An atmospheric pressure radio frequency capacitively coupled plasma (CCP) has been developed and characterized for applications in atomic emission spectrometry (AES), atomic absorption spectrometry (AAS) and gas chromatography (GC). The CCP torch was initially designed as an atom reservoir for carrying out elemental analysis using atomic absorption. Functionally, the device consists of two parts, the CCP discharge tube and the tantalum strip electrothermal vaporization sample introduction system. The torch design provides for very effective energy transfer from the power supply to the plasma by capacitive coupling. Therefore, the plasma can be generated at atmospheric pressure with a flexible geometry. The plasma can be operated at very low rf input powers (30-600 W) enabling optimal conditions for atom resonance line absorption measurements. Absorption by the analyte takes place within the plasma discharge which is characterized by a long path length (20 cm) and low support gas flow rate (0.2 L/Min). Both of these characteristics ensure a relatively long residence time. The device exhibits linear calibration plots and provides sensitivities in the range of 3.5-40 pg. A preliminary measurement gave a Fe I excitation temperature of approximately 4000 K for the discharge. At this temperature, potential chemical interferences are likely to be minimal. Chemical interferences for Fe, Al, As, Ca, Co, Cd, Li, Mo and Sr were negligible in the determination of silver. Chloride interference, which is prevalent in GF-AAS, was not found. The amount of Ag found in a SMR#1643b (NIST) water sample was 9.5 ± 0.5 ng/g which fell in the certified range of 9.8 ± 0.8 ng/g. Spikes of 30 ng/g and 60 ng/g of silver were added to the SRM and recoveries were found to be in a range from 105 % to 96.2 %. The RSD obtained for 7 replicates of 270 pg silver was 4.6 %. The results for the CCP AES are even more promising. The interferences of thirteen elements are negligible in the determination of silver. The chloride interference was not found. The detection limits for Ag, Cd, Li, Sb and B are 0.7, 0.7, 2, 80 and 400 pg respectively. The amount of silver found in a SRM#1643b (NIST) water sample was 9.3 ± 0.5 ng/g which also fell in the certified range of 9.8 ±0.8 ng/g. Spikes of 30 ng/g and 60 ng/g of silver were added into the SRM#1643b (NIST) samples; the recoveries were found to range from 97 % to 104 %. The RSD obtained for 7 analyses of 270 pg silver were 1.5 % for CCP-AES. It was also found that the signal to noise ratios (S/N) are higher in the AES mode than those in the AAS mode in the same CCP atomizer. In order to exploit advantages inherent in both GF-AAS and I CP-AES, an atmospheric pressure capacitively coupled plasma sustained inside a graphite furnace was developed. This source combines the high efficiency of atomization in furnaces and the high efficiency of the excitation in atmospheric pressure plasmas. In general, plasma sources are able to effectively excite high-lying excited states for most metals and non-metals and can also ionize vaporized elements. Therefore the possibility exists of using non-resonance lines to avoid the effects of self-absorption at high analyte concentrations. Ion lines may also be used in cases where they provide better sensitivity or freedom from spectral interferences. This source also offers the ability to independently optimize vaporization and excitation. However, the most important aspect of this new source is that it can be used for simultaneous, multielement determinations of small sized samples in a graphite furnace atomizer, a design which has been proven to be effective over many years of use. Preliminary quantitative characteristics of this new atmospheric pressure plasma emission source have been studied. The detection limit for Ag of 0.3 pg is lower than the value of 0.4 pg reported for GF-AAS. Variants of the CCP, including a gas chromatography (GC) detector, combinations of laser ablation - CCP, rf sputtering - CCP direct solid analysis, and its application as an intense spectral lamp have been developed and are reported in this dissertation. / Science, Faculty of / Chemistry, Department of / Graduate

The alkylation of pyrimidyl aldehyde by diisopropylzinc has received immense attention over the last decade. This is mainly because the reaction which was discovered by Soai and coworkers is capable of achieving a homochiral product from an essentially achiral precursor. The strong amplification of the enantiomeric excess occurs because of a transition state complex which is responsible for autocatalysis. Clarifying the structural nature of the organometallic species involved in the reaction is vital for understanding the mechanism of the chiral amplification process. Known mechanistic details are patchy and based on studies that address molecular level details by NMR, computational chemistry, calorimetric and kinetic studies. The studies reported in this thesis for the first time directly addressed the nature of the intermediate by structural analysis with X-ray Absorption Fine Structure (XAFS) Spectroscopy at the Zn K-edge. These measurements provide bond distances, local coordination numbers and the geometry of ligands in the local environment around the Zn centres. First, the molecular level origin of the solvent dependencies in the asymmetric amplification by the Soai process is elucidated. A rationale for the behaviour of dialkylzinc compounds in polar and non-polar solvents is reported. Structural causes for often observed chirality depletion in polar solvents are elucidated. Further studies then examined the nature of the products formed by the reaction of various chiral ligands and dialkylzinc compounds. Different chiral ligands are examined and the complex structure was determined.Finally, first results of in situ studies of the reaction progress in continuous flow channel cells are reported.

No description available.

<p> Ni K extended X-ray absorption fine structure spectroscopy recorded with synchrotron radiation at 77 K and 300 K, has been used to investigate various annealed Pd40Ni40P20 metallic glass samples. The structural parameters (radial distance, coordination number, Debye Waller factor) for the Fourier filtered first coordination shell were obtained via curve analysis using MFIT (multifitting analysis) and plotted as a function of annealing temperature. Similar trends between 77 K and 300 K data were not observed in all cases. These results lead one to believe that the curve fitting procedure is not yet optimized and makes one sceptical of attributing any meaning to the results.</p> <p> X-ray absorption near edge spectroscopy via electron yield detection has also been used to study the B K edge in boron doped silicon. It was found that a strong peak at 195 eV is directly related to trigonally coordinated boron. Non trigonally coordinated boron did not seem to produce this spike. Results show that B 1s spectroscopy is a very sensitive probe of the local structure of boron.</p> / Thesis / Master of Science (MSc)

An active core fiber optic gas sensing technique has been developed by using a photonic crystal (PC) hollow core fiber (HCF) as a transducer and a tunable diode laser as a light source for multi-gas sensing. The intrinsic optical absorption signal of an analyte molecule in the near nfrared region is monitored for sensing C2H2,CO2 and NH3. Although the overtone absorptions are known to have low absorption cross-sections, this sensor can detect these gas components down to the parts-per-million (ppm) level by using a 1-meter hollow core fiber as a transducer. This sensor is an example of application of PC-HCF to gas sensor design. The sensitivity of this gas sensing technique can be improved by introducing periodic openings along the fiber, decreasing the hole diameter down to 0.5 mm and using a longer hollow optical fibers. Other advantages of this gas sensing technique include less interference, fast response and potential applications like high temperature, remote and corrosive gas sensing.

No description available.

El objetivo de esta tesis es estudiar la agrupación y el crecimiento de especies metálicas confinadas o soportadas en materiales porosos mediante espectroscopia de absorción de rayos X in situ. Para lograrlo, las especies de paladio y plata se han introducido en materiales porosos (¿-alúmina, carbón activo y zeolitas) mediante impregnación vía húmeda y métodos de intercambio iónico, respectivamente. Luego, el agrupamiento de estas especies metálicas se ha controlado mediante tratamientos de activación en diferentes atmósferas (inerte, oxidativa y reductiva) y seguido por XAS de manera detallada. El objetivo principal del trabajo actual es demostrar que tanto XANES como EXAFS pueden proporcionar información valiosa y, en cierto punto, innovadora durante el control de especies metálicas (en términos de tipo y tamaño de las especies). Aprovechando los procedimientos de análisis inusuales, como el análisis de los cumulantes, el ajuste de la parte imaginaria de la transformada de Fourier y otros, es posible obtener información refinada sobre los sistemas investigados. En la sección de introducción, se proporciona una compilación de estudios en los que se ha utilizado XAS como técnica importante para caracterizar especies metálicas en materiales porosos. Conscientes de que las personas pueden usar dicha introducción como base para estudios más complejos en el futuro, la discusión se ha dirigido tentativamente hacia este objetivo. El capítulo 4 se centra en el estudio de la influencia de los precursores de paladio y la naturaleza del soporte en las nanopartículas resultantes. El proceso de activación completo, es decir, la transformación precursor --> nanopartícula, ha sido seguido por XAS in situ. El análisis estuvo compuesto por el punto de partida (material impregnado), calcinación en flujo de O2 y reducción posterior con H2. La consecuencia del uso de diferentes precursores metálicos y soportes se ha discutido en términos del número de coordinación promedio obtenido a partir del análisis de datos de EXAFS, que fue respaldado por técnicas de caracterización de laboratorio. El capítulo 5 está dedicado al estudio de la agrupación de plata durante y después de los tratamientos de activación utilizando zeolitas de poro pequeño intercambiadas con plata como precursores y nanocontenedores. Se ha estudiado la influencia de la estructura y la composición química de los materiales basados en plata sobre las especies metálicas formadas en diferentes condiciones de agrupamiento y redispersión del metal (calcinación usando atmósferas distintas, reducción en H2, redispersión en O2) utilizando métodos de caracterización in situ o ex situ. Después, se discuten las consecuencias catalíticas de las zeolitas que contienen Ag en la reacción de SCO-NH3. En esta sección, la combinación de XAS in situ con varias técnicas de laboratorio ha demostrado ser fundamental para un completo entendimiento del trabajo. Finalmente, una lista de proyectos desarrollados en paralelo a esta tesis se proporciona al final de este documento. / The aim of this thesis is to study the clustering and growth of metallic species either confined or supported in porous materials by in situ X-ray absorption spectroscopy. To accomplish this task, palladium and silver species were introduced into porous materials (¿-alumina, activated carbon and zeolites) by wetness impregnation and ion-exchange methods, respectively. Then, the clustering of these metallic species was controlled by activation treatments in different atmospheres (inert, oxidative and reductive) and followed by XAS in a comprehensive way. The principal goal of current work is to demonstrate that both XANES and EXAFS can provide valuable and, at certain point, innovative information during tuning of metallic species (in terms of type and size). Taking advantage of unusual analysis procedures, such as cumulant approach, fitting of imaginary part of Fourier transform and others, it is possible to obtain refined information about the investigated systems. In the introduction section, a compilation of studies in which XAS was used as important technique to characterize metallic species in porous materials is provided. Conscious that people can use such introduction as a basis for more complex studies in the future, the discussion has been tentatively directed toward this goal. The chapter 4 is focused on the study of the influence of palladium precursors and the nature of support on the resultant nanoparticles. The whole activation process, i.e. the transformation precursor --> nanoparticle, was followed in situ by XAS. The analysis pathway was composed by the starting point (as-impregnated), calcination in O2 flow and posterior reduction with H2. The consequence of using distinct metal precursors and supports were discussed in terms of average coordination number obtained from EXAFS data analysis, which was co-supported by laboratory characterization techniques. The chapter 5 is dedicated to the study of silver clustering during and after activation treatments using Ag-containing small-pore zeolites as precursors and nanocontainers. The influence of framework structure and chemical composition of Ag-based materials on formed Ag species at different clustering and metal redispersion conditions (calcination using distinct atmospheres, reduction in H2, redispersion in O2) were studied using either in situ or ex situ characterization methods. After, the catalytic consequences of tuned Ag-containing zeolites in SCO-NH3 are discussed. In this section, the combination of in situ XAS with several laboratory techniques proved to be pivotal to have a full picture of the investigated system. Finally, a list of projects developed in parallel to this thesis is provided at the end of this document. / L'objectiu d'aquesta tesi és estudiar l'agrupació i el creixement d'espècies metàl·liques confinades o suportades en materials porosos mitjançant espectroscòpia d'absorció de raigs X in situ. Per a això, les espècies de pal·ladi i plata s'han introduït en materials porosos (¿-alúmina, carbó activat i zeolites) per mitjà de la impregnació via humida i mètodes d'intercanvi iònic, respectivament. Una vegada preparats els materials, l'agrupament de les espècies metàl·liques s'ha controlat fent ús de tractaments d'activació en diferents atmosferes (inert, oxidant i reductora) s'ha estudiat exhaustivament per XAS. L'objectiu principal del treball és demostrar que tant el XANES com l'EXAFS proporcionen informació rellevant i, en certa manera, innovadora per al control d'espècies metàl·liques (en termes de tipus i grandària d'aquestes espècies). Fent ús de procediments de tractament de dades no molt habituals com l'anàlisi de cumulants, l'ajust de la part imaginària de la transformada de Fourier i altres, és possible obtenir informació detallada sobre els sistemes estudiats. En l'apartat de la introducció, es proporciona una recopilació d'estudis en els quals s'ha utilitzat XAS com a tècnica principal per a caracteritzar les anomenades espècies metàl·liques en materials porosos. Aquesta introducció ha estat redactada per a que puga servir com a punt de partida per a futurs estudis que requereixen la utilització de XAS per a la caracterització de les espècies metàl·liques presents en els catalitzadors. El capítol 4 es centra en l'estudi de la influència dels precursors de pal·ladi i la naturalesa del suport front a les nanopartícules resultants. El procés d'activació, és a dir, la transformació precursor --> nanopartícula, ha sigut estudiat per XAS in situ. L'anàlisi per XAS va comprendre els següents passos: punt de partida (material impregnat), calcinació en flux d'O2 i reducció posterior amb H2. La utilització de diferents precursors i suports metàl·lics ha permès dur a terme una discussió, referent al nombre de coordinació mitjà obtingut a partir de l'anàlisi de dades de la zona EXAFS, que ha estat recolzat per altres tècniques de caracterització. El capítol 5 s'ha dedicat a l'estudi de l'agrupació de plata intercanviada en els catalitzadors durant i després dels tractaments d'activació. S'han utilitzat zeolites de porus xicotet, com la CHA i RHO, intercanviades amb plata. L'estudi de la influència de l'estructura zeolítica i la composició química dels materials enfront dels diferents tractaments d'activació (calcinació utilitzant diferents atmosferes, reducció en presència d'H2, re-dispersió en atmosfera d'O2) es va realitzar fent ús de mètodes de caracterització in situ o ex situ. A continuació, es discuteix la influència d'aquestes espècies metàl·liques formades, utilitzant els diferents mètodes d'activació, per a la reacció d'SCO-NH3. En aquest sentit, s'ha demostrat que la combinació de XAS in situ amb diverses tècniques habituals de laboratori és fonamental per al desenvolupament d'aquest treball. Finalment, es presenta una llista de projectes, en els quals també s'ha treballat paral·lelament, on s'ha utilitzat XAS com a tècnica de caracterització. / Wittee Lopes, C. (2018). Characterization of metallic species on porous materials by in situ XAS [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/107953

Lean, premixed combustion has enjoyed increased application due to the need to reduce pollutant emissions. Unfortunately, operating the flame at lean conditions increases susceptibility to thermoacoustic (TA) instability. Self-excited TA instabilities are a result of the coupling of the unsteady heat release rate of the flame with the acoustics of the combustion chamber. The result is large pressure oscillations that degrade performance and durability of combustion systems. Industry currently has no reliable tool to predict instabilities a priori. CFD simulations of full-scale, turbulent, reacting flows remain unrealizable. The work in this paper is part of a study that focuses on developing compact models of TA instabilities, i.e. acoustics and flame dynamics. Flame dynamics are defined as the response in heat release to acoustic perturbations. Models of flame dynamics can be coupled with models of combustor enclosure acoustics to predict TA instabilities. In addition, algorithms to actively control instabilities can be based on these compact models of flame dynamics and acoustics. The work outlined in this thesis aims at determining the flame dynamics model experimentally. Velocity perturbations are imparted on laminar and turbulent flames via a loudspeaker upstream of the flame. The response of the flame is observed through two measurements. Hydroxyl radical (OH*) chemiluminescence indicates the response in chemical reaction rate. Tunable Diode Laser Absorption Spectroscopy (TDLAS), centered over two water absorption features, allows a dynamic measurement of the product gas temperature. The response in product gas temperature directly relates to the enthalpy fluctuations that couple to the acoustics. Experimental frequency response functions of a laminar, flat-flame burner and a turbulent, swirl-stabilized combustor will be presented as well as empirical low-order models of flame dynamics. / Master of Science

This thesis reports work extending the scope of a recently developed gas sensing technique, multi-mode absorption spectroscopy (MUMAS). The ability of MUMAS to simultaneously detect multiple species from a mixture is demonstrated for the first time. The technique is subsequently extended to mid-infrared wavelengths, realising large gains in sensitivity. A solid-state, multi-mode laser has been developed to provide a high-performance comb source for use with MUMAS. This in-house constructed, diode-pumped, Er/Yb:glass laser operates on 10 longitudinal modes, separated by 18 GHz and centred close to 1565 nm. The extensive development and prototyping work leading to this final laser design is described. Multi-species detection with MUMAS is reported for the first time, thus demonstrating the ability of this technique to perform multi-gas sensing using a single laser and simple detection scheme. The previously described Er/Yb multi-mode laser was used to record MUMAS signals from a sample containing CO, C₂H₂, and N₂O. The components of the mixture were detected simultaneously by identifying multiple transitions in each of the species. Temperature- and pressure-dependent modelled spectral fits to the data were used to determine the partial pressures of each species in the mixture with an uncertainty better than +/-2%. Multi-mode radiation has been successfully generated at 3.3 μm using quasi phase matched difference frequency generation (QPM-DFG). A mid-infrared laser comb was produced by optically mixing the near-infrared, multi-mode comb produced by the previously developed Er/Yb:glass laser with the single-mode output of a Nd:YAG laser operating at 1064 nm. This multi-frequency laser source was characterised to verify performance, and subsequently used to perform proof-of-principle MUMAS measurements on the strong transitions found in this spectral region. Spectra were recorded of NH₃ and CH₄ both individually and as components of a mixture. A minimum detection level for this system was determined to be 4.3 μbar m^-1 for CH₄, a sensitivity increase of 300 over similar measurements performed in the near-IR.

Cavity enhanced spectroscopies (CES) are currently amongst the most sensitive spectroscopic techniques available for probing gas-phase samples, however their application to the liquid-phase has been more limited. Sensitive analysis of submicrolitre liquid samples is highly desirable, as miniaturisation allows for the reaction and analysis of scarce or expensive reagents, produces less waste, and can increase the speed of separations and reactions, whilst having a small footprint and high throughput. Absorption spectroscopy is a particularly desirable technique due to its universal, label-free nature, however its application to small volume liquid samples is hampered by the associated short absorption pathlengths, which limit sensitivity. CES improve sensitivity by trapping light within a confined region, increasing the effective pathlength through the sample. Three distinct types of optical cavity were constructed and evaluated for the purposes of making optical absorption measurements on liquid samples. The first incorporated a high optical quality flow cell into a "macrocavity" formed from two dielectric mirrors separated by 51.3 cm. Cavity losses were minimised by positioning the flow cell at Brewster's angle to the optical axis, and the setup was used to perform a single-wavelength cavity ringdown spectroscopy experiment to detect and quantify nitrite within aqueous samples. The detection limit was determined to be 8.83 nM nitrite in an illuminated volume of only 74.6 nL. Scattering and reflective losses from the flow cell surfaces were found to be the largest barrier to increased sensitivity, leading us to focus on the integration of cavity mirrors within a microfluidic flow system in the work that followed. In the second set of experiments, cavity enhanced absorption spectroscopy (CEAS) measurements were performed on Thymol Blue using custom-made microfluidic chips with integrated cavity mirrors. Unfortunately, due to the plane-parallel configuration of the mirrors and the corresponding difficulty in sustaining stable cavity modes, the results were underwhelming, with a maximum cavity enhancement factor (CEF) of only 2.68. At this point, attention was focussed toward a more well-defined cavity geometry: open-access plano-concave microcavities. The microcavities consist of an array of micron-scale concave mirrors opposed by a planar mirror, with a pathlength that is tunable to sub-nanometer precision using piezoelectric actuators. In contrast to the other experimental setups described, themicrocavities allow for optical measurements to be performed in which we monitor the change of wavelength and/or amplitude of a single well-defined cavity mode in response to a liquid sample introduced between the mirrors. In the first microcavity experiment, we used 10 &mu;m diameter mirrors with cavity lengths from 2.238 &mu;m to 10.318 &mu;m to demonstrate refractive index sensing in glucose solutions with a limit of detection of 3.5 x 10^-4 RIU. The total volume of detection in our setup was 54 fL. Thus, at the limit of detection, the setup can detect the change of refractive index that results from the introduction of 900 zeptomoles (500,000 molecules) of glucose into the device. The microcavity sensor was then adapted to enable broadband absorption measurements of methylene blue via CEAS. By recording data simultaneously from multiple cavities of differing lengths, absorption data is obtained at a number of wavelengths. Using 10 &mu;m diameter mirrors with cavity pathlengths from 476 nm to 728 nm, a limit of detection, expressed as minimum detectable absorption per unit pathlength, of 1.71 cm^-1 was achieved within a volume of 580 attolitres, corresponding to less than 2000 molecules within the mode volume of the cavity. Finally, a new prototype was developed with improved cavity finesse, a much more intense and stable light source, and improved flow design. Using a single plano-concave microcavity within the array with a cavity pathlength of 839.7 nm, and 4 &mu;m radius of curvature mirror, absorption measurements were performed on Methylene Blue. Analysis of this data indicated a CEF of around 9270, and a limit of detection based on the measured signal-to-noise ratio of 0.0146 cm^-1. This corresponds to a minimum detectable concentration of 104 nM Methylene Blue, which given the mode volume of 219 aL, suggests a theoretical minimum detectable number of molecules of 14.