereby the stack temperature attained less than half of the allowed limit of 80°C. The capture of the excess heat by insulation can improve the electrolyser’s efficiency. Pressure tests were performed on the 2 km long pipeline at Totara Valley using hydrogen and natural gas in order to test their permeability. The results were compared with previous studies at Massey University and with data obtained from the industry. The hydrogen permeability was measured to be 5.5 * 10[to the power of]-16 mol m m[to the power of]-2 s[to the power of]-1 Pa[to the power of]-1 for a 2 km MDPE pipe. This is about half the result obtained from previous studies on hydrogen permeability through MDPE at Massey University which was undertaken at room temperature. The reason for this discrepancy is likely to be the lower ambient temperature during the measurement at Totara Valley, which can be supported with the Arrhenius equation. It was furthermore measured that the power loss due to hydrogen diffusion through the pipeline walls during the fuel cell operation is about 1.5 W at the current system operation mode. A techno-economic analysis of the system was undertaken applying the micro-power optimisation software HOMER as a simulation tool. Two operation modes of the system were investigated, the load following and the peak demand compensating. The simulation results reveal that the durability and the cost of the electrochemical energy conversion devices; electrolyser and fuel cell, are the main hurdles which need to be overcome on the path in introducing hydrogen based energy systems like HyLink. Finally, economic optimisation modelling of the small-scale system by best component alignment was performed. It was found that the electrolyser capacity down-rating of 80% in relation to the wind turbine capacity, leads to a minimal system levelised cost. In addition to this, the impact of various wind turbine/electrolyser subsystems and pipeline storage capacities on the fuel cell capacity factor and on the system levelised cost in the load following operation mode was analysed. The outcomes can be useful for further HyLink related energy system planning.

Distributed generation has the potential to reduce the supply-demand gap emerging in New Zealand’s electricity market. Thereby it can improve the overall network efficiency, harness renewable energy resources and reduce the need for upgrading of existing distribution lines. A typical New Zealand rural community consisting of three adjacent farms at Totara Valley near Woodville represents a demonstration site on distributed generation for Massey University and Industrial Research Limited. Local renewable energy resources are being used for the purpose of sustainable development. Alternative micro-scale technologies are being combined to achieve a valuable network support. This paper is an in-depth report on the implementation process of the HyLink system; a system which utilises hydrogen as an energy carrier to balance and transport the fluctuating wind power. The report documents its development from the laboratory stage to commissioning at Totara Valley, which was carried out under direction of Industrial Research Limited. The PEM electrolyser’s performance at different stack temperatures was investigated. It was found that hydrogen production increases at the same voltage with a higher stack temperature. This is due to the improved kinetics of the electrochemical reactions and decreased thermodynamic energy requirement for water electrolysis. The electrolyser efficiency measurement at the half of its maximal power input (247 W) resulted in 65.3%. Thereby the stack temperature attained less than half of the allowed limit of 80°C. The capture of the excess heat by insulation can improve the electrolyser’s efficiency. Pressure tests were performed on the 2 km long pipeline at Totara Valley using hydrogen and natural gas in order to test their permeability. The results were compared with previous studies at Massey University and with data obtained from the industry. The hydrogen permeability was measured to be 5.5 * 10[to the power of]-16 mol m m[to the power of]-2 s[to the power of]-1 Pa[to the power of]-1 for a 2 km MDPE pipe. This is about half the result obtained from previous studies on hydrogen permeability through MDPE at Massey University which was undertaken at room temperature. The reason for this discrepancy is likely to be the lower ambient temperature during the measurement at Totara Valley, which can be supported with the Arrhenius equation. It was furthermore measured that the power loss due to hydrogen diffusion through the pipeline walls during the fuel cell operation is about 1.5 W at the current system operation mode. A techno-economic analysis of the system was undertaken applying the micro-power optimisation software HOMER as a simulation tool. Two operation modes of the system were investigated, the load following and the peak demand compensating. The simulation results reveal that the durability and the cost of the electrochemical energy conversion devices; electrolyser and fuel cell, are the main hurdles which need to be overcome on the path in introducing hydrogen based energy systems like HyLink. Finally, economic optimisation modelling of the small-scale system by best component alignment was performed. It was found that the electrolyser capacity down-rating of 80% in relation to the wind turbine capacity, leads to a minimal system levelised cost. In addition to this, the impact of various wind turbine/electrolyser subsystems and pipeline storage capacities on the fuel cell capacity factor and on the system levelised cost in the load following operation mode was analysed. The outcomes can be useful for further HyLink related energy system planning.

When placed between the antenna and receiver electronics of a cellular base transceiver station, a Cryogenic Receiver Front End (CRFE), consisting of a High Temperature Superconducting (HTS) filter and modern Low Noise Amplifier (LNA), can significantly improve the base stations' coverage and capacity. Due to CRFEs being hurried to the telecommunications industry in a competitive market, the development of CRFEs and their performance have been classified. This left it to be pondered whether HTS filters could really have been beneficial or if they were always just of academic interest. It is the main objective of this thesis to investigate if and under what circumstances high temperature RF-superconductivity can prove to be an important technological contribution to current and future wireless communications. This dissertation presents the analysis of an existing CRFE developed by Cryoelectra GmbH and its performance characteristics measured in a field trial held in rural China. With the aid of a CDMA Uplink Model developed by the author, the data was analysed and several novel engineering improvements were made to create an advanced CRFE which was economical to deploy. The analysis of results from a field trial in Beijing city using the CDMA Uplink Model led to the exploration of alternative filter technologies which could achieve similar results to the HTS filter technology. This culminated in the development of dielectric resonators filters which could be used as an alternative and as a supplement to the HTS filters used in the CRFE. The design of two novel dielectric resonator duplexers and two advanced multioperator combiner antenna sharing solutions followed the successful implementation of a high performance dielectric resonator filter. The performed investigation and development described in this thesis suggest that HTS filter technology for terrestrial wireless communications can be beneficial in current cellular networks, but due to its high cost is economical for use only under certain conditions. However, HTS filter technology may be of great importance in the design and implementation of spectrum friendly wireless communications systems in the future.

Multipath propagation and mobility in wireless communication systems give rise to variations in the amplitude and phase of the transmitted signal, commonly referred to as fading. Many wireless applications are affected by slowly varying fading, where the channel is non-ergodic, leading to non-reliable transmission during bad channel realizations. These communication scenarios are well modeled by the block-fading channel, where the reliability is quantatively characterized by the outage probability. This thesis focuses on the analysis and design of adaptive transmission schemes to improve the outage performance of both single- and multiple-antenna transmission over the block-fading channel, especially for the cases where discrete input constellations are used. Firstly, a new lower bound on the outage probability of non-adaptive transmission is proposed, providing an efficient tool for evaluating the performance of non-adaptive transmission. The lower bound, together with its asymptotic analysis, is essential for efficiently designing the adaptive transmission schemes considered in the thesis. Secondly, new power allocation rules are derived to minimize the outage probability of fixed-rate transmission over block-fading channels. Asymptotic outage analysis for the resulting schemes is performed, revealing important system design criteria. Furthermore, the thesis proposes novel suboptimal power allocation rules, which enjoy low-complexity while suffering minimal losses as compared to the optimal solution. Thus, these schemes facilitate power adaptation in low-cost devices. Thirdly, the thesis considers incremental-redundancy automatic-repeat-request (INR-ARQ) strategies, which perform adaptive transmission based on receiver feedback. In particular, the thesis concentrates on multi-bit feedback, which has been shown to yield significant gains in performance compared to conventional single-bit ARQ schemes. The thesis proposes a new information-theoretic framework for multi-bit feedback INR-ARQ, whereby the receiver feeds back a quantized version of the accumulated mutual information. Within this framework, the thesis presents an asymptotic analysis which yields the large gains in outage performance offered by multi-bit feedback. Furthermore, the thesis proposes practical design rules, which further illustrates the benefits of multi-bit feedback in INR-ARQ systems. In short, the thesis studies the outage performance of transmission over block-fading channels. Outage analysis is performed for non-adaptive and adaptive transmission. Improvements for the existing adaptive schemes are also proposed, leading to either lower complexity requirements or better outage performance. Still, further research is needed to bring the benefits offered by adaptive transmission into practical systems. / Thesis (PhD)--University of South Australia, 2010

Opportunistic communication techniques have shown to provide significant performance improvements in centralised random access wireless networks. The key mechanism of opportunistic communication is to send back-to-back data packets whenever the channel quality is deemed "good". Recently there have been attempts to introduce opportunistic communication techniques in distributed wireless networks such as wireless ad hoc networks. In line of this research, we propose a new paradigm of medium access control, called Channel MAC based on the channel randomness and opportunistic communication principles. Scheduling in Channel MAC depends on the instance at which the channel quality improves beyond a threshold, while neighbouring nodes are deemed to be silent. Once a node starts transmitting, it will keep transmitting until the channel becomes "bad". We derive an analytical throughput equation of the proposed MAC in a multiple access environment and validate it by simulations. It is observed that Channel MAC outperforms IEEE 802.11 for all probabilities of good channel condition and all numbers of nodes. For higher number of nodes, Channel MAC achieves higher throughput at lower probabilities of good channel condition increasing the operating range. Furthermore, the total throughput of the network grows with increasing number of nodes considering negligible propagation delay in the network. A scalable channel prediction scheme is required to implement the practical Channel MAC protocol in practice. We propose a mean-value based channel prediction scheme, which provides prediction with enough accuracy to be used in the Channel MAC protocol. NS2 simulation result shows that the Channel MAC protocol outperforms the IEEE 802.11 in throughput due to its channel diversity mechanism in spite of the prediction errors and packet collisions. Next, we extend the Channel MAC protocol to support multi-rate communications. At present, two prominent multi-rate mechanisms, Opportunistic Auto Rate (OAR) and Receiver Based Auto Rate (RBAR) are unable to adapt to short term changes in channel conditions during transmission as well as to use optimum power and throughput during packet transmissions. On the other hand, using channel predictions, each source-destinations pair in Channel MAC can fully utilise the non-fade durations. We combine the scheduling of Channel MAC and the rate adaptive transmission based on the channel state information to design the 'Rate Adaptive Channel MAC' protocol. However, to implement the Rate adaptive Channel MAC, we need to use a channel prediction scheme to identify transmission opportunities as well as auto rate adaptation mechanism to select rates and number of packets to transmit during those times. For channel prediction, we apply the scheme proposed for the practical implementation of Channel MAC. We propose a "safety margin" based technique to provide auto rate adaptation. Simulation results show that a significant performance improvement can be achieved by Rate adaptive Channel MAC as compared to existing rate adaptive protocols such as OAR.

Opportunistic communication techniques have shown to provide significant performance improvements in centralised random access wireless networks. The key mechanism of opportunistic communication is to send back-to-back data packets whenever the channel quality is deemed "good". Recently there have been attempts to introduce opportunistic communication techniques in distributed wireless networks such as wireless ad hoc networks. In line of this research, we propose a new paradigm of medium access control, called Channel MAC based on the channel randomness and opportunistic communication principles. Scheduling in Channel MAC depends on the instance at which the channel quality improves beyond a threshold, while neighbouring nodes are deemed to be silent. Once a node starts transmitting, it will keep transmitting until the channel becomes "bad". We derive an analytical throughput equation of the proposed MAC in a multiple access environment and validate it by simulations. It is observed that Channel MAC outperforms IEEE 802.11 for all probabilities of good channel condition and all numbers of nodes. For higher number of nodes, Channel MAC achieves higher throughput at lower probabilities of good channel condition increasing the operating range. Furthermore, the total throughput of the network grows with increasing number of nodes considering negligible propagation delay in the network. A scalable channel prediction scheme is required to implement the practical Channel MAC protocol in practice. We propose a mean-value based channel prediction scheme, which provides prediction with enough accuracy to be used in the Channel MAC protocol. NS2 simulation result shows that the Channel MAC protocol outperforms the IEEE 802.11 in throughput due to its channel diversity mechanism in spite of the prediction errors and packet collisions. Next, we extend the Channel MAC protocol to support multi-rate communications. At present, two prominent multi-rate mechanisms, Opportunistic Auto Rate (OAR) and Receiver Based Auto Rate (RBAR) are unable to adapt to short term changes in channel conditions during transmission as well as to use optimum power and throughput during packet transmissions. On the other hand, using channel predictions, each source-destinations pair in Channel MAC can fully utilise the non-fade durations. We combine the scheduling of Channel MAC and the rate adaptive transmission based on the channel state information to design the 'Rate Adaptive Channel MAC' protocol. However, to implement the Rate adaptive Channel MAC, we need to use a channel prediction scheme to identify transmission opportunities as well as auto rate adaptation mechanism to select rates and number of packets to transmit during those times. For channel prediction, we apply the scheme proposed for the practical implementation of Channel MAC. We propose a "safety margin" based technique to provide auto rate adaptation. Simulation results show that a significant performance improvement can be achieved by Rate adaptive Channel MAC as compared to existing rate adaptive protocols such as OAR.

Multipath propagation and mobility in wireless communication systems give rise to variations in the amplitude and phase of the transmitted signal, commonly referred to as fading. Many wireless applications are affected by slowly varying fading, where the channel is non-ergodic, leading to non-reliable transmission during bad channel realizations. These communication scenarios are well modeled by the block-fading channel, where the reliability is quantatively characterized by the outage probability. This thesis focuses on the analysis and design of adaptive transmission schemes to improve the outage performance of both single- and multiple-antenna transmission over the block-fading channel, especially for the cases where discrete input constellations are used. Firstly, a new lower bound on the outage probability of non-adaptive transmission is proposed, providing an efficient tool for evaluating the performance of non-adaptive transmission. The lower bound, together with its asymptotic analysis, is essential for efficiently designing the adaptive transmission schemes considered in the thesis. Secondly, new power allocation rules are derived to minimize the outage probability of fixed-rate transmission over block-fading channels. Asymptotic outage analysis for the resulting schemes is performed, revealing important system design criteria. Furthermore, the thesis proposes novel suboptimal power allocation rules, which enjoy low-complexity while suffering minimal losses as compared to the optimal solution. Thus, these schemes facilitate power adaptation in low-cost devices. Thirdly, the thesis considers incremental-redundancy automatic-repeat-request (INR-ARQ) strategies, which perform adaptive transmission based on receiver feedback. In particular, the thesis concentrates on multi-bit feedback, which has been shown to yield significant gains in performance compared to conventional single-bit ARQ schemes. The thesis proposes a new information-theoretic framework for multi-bit feedback INR-ARQ, whereby the receiver feeds back a quantized version of the accumulated mutual information. Within this framework, the thesis presents an asymptotic analysis which yields the large gains in outage performance offered by multi-bit feedback. Furthermore, the thesis proposes practical design rules, which further illustrates the benefits of multi-bit feedback in INR-ARQ systems. In short, the thesis studies the outage performance of transmission over block-fading channels. Outage analysis is performed for non-adaptive and adaptive transmission. Improvements for the existing adaptive schemes are also proposed, leading to either lower complexity requirements or better outage performance. Still, further research is needed to bring the benefits offered by adaptive transmission into practical systems. / Thesis (PhD)--University of South Australia, 2010