In response to the development of a next-generation networking (NGN), generalized multi-protocol label switching (GMPLS) technology is required for automatically switched optical network (ASON). Reconfigurable optical add-drop multiplexer (ROADM) is an indispensable device for the ASON, and the dense wavelength division multiplexed (DWDM) signals can be transmitted through the network under the management of the network administrator to configure dynamic customer needs and the desired quality of service (QoS). The ROADM can also increase the efficiency of utilizing the existing capacity of the optical fiber lines and can reduce or waive to set up additional optical fiber lines. This thesis studies a ROADM based on the arrayed waveguide grating (AWG) and the fiber Bragg grating (FBG) to overcome the issue that the current ROADM cannot process input signal channels that is greater than the wavelength channels of the AWG. All kinds of ROADM have been proposed and realized through different optical devices. Among these, hybrid optical circulator and FBG based ROADM is more attractive because of its low crosstalk and polarization insensitivity. However, in the previous study, the structure needs an optical circulator and a fiber Bragg grating per wavelength. If there are 10 wavelengths to be used, you need 10 groups of the optical circulator and the fiber Bragg grating corresponding to each wavelength. This situation not only increases the number of components, but also increases the insertion loss of the system. In this master thesis, we focus on to reduce number of circulators and gratings while obtaining the best results. At the same time we think about whether this structure is the best, and thus try to change the asymmetrical architecture to compare. The final results show that the asymmetrical structure is better, but it does not realize optical cross-connect (OXC). Therefore for the choice, we must choose the best results or the exchangeability of the symmetrical structure.

No description available.

In recent years, several studies and simulations have been made on changing the current Radio Access Network (RAN) architecture into a more centralized access network where the base band processing is done in a central oce (CO) instead of out by the antenna site. This new architecture is denoted as the mobile fronthaul and is planned to be in use for the coming 5G network. The studies that have been made so far suggest that the new architecture can reduce cost, power usage and latency which are important factors regarding environmental, economical and data transmission issues. Furthermore, the new architecture allows a smarter distribution of data for each sector covered by the antennas, reducing redundant data transmission and thus increases the data eciency. The disadvantage or challenge however is that some of the optical components will be transferred from the currently controlled environment in the CO to an uncontrolled outdoor environment at the antenna site, which may generate risks as these components may be sensitive to especially changes in temperature. In this master thesis, the optical performance of four di erent passive lter setups, using a thin lm lter (TFF), an arrayed waveguide grating (AWG) and an interleaver, has been studied and compared in order to nd the most suitable lter setup for the mobile fronthaul. These optical parameters include insertion loss, isolation, crosstalk, 3 dB passband, center wavelength drift and also bit error-rate (BER) which have all been measured over a temperature interval of -40-85oC. Moreover, the measurement results have been compared with results from simulations done with VPItransmissionmaker. From the measurement results, the TFF had a better optical performance and reliability compared to the AWG mainly due to a higher isolation and a lower BER penalty of 0.2 dB compared to 0.5-1.5 dB for the AWG. Considering data capacity and economical aspects for a more realistic mobile fronthaul scenario with 80 channels using dense wavelength division multiplexing (DWDM) however, the AWG connected to the interleaver is more benecial without risking negative a ects on trac performance. / Under senare år har flera studier och simulationer utförts med syfte att ändra arkitekturen på dagens radioaccess-nätverk till ett mer centraliserat nätverk där basbandsprocesseringen sker i en central nod istället för ute vid antennen och radiomasterna. Denna nya arkitektur kallas mobile fronthaul och planeras att realiseras till 5G-nätet. De studier som har gjorts hittills indikerar på att den nya arkitekturen kan minska ekonomiska kostnader, elanvändningen och latens vilka är viktiga faktorer som bland annat rör miljö-, ekonomi och kapacitetrelaterade områden. Dessutom kan data fördelas på ett smartare sätt över alla delområden som antennerna täcker vilket minskar redundant datatrafik och därmed ökar den effektiva mängden data som skickas ut. Problemet eller utmaningen är att vissa optiska komponenter behöver flyttas från en nuvarande kontrollerad miljö till en okontrollerad utemiljö vid radiomasterna vilket kan medföra risker då dessa komponenter främst kan vara väldigt temperaturkänsliga. Inom detta examensarbete har optisk prestanda studerats, analyserats och jämförts mellan fyra olika filterkonstellationer bestående av ett tunnfilmsfilter, ett AWG-filter och en interleaver med syfte att finna vilken konstellation som passar bäst för mobile fronthaularkitekturen. De optiska parametrarna består av insertionsförluster, isolation, överhörningsinterferens, 3 dB-passband, centervåglängdsdrift samt bitfelsgrad vilka alla har blivit undersökta över ett temperaturintervall på -40-85oC. Utöver detta så har mätresultaten jämförts med simulationer gjorda med VPItransmissionmaker. Utifrån mätresultaten kunde det konstateras att tunnfilmfiltret hade bättre optiska egenskaper och även högre trovärdighet jämfört med AWG-filtret främst på grund av en högre isolation och lägre bitfelsgradsstraff på 0.2 dB jämfört med 0.5-1.5 dB för AWG-filtret. Om en endast avväger datakapacitet och ekonomiska aspekter för ett mer realistiskt scenario för mobile fronthaul med 80 DWDM-kanaler så är AWG-filtret tillsammans med interleavern mer foördelaktig att välja utan att riskera några negativa påverkningar på trafikprestandan.

The characteristics of a silicon-on-insulator (SOI) rib waveguide, including the bending loss of a multimode bent waveguide and the birefringence of a rib waveguide, are analyzed by using a finite-difference method (FDM). Based on a detailed analysis for a multimode bent waveguide, an appropriately designed multimode bent waveguide for reducing effectively the bending loss of the fundamental mode is realized. The slab height and the rib width of an SOI rib waveguide are normalized with the total height of the silicon layer and a general relation between these two normalized parameters for a nonbirefringent SOI rib waveguide is established. Using this general relation, one can easily design a nonbirefringent SOI rib waveguide. The issue of multimode effect in the SOI-based microphotonic devices such as arrayed-waveguide gratings (AWGs), etched diffraction gratings (EDGs), and multimode interference (MMI) couplers is discussed in detail. Two kinds of taper structures are proposed for reducing the multimode effects in EDGs or MMI couplers. A bi-level taper is introduced to eliminate effectively the multimode effects in an EDG or an MMI coupler. The bi-level taper is very appropriate for an EDG demultiplexer since the Si layer is etched through simultaneously for both the grating and the bottom taper structure, and thus no additional fabrication process is required. For the simulation of an AWG demultiplexer, a fast simulation method based on the Gaussian approximation is proposed and two kinds of effective and accurate three-dimensional (3D) simulation modeling are developed. The first 3D model is based on Kirchhoff-Huygens diffraction formula. To improve the computational speed, the 3D model is reduced to a two-dimensional (2D) one by integrating the corresponding field distributions in the AWG demultiplexer along the vertical direction under an assumption that the power coupled to the higher order modes in the free propagation region (FPR) is negligibly small. The equivalent 2D model has an almost the same accuracy as the original 3D model. Furthermore, a reciprocity theory is introduced for the optimal designof a special structure used for flattening the spectral response of an AWG demultiplexer. In the second 3D simulation method, we combine a beam propagation method (BPM) and the Kirchhoff-Huygens diffraction formula. In this method, a 3D BPM in a polar coordinate system is used for calculating the light propagation in the region connecting the first FPR and the arrayed waveguides, and thus the coupling coefficient of each arrayed waveguide is calculated conveniently and accurately. In the simulation of the second FPR, due to the uniform arrangement of arrayed waveguides, only several arrayed waveguides are needed in the BPM window and thus the computational efficiency is improved. / QC 20101004

No description available.

The work deals with optical access networks, passive optical networks, especially WDM-PON. Features a modern solution to connect users to the optical access network using optical FTTx connections. Describes the different types of FTTx connections, their parameters and construction technology. Practical work is a practical application of theory for the development of various design and simulation of WDM-PON networks. Each proposal includes the construction of technical solutions optical access networks, the technology used and the balance of the reduced pricing WDM-PON network. The penultimate part of the work consists of design models simulated WDM-PON networks by the simulation program OptSim. The conclusion deals with the evaluation of individual design and simulation of WDM-PON networks.

No description available.

Les travaux portent sur les multiplexeurs optiques fonctionnant à mi-IR pour la source à large bande dans l'application de détection de gaz. Deux configurations ont été étudiées: réseau de guides d'onde (AWG) et réseau concave planaire (PCG). Premièrement, le principe du fonctionnement a été compris afin de développer une solution analytique pour le champ de sortie en utilisant une approximation gaussienne du champ et de l'optique de Fourier. Ensuite, un outil de simulation semi-analytique de la réponse spectrale pour les deux configurations de multiplexeur a été développé dans MATLAB. La distribution normale des erreurs de phase a été introduite dans le modèle semi-analytique AWG, ce qui nous a permis d'étudier la corrélation entre l'écart-type des erreurs de phase et le niveau de diaphonie de la réponse spectrale AWG. AWG à 5,65 μm a été fabriqué à partir de la technologie SiGe / Si à l'aide de l'outil MATLAB pour le calcul des paramètres de conception et de l'outil P.Labeye pour le calcul de la géométrie AWG. Les dispositifs avec des paramètres légèrement variables ont été caractérisés: AWG1 avec guides d'ondes de 4,6 μm et MMI de 9 μm; AWG2 avec guides d'ondes de 4,6 μm et MMI de 11 μm; AWG3 avec guides d'ondes de 4,8 μm et MMI de 9 μm. Des mesures des dispositifs sur la puce 36 (centre de la plaquette) et sur la puce 32 (côté de la plaquette) ont été effectuées et analysées. Les mesures de température de AWG2 et AWG3 (puce 32 et puce 36) aux points cinq points de température ont montré une dépendance linéaire du déplacement spectral avec la température qui a une bonne corrélation avec les prédictions de simulation. / The work focuses on optical multiplexers operating in mid-IR for broadband source in gas sensing application. Two configurations were studies – arrayed waveguide grating (AWG) and planar concave grating (PCG). First, principle of operation was understood in order to develop analytical solution for output field using Gaussian approximation of the field and Fourier Optics. Then, semi-analytical simulation tool of the spectral response for both multiplexer configurations was developed in MATLAB. Normal distribution of phase errors was introduced to semi-analytical AWG model, which allowed us to study the correlation between standard deviation of phase errors and the level of crosstalk of AWG spectral response. AWG at 5.65 µm was fabricated based on SiGe/Si technology using the MATLAB tool for design parameters calculation and P.Labeye’s tool for AWG geometry calculation. Devices with slightly varying parameters were characterized: AWG1 with 4.6 µm waveguides and 9µm MMI; AWG2 with 4.6 µm waveguides and 11µm MMI; AWG3 with 4.8 µm waveguides and 9µm MMI. Measurements of devices on chip 36 (center of the wafer) and chip 32 (side of the wafer) were performed and analyzed. Temperature measurements of AWG2 and AWG3 (chip 32 and chip 36) at points five temperature points showed linear dependence of spectral shift with the temperature which has a good correlation with simulation predictions.

[pt] As redes ópticas passivas de nova geração 2 (NG-PON2) estão estudando e considerando o WDM-PON (Wavelength-Division-Multiplexed Passive Optical Networks) como a nova arquitetura para as redes de acesso, é provável que esta arquitetura seja adotada num futuro como o padrão. No entanto, algumas instalações já foram realizadas em todo o mundo, a maior parte delas na Coréia do Sul. Com o objetivo de reduzir os custos de operação (OPEX) e garantir a qualidade do serviço (QoS) um sistema de supervisão e localização de falhas é necessário. Neste trabalho é proposto e demonstrado um OTDR sintonizável (Optical Time-Domain Reflectometer) para realizar o monitoramento de redes WDMPON em serviço. O método apresentado é provado para diferentes fontes laser sintonizáveis CW (Continuous Wave) e utiliza um amplificador óptico semicondutor (SOA) como comutador para o sinal de prova. O sistema de monitoramento é provado experimentalmente numa rede WDM-PON simulada no laboratório a qual utiliza um AWG (Arrayed Waveguide Grating) como distribuidor. Os resultados foram melhorados utilizando diferentes métodos para mitigar os efeitos de interferência. / [en] The Next Generation Passive Optical Network 2 (NG-PON2) is considering and studying wavelength-division-multiplexed passive optical networks (WDM-PONs) as the new architecture for access networks, this architecture is likely to be adopted in near future as standard. However some deployments have been achieved worldwide, most of them in South Korea. In order to lower the operational expenditure (OPEX) and guarantee quality-of-service (QoS) an in-service monitoring and fault localization system is required. We propose and demonstrate a tunable optical time-domain reflectometer (T-OTDR) for in-service monitoring of (WDM-PONs). The proposed method is proved for different continuous wave tunable laser sources (CW TLS), and uses semiconductor optical amplifier (SOA) as a switch for the probe signal. This monitoring system is experimentally proved in a simulated WDMPON employing a cyclic AWG (Arrayed Waveguide Grating) as wavelength distributor. We improve the results using different methods to mitigate the interference effects.

Multiple-input multiple-output (MIMO) radars, which utilize multiple transmitters and receivers to send and receive independent waveforms, have been actively investigated as a next generation radar technology inspired by MIMO techniques in communication theory. Complementary metal-oxide-semiconductor (CMOS) technology offers an opportunity for dramatic cost and size reduction for a MIMO array. However, the resulting formidable signal processing burden has not been addressed properly and remains a challenge. On the other hand, from a block-level point of view, an analog-to-digital converter (ADC) is required for mixed-signal processing to convert analog signals to digital signals, but an ADC occupies a significant portion of a system's budget. Therefore, improvement of an ADC will greatly enhance various trade-offs. This research presents an alternative and viable approach for a MIMO array from a system architecture point of view, and also develops circuit level improvement techniques for an ADC. This dissertation presents a fully-integrated analog pulse compressor (APC) based on an analog matched filter in a mixed signal domain as a key block for the waveform diversity MIMO radar. The performance gain of the proposed system is mathematically presented, and the proposed system is successfully implemented and demonstrated from the block level to the system level using various waveforms. Various figures of merit are proposed to aid system evaluations. This dissertation also presents a low-power ADC based on an asynchronous sample-and-hold multiplying SAR (ASHMSAR) with an enhanced input range dynamic comparator as a key element of a future system. Overall, with the new ADC, a high level of system performance without severe penalty on power consumption is expected. The research in this dissertation provides low-cost and low-power MIMO solutions for a future system by addressing both system issues and circuit issues comprehensively.