Doctor of Philosophy / Department of Agronomy / Phillip W. Stahlman / Saflufenacil is an experimental herbicide for control of broadleaf weeds in various crops including several herbicide resistant weed biotypes. Wheat is highly tolerant to preplant and preemergence applications of saflufenacil, but winter wheat growers prefer to apply herbicides postemergence (POST) in early spring. Objectives of this research were to (1) evaluate winter wheat and four common broadleaf weed species response to POST treatments of saflufenacil applied alone and in combination with bentazon or auxin herbicides at various rates both with and without adjuvants, and to (2) determine the possible mechanism(s) responsible for crop safening observed when saflufenacil is applied with 2,4-D amine or bentazon in winter wheat. Growth chamber, greenhouse, and field studies showed saflufenacil at a minimum rate of 25 g/ha controlled blue mustard and flixweed >85% when saflufenacil was applied alone or mixed with dicamba, 2,4-D amine, 2,4-D ester, or MCPA ester. Also, mixtures of bentazon with 13 g/ha of saflufenacil resulted in death of kochia, but increasingly higher rates of 2,4-D amine were needed to achieve 90% growth reduction when saflufenacil rates were decreased from 50 to 25 to 13 g/ha. In general, most of the saflufenacil combinations tested controlled henbit <85%. Leaf necrosis and stunting of winter wheat were reduced by tank mixing saflufenacil with dicamba, 2,4-D amine, or bentazon, but not with MCPA ester or 2,4-D ester. Including nonionic surfactant (NIS) in mixtures of saflufenacil plus 2,4-D amine resulted in significant wheat injury similar or greater than injury caused by saflufenacil plus NIS. Finally, 2,4-D amine enhanced saflufenacil absorption into winter wheat plants, whereas bentazon reduced absorption of saflufenacil. No more than 11% of applied saflufenacil translocated out of treated leaves to other plant parts when applied alone or when saflufenacil was mixed with 2,4-D amine or bentazon. Metabolism of saflufenacil by wheat plants was not affected by tank mixing with bentazon, but saflufenacil metabolism was slowed by mixing with 2,4-D amine. Overall, these studies indicate saflufenacil can potentially be used POST in wheat at an optimum rate of 25 g/ha plus 2,4-D amine or dicamba to effectively control blue mustard and flixweed.

Investigations on post service material showed that Alloy 800H pigtails from methanol producer Methanex have service lives ranging from 3 to 18 years. Because of this variability in service life, Alloy 800H creep performance was assessed and a new criterion for its procurement developed. The current criterion recommends an ASTM grain size of 5 (72µm) or coarser with no consideration given to grain size distribution, grain boundary types, or grain boundary network topology. Results from the investigation showed that this current criterion may produce variations in steady state creep rates of an order of magnitude between ASTM grain size 1 and 5, and a 2.5 times variation in creep ductility. The ability to accurately reveal grain boundaries and assess grain boundary types is fundamental to the identification and quantification of coherent twin boundaries, and the measurement of average grain size and grain size distribution. EBSD mapping has the ability to distinguish grain boundary types using crystal orientation measurement. Grain size measurement from optical micrographs relies on morphological indicators to identify coherent twins. However, it is shown that many of the boundaries observed as straight line morphology on 2D sections did not possess {111} (coherent) interfaces. 3D reconstructions of Alloy 800H revealed the deficiencies in classifying geometry from two-dimensional (2D) sections. Σ3 Crystal volumes can be categorized as lamellar or edge structures. Lamellar structures are characterized by the appearance of parallel Σ3 boundary planes while an edge structure contains a single Σ3 interface. Sectioning plane location alters the perception of morphology. For simple twin structures, the tradition 2D classifications of morphology (complete parallel, incomplete parallel and corner Σ3) may all appear on a section plane from a single lamellar structure.

Fuel cladding is one of the most critical components of nuclear reactors; so it is important to improve our understanding of various properties and behaviors of the cladding under different conditions approximating the nuclear reactor environment. Moreover, the efficiency of energy production, in addition to safety concerns, has resulted in progressive improvement of nuclear reactors design from Generation I to Generation IV. To complement this progressive trend, materials used for fuel cladding need to be improved or new materials should be developed. In this thesis, I address problems in the improvement of present fuel cladding and also investigate fuel cladding materials to be used in future Generation IV nuclear reactors. In the case of current Zircaloy-4 fuel claddings, a detailed evaluation of the surface roughness effects on their performance and properties of Zircaloy-4 fuel claddings was studied. A smoother surface on Zircaloy-4 cladding tubes is demanded by the customers; however no systematic study is available addressing the effect of surface roughness on the claddings’ performance. Thus the effects of surface roughness on texture, oxidation, hydriding behaviors and mechanical properties of Zircaloy-4 cladding tubes were investigated using various methods. It was found that surface roughness has some effects on the oxidation of Zircaloy-4. Increasing the surface roughness would increase the weight gain, however, this effect was more pronounced at the initial oxidation stages. Synchrotron techniques were used to characterize the electronic structure of zirconium alloys in their oxidized and hydrided states. With this approach, complex interactions between hydrogen and oxygen in the zirconium matrix could be investigated, which could not be resolved using conventional methods. As a candidate for future fuel cladding material, Incoloy 800H/HT, which is expected to be considered in super-critical water-cooled Gen IV reactors, was studied in order to optimize microstructure, texture and grain boundary characteristics. A specific Thermo-Mechanical Processing (TMP) was employed to manipulate the texture, microstructure and grain boundary character distribution. The deformation and annealing textures of thermo-mechanically processed samples were investigated by means of X-ray diffraction and orientation imaging microscopy. It was found that different rolling paths lead to different textures. The origin of different textures in differently (unidirectional and cross) rolled Incoloy 800H/HT at high deformation strains were investigated. In addition, the recrystallization kinetic of differently rolled samples was studied. It was found that the oriented nucleation plays an important role in determining the recrystallization texture. Unidirectional rolled samples exhibited a faster recrystallization kinetic compared with cross rolled ones, due to the presence of γ-fibre. The effect of the aforementioned microstructural parameters (grain size, texture and GBCD) on the oxidation resistance of Incoloy 800H/HT in super-critical water was investigated. It was found that the oxidation resistance of Incoloy 800H/HT can be improved by TMP. The optimum TMP process for enhancing the oxidation resistance was proposed. Microstructural parameters that can improve the oxidation resistance of Incoloy 800H/HT were identified. These findings will contribute to the effective selection of fuel cladding material for application in Gen IV SCW reactors.