No abstract available

The growth of interactive multimedia (IMM) applications is one of the major driving forces behind the swift evolution of next-generation wireless networks where the traffic is expected to be varying and widely diversified. The amalgamation of multimedia applications on high-speed wireless networks is somewhat a natural evolution. Wireless local area network (WLAN) was initially developed to carry non-real time data. Since this type of traffic is bursty in nature, the channel access schemes were based on contention. However real time traffic (e.g. voice, video and other IMM applications) are different from this traditional data traffic as they have stringent constraints on quality of service (QoS) metrics like delay, jitter and throughput. Employing contention free channel access schemes that are implemented on the point coordination function (PCF), as opposed to the numerous works on the contending access schemes, is the plausible and intuitive approach to accommodate these innate requirements. Published researches show that works have been done on improving the distributed coordination function (DCF) to handle IMM traffic. Since the WLAN traffic today is a mix of both, it is only natural to utilize both, DCF and PCF, in a balanced manner to leverage the inherent strengths of each of them. We saw a scope in this technique and develop a scheme that combines both contention and non-contention based phases to handle heterogeneous traffic in WLAN. Standard access scheme, like 802.11e, improves DCF functionality by trying to emulate the functions of PCF. Researchers have made a multitude of improvements on 802.11e to reduce the costs of implementing the scheme on WLAN. We explore improving the PCF, instead, as this is more stable and implementations would be less costly. The initial part of this research investigates the effectiveness of the point coordination function (PCF) for carrying interactive multimedia traffic in WLAN. The performance statistics of IMM traffic were gathered and analyzed. Our results showed that PCF-based setup for IMM traffic is most suitable for high load scenarios. We confirmed that there is a scope in improving IMM transmissions on WLAN by using the PCF. This is supported by published researches on PCF related schemes in carrying IMM traffic on WLAN. Further investigations, via simulations, revealed that partitioning the superframe (SF) duration according to the need of the IMM traffic has considerable impact on the QoS of the WLAN. A theoretical model has been developed to model the two phases, i.e., PCF and DCF, of WLAN medium access control (MAC). With this model an optimum value of the contention free period (CFP) was calculated to meet the QoS requirement of IMM traffic being transmitted. Treating IMM traffic as data traffic or equating both IMM and non-IMM together could compromise a fair treatment that should be given to these QoS sensitive traffic. A self-adaptive scheme, called MAC with Dynamic Superframe Selection (MDSS) scheme, generates an optimum SF configuration according to the QoS requirements of traversing IMM traffic. That particular scheme is shown to provide a more efficient transmission on WLAN. MDSS maximizes the utilization of CFP while providing fairness to contention period (CP). The performance of MDSS is compared to that of 802.11e, which is taken as the benchmark for comparison. Jitter and delay result for MDSS is relatively lower while throughput is higher. This confirms that MDSS is capable of making significant improvement to the standard access scheme.

The quality of Machine Translation (MT) can often be poor due to it appearing incoherent and lacking in fluency. These problems consist of word ordering, awkward use of words and grammar, and translating text too literally. However we should not consider translations such as these failures until we have done our best to enhance their quality, or more simply, their fluency. In the same way various processes can be applied to touch up a photograph, various processes can also be applied to touch up a translation. This research outlines the improvement of MT quality through the application of Fluency Enhancement (FE), which is a process we have created that reforms and evaluates text to enhance its fluency. We have tested our FE process on our own MT system which operates on what we call the SAM fundamentals, which are as follows: Simplicity - to be simple in design in order to be portable across different languages pairs, Adaptability - to compensate for the evolution of language, and Multiplicity - to determine a final set of translations from as many candidate translations as possible. Based on our research, the SAM fundamentals are the key to developing a successful MT system, and are what have piloted the success of our FE process.

In today’s technological world, electrical energy is one of the most important forms of energy and is needed directly or indirectly in almost every field. Increase in the demand and consumption of electrical energy leads to increase in the system fault levels. It is not possible to change the rating of the equipment and devices in the system or circuits to accommodate the increasing fault currents. The devices in electronic and electrical circuits are sensitive to disturbance and any disturbance or fault may damage the device permanently so that it must be replaced. The cost of equipment like circuit breakers and transformers in power grids is very expensive. Moreover, replacing damaged equipment is a time and labour consuming process, which also affects the reliability of power systems. It is not possible to completely eliminate the faults but it is possible to limit the current during fault in order to save the equipment and devices in the circuits or systems. One solution to this problem is to use a current limiting device in the system. There are many different types of approaches used for limiting fault currents Two different approaches to limit fault currents have been discussed by the author. One is Passive Magnetic Current Limiter (MCL) and another is High Temperature Superconductor Fault Current Limiter (HTSFCL). Both are passive devices and they do not need any sensor or external sources to perform their current limiting action. The first device consists of two ferrite cores and a permanent magnet which is sandwiched between the two saturated cores and it is called Magnetic Current Limiter. Experimental results with the MCL in circuit are discussed. Both field and thermal models of the MCL have been simulated using finite element software, FEMLAB. The demonstration of the High Temperature Superconductor Fault Current Limiter (HTSFCL) in power systems has been explained. The MATLAB simulation of the HTSFCL has been done and the results with and without the fault are shown. Power System Analysis Toolbox (PSAT) software has been used to locate the optimum or the best location of HTSFCL in a nine bus system. It has been shown that it is possible to find a solution that limits the fault current in power systems. Depending on the size of the system, either the MCL or the HTSFCL can be implemented. The location of the HTSFCL is to be carefully selected to achieve optimum results.

This Master of Design study aims to communicate affective design principles within a Tait Electronics Ltd hand-held radio for the New Zealand Police to use in the year 2018. This investigation has three distinct research aims: A) Identify affective design principles appropriate for the design of current Tait portable police radios using the perceptual product experience (PPE) framework (Warell, 2008). B) Use speculative scenario planning to develop an understanding of how the requirements of Tait’s portable police radios will evolve over the next 10 years. C) Incorporate affective design principles and the brand values of Tait’s product range into a final conceptual portable police radio design for the year 2018. A comprehensive review of contemporary affective product design theory, case studies and other relevant literature was undertaken. This included affective product design (Warell, 2008), radio communication (Marzano, 2005) and future product forecasting (Lambourne, Feiz, & Rigot, 1997). Following this review the following research methods were selected for this study: 1) Future scenario planning 2) Current product-user interviews 3) Passive product observations Throughout the project iterative design methods were used, including 2D concept generation, concept development and 3D prototyping. The resulting conceptual product and associated documentation of this study will add to the existing body of knowledge around the application of affective design principles and portable police radio product design. Keywords: radio, NZ Police, usability, performance, experience, perceptual product experience (PPE), affective product design