The object of this research was to investigate dispersion in surface phononic crystals (PnCs) for application to a newly developed passive surface acoustic wave (SAW) ozone sensor. Frequency band gaps and slow sound already have been reported for PnC lattice structures. Such engineered structures are often advertised to reduce loss, increase sensitivity, and reduce device size. However, these advances have not yet been realized in the context of surface acoustic wave sensors. In early work, we computed SAW dispersion in patterned surface structures and we confirmed that our finite element computations of SAW dispersion in thin films and in one dimensional surface PnC structures agree with experimental results obtained by laser probe techniques. We analyzed the computations to guide device design in terms of sensitivity and joint spectral operating point. Next we conducted simulations and experiments to determine sensitivity and limit of detection for more conventional dispersive SAW devices and PnC sensors. Finally, we conducted extensive ozone detection trials on passive reflection mode SAW devices, using distinct components of the time dispersed response to compensate for the effect of temperature. The experimental work revealed that the devices may be used for dosimetry applications over periods of several days.

The analysis and development of robust sensing platforms based on solidly-mounted ZnO bulk acoustic wave devices was proposed. The exploitation of acoustic energy trapping was investigated and demonstrated as a method to define active sensing areas on a substrate. In addition, a new "hybrid" acoustic mode experiencing acoustic energy trapping was studied theoretically and experimentally. This mode was used as an explanation of historical inconsistencies in observed thickness-shear mode velocities. Initial theoretical and experimental results suggest that this mode is a coupling of thickness-shear and longitudinal particle displacements and, as such, may offer more mechanical and/or structural information about a sample under test. Device development was taken another step further and multi-mode ZnO resonators operating in the thickness-shear, hybrid, and longitudinal modes were introduced. These devices were characterized with respect to sample viscosity and conductivity and preliminary results show that, with further development, the multi-mode resonators provide significantly more information about a sample than their single-mode counterparts. An alternative to resonator-based platforms was also presented in the form of bulk acoustic delay lines. Initial conceptual and simulation results show that these devices provide a different perspective of typical sensing modalities by using properly designed input pulses, device tuning, and examining overall input and output signal spectra.

Thesis (M.S.)--Joint Program in Oceanographic Engineering (Massachusetts Institute of Technology, Dept. of Ocean Engineering; and the Woods Hole Oceanographic Institution), 1997. / Includes bibliographical references (p. 65-66). / The Surface Suspended Acoustic Receiver (SSAR) is a free-drifting platform intended for use as a receiver in large scale acoustic tomography experiments. Early prototypes of the SSAR exhibited very poor signal-to-noise ratios in the frequency band of the hydrophones. This thesis details efforts to reduce the hydrophone noise level by combining the analysis of experimental data with the results from numerical models. Experiments were conducted to quantify both the frequency content and magnitude of noise generated on the SSAR. Through a program of sea trials and pond testing, two noise sources were identified. The dominant source of noise in the SSAR is velocity dependent flow noise that results from turbulent pressure fluctuations on the hydrophones. A second noise source results from the acceleration sensitivity of the hydrophones in conjunction with high frequency accelerations present in the hydrophone array cable. These high frequency accelerations also show a velocity dependence. The presence of the acceleration-induced noise leads to correlations between the signals from adjacent hydrophones, thus distorting the typical picture that flow noise should be uncorrelated along an array. The primary methods of eliminating the noise are encapsulating the hydrophone in a flow shield, eliminating the array cable, and slowing the system down by replacing the wave following surface buoy with a spar buoy. Using the experimental results, empirical relationships between hydrophone velocity and expected noise level are formed for both shielded and unshielded hydrophones. The numerical models developed as a part of this effort are then used to predict the velocities for a wide range of possible SSAR configurations. The models can also provide information, such as system tensions, that is useful in evaluating the longevity and survivability of SSARs. Modeled design fixes include subsurface component changes as well as comparing a wave following surface buoy to a spar buoy. / by Jason I. Gobat. / M.S.

Surface acoustic wave (SAW) sensors offer a wireless, passive sensor solution for use in numerous environments where wired sensing can be expensive and infeasible. Single carrier frequency SAW sensor embodiments such as delay lines, and resonators have been used in single sensor environments where sensor identification is not a necessity. The orthogonal frequency coded (OFC) SAW sensor tag embodiment developed at UCF uses a spread spectrum approach that allows interrogation in a multi-sensor environment and provides simultaneous sensing and sensor identi- fication. The SAW device is encoded via proper design of multiple Bragg reflectors at differing frequencies. To enable accurate device design, a model to predict reflectivity over a wide range of electrode metallization ratios and metal thicknesses has been developed and implemented in a coupling of modes (COM) model. The high coupling coefficient, reflectivity and temperature coefficient of delay (TCD) of YZ LiNbO3 makes it an ideal substrate material for a temperature sensor, and the reflectivity model has been developed and verified for this substrate. A new concept of pseudo-orthogonal frequency coded (POFC) SAW sensor tags has been investigated, and with proper design, the POFC SAW reduces device insertion loss and fractional bandwidth compared to OFC. OFC and POFC sensor devices have been fabricated at 250 MHz and 915 MHz using fundamental operation, and 500 MHz and 1.6 GHz using second harmonic operation. Measured device results are shown and compared with the COM simulations using the iii enhanced reflectivity model. Additionally, the first OFC devices at 1.05 GHz were fabricated on 128o YX LiNbO3 to explore feasibility of the material for future use in OFC sensor applications. Devices at 915 MHz have been fabricated on YZ LiNbO3 and integrated with an antenna, and have then been used in a transceiver system built by Mnemonics, Inc. to wirelessly sense temperature. The first experimental wireless POFC SAW sensor device results and predictions will be presented.