Spelling suggestions: "subject:"aircraft eontrol"" "subject:"aircraft 7control""
1 |
Application of bifurcation analysis to multiple attractor flight dynamicsLowenberg, Mark H. January 1998 (has links)
No description available.
|
2 |
Application of Eigenstructure Assignment to the control of powered lift combat aircraftSmith, Phillip Raymond January 1990 (has links)
No description available.
|
3 |
Attitude determination using low frequency radio polarisation measurementsMaguire, Sean Thomas George January 2015 (has links)
No description available.
|
4 |
Modeling, state estimation and control of unmanned helicopters. / 無人直昇機的動態模型建構、導航及控制器設計 / Wu ren zhi sheng ji de dong tai mo xing jian gou, dao hang ji kong zhi qi she jiJanuary 2012 (has links)
無人直昇機是指在沒有搭載駕駛員下,能自動飛行的直昇機。這種飛行器除了不用令駕駛員冒上性命風險,亦由於其獨特飛行能力,例如空中旋停、急彎打轉等,令無人直昇機在執行危險任務上有著重要的優勢。但同時,由於沒有了駕駛員的關係,這種飛行器持續面對著一系列的技術難點。當中包括:(一)在飛行上,無人直昇機帶有一種未能確解的動態反應,偶合在主控軸上,令動態變化的預測變得困難;(二)絶大部份無人直昇機的導航倚賴全球定位儀,但這種定位儀卻極易受干擾,影響飛行安全;(三)由於每次任務的需要,機上搭載物的位置及多寡令飛行器上的重力分佈經常改變,令自動控制器需面密集的手動調度及系統識別。 / 對於無人直昇機的動態模型建構,我們提出了一種新辦法令過往未能確解的偶合動態反應,能被準確的量化及分析,因而使這種模型能更準確預測無人直昇機的動態變化。我們的辦法針對過往一種普遍使用但不能預測偶合動態反應,名為「遲相」的模型方法,並提出以主旋槳上的陀螺現像,去描述無人直昇機上的偶合動態反應。另外,我們的模型分析顯示出準確預測無人直昇機的動態反應需要識別一系列難以度測而又經常變化的系統參數,因此我們提出以一個相對隱性模型的辦法對解決往後有關導航及控制的問題更有利。 / 有關無人直昇機的導航,我們提出以慣性感測器去補償全球定位儀因干擾及訊號異常導致的感測數據中斷。通過一系列的噪音處理,我們的辦法能從慣性感測器的加速度讀數轉化為位移,從而令無人直昇機能在突如其來的全球定位儀中斷作出即時反應,避免因位置讀數中斷而墜毀。除此以外,我們亦提供全自動參數調節算法,令整個噪音處理能快速應用於不同慣性感測器的設置上。 / 有關無人直昇機的控制,由於一般需要廣泛的系統建模及識別,因此我們提出以「能力轉移」的概念,透過駕駛員的示範,提取控制直昇機的技巧從而令機器無需建構準確和全面的動態模型下,能準確控制無人直昇機。我們通過建立一個簡明的反饋模型,利用的駕駛員的示範而自動配置出最適合的參數去控制無人直昇機。 / 從更準確的動態模型分析,到抗干擾導航及新型控制器的設計,整個研究為無人直昇機的發展提出了多方面的觀點及解決辦法。與此同時,我們的最終目的是希望為無人直昇機的日常應用上掃除因為缺少了駕駛員而做成的障礙,令無人直昇機能真正以最少的人為干涉而達至全面的無人操作。 / Unmanned helicopters hold both tremendous potential and challenges. Without risking the lives of human pilots, these vehicles exhibit agile movement and the ability to hover and hence open up a wide range of applications in the hazardous situations. Sparing human lives, however, comes at a stiff price for technology. Some of the key difficulties that arise in these challenges are: (i) There are unexplained cross-coupled responses between the control axes on the hingeless helicopters that have puzzled researchers for years. (ii) Most, if not all, navigation on the unmanned helicopters relies on Global Navigation Satellite Systems (GNSSs), which are susceptible to jamming. (iii) It is often necessary to accommodate the re-configurations of the payload or the actuators on the helicopters by repeatedly tuning an autopilot, and that requires intensive human supervision and/or system identification. / For the dynamics modeling and analysis, we present a comprehensive review on the helicopter actuation and dynamics, and contributes toward a more complete understanding on the on-axis and off-axis dynamical responses on the helicopter. We focus on a commonly used modeling technique, namely the phase-lag treatment, and employ a first-principles modeling method to justify that (i) why that phase-lag technique is inaccurate, (ii) how we can analyze the helicopter actuation and dynamics more accurately. Moreover, these dynamics modeling and analysis reveal the hard-to-measure but crucial parameters on a helicopter model that require the constant identifications, and hence convey the reasoning of seeking a model-implicit method to solve the state estimation and control problems on the unmanned helicopters. / For the state estimation, we present a robust localization method for the unmanned helicopter against the GNSS outage. This method infers position from the acceleration measurement from an inertial measurement unit (IMU). In the core of our method are techniques of the sensor error modeling and the filtering method for the sensor noise compensation. Moreover, we provide a fully automatic algorithm to tune our method. Finally, we evaluate our method on an instrumented gasoline helicopter. Experiments show that the technique enables the robust positioning of flying helicopters when no GNSS measurement is available. / The design of an autopilot for an unmanned helicopter is made difficult by its nonlinear, coupled and non-minimum phase dynamics. Here, we consider a reinforcement learning approach to transfer motion skills from human to machine, and hence to achieve autonomous flight control. By making efficient use of a series of state-and-action pairs given by a human pilot, our algorithm bootstraps a parameterized control policy and learns to hover and follow trajectories after one manual flight. One key observation our algorithm is based on is that, although it is often difficult to retrieve the human pilots’ hidden desiderata that formulate their state-feedback mechanisms in controlling the helicopters, it is possible to intercept the states of a helicopter and the actions by a human pilot and then to fit both into a model. We demonstrate the performance of our learning controller in experiments. / The results described in this dissertation shed new and important light on the technology necessary to advance the current state of the unmanned helicopters. From a comprehensive dynamics modeling that addresses perplexing cross-couplings on the unmanned helicopters, to a robust state estimation against GNSS outage and a learn-from-scarcesample control for an unmanned helicopter, we provide a starting point for the cultivation of the next-generation unmanned helicopters that can operate with the least possible human intervention. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Lau, Tak Kit. / Thesis (Ph.D.)--Chinese University of Hong Kong, 2012. / Includes bibliographical references (leaves 182-198). / Abstract also in Chinese. / Abstract --- p.i / Acknowledgement --- p.v / Chapter 1 --- Introduction --- p.1 / Chapter 1.1 --- The State-of-the-Art --- p.5 / Chapter 1.2 --- Problemand Approach --- p.8 / Chapter 1.3 --- Contributions and Organization of Chapters --- p.13 / Chapter 2 --- Actuation and Dynamics of Helicopter --- p.16 / Chapter 2.1 --- Introduction --- p.17 / Chapter 2.2 --- Input-Output Relation of Hingeless Helicopters --- p.20 / Chapter 2.3 --- Helicopter Dynamics --- p.30 / Chapter 2.3.1 --- Aerodynamics --- p.34 / Chapter 2.3.2 --- Discrepancy and Conventional Treatment --- p.36 / Chapter 2.3.3 --- Gyroscopically InducedMoment --- p.38 / Chapter 2.3.4 --- Example of Pitching Forward --- p.42 / Chapter 2.4 --- Empirical Evaluations --- p.44 / Chapter 2.4.1 --- Numerical Simulation --- p.45 / Chapter 2.4.2 --- Experiments --- p.47 / Chapter 2.5 --- Summary --- p.48 / Chapter 3 --- State Estimation against GNSS Outage --- p.53 / Chapter 3.1 --- Introduction --- p.55 / Chapter 3.2 --- Sensor Noises --- p.62 / Chapter 3.2.1 --- Sensitivity Analysis of Estimation Accuracy --- p.63 / Chapter 3.2.2 --- Sensor Error Characteristics --- p.68 / Chapter 3.2.3 --- Random Walk Acceleration Noise --- p.71 / Chapter 3.3 --- State Estimation Algorithm --- p.76 / Chapter 3.3.1 --- Process and Measurement Models --- p.79 / Chapter 3.3.2 --- Selection of OperationModes --- p.83 / Chapter 3.3.3 --- Prioritized Propagation of States --- p.85 / Chapter 3.4 --- Automatic Tuning of Filter Parameters --- p.87 / Chapter 3.4.1 --- Performance Index --- p.88 / Chapter 3.4.2 --- Tuning Algorithm --- p.90 / Chapter 3.5 --- Experimental Results --- p.93 / Chapter 3.6 --- Summary --- p.97 / Chapter 4 --- Model-based Control for Unmanned Helicopters --- p.106 / Chapter 4.1 --- Introduction --- p.107 / Chapter 4.2 --- Effect of Center of Gravity --- p.108 / Chapter 4.3 --- Design of Attitude Controller --- p.110 / Chapter 4.4 --- Augmentation in Controller and Experimental Results --- p.113 / Chapter 4.5 --- Summary --- p.117 / Chapter 5 --- Learning Control for Unmanned Helicopters --- p.120 / Chapter 5.1 --- Introduction --- p.121 / Chapter 5.2 --- RelatedWork --- p.124 / Chapter 5.3 --- Preliminary --- p.129 / Chapter 5.3.1 --- Derivation of Policy Gradient --- p.133 / Chapter 5.4 --- Controller Design --- p.133 / Chapter 5.4.1 --- Learning Dynamics --- p.135 / Chapter 5.4.2 --- Learning Control --- p.137 / Chapter 5.5 --- Performance Analysis --- p.141 / Chapter 5.5.1 --- Baseline --- p.141 / Chapter 5.5.2 --- Numerical Analysis --- p.145 / Chapter 5.6 --- Convergence Analysis --- p.152 / Chapter 5.7 --- Evaluation --- p.153 / Chapter 5.7.1 --- Simulation - Acrobot --- p.153 / Chapter 5.7.2 --- Simulation - Fixed-wing Aircraft --- p.154 / Chapter 5.7.3 --- Experiment - RC Car --- p.158 / Chapter 5.7.4 --- Experiment - Helicopter --- p.161 / Chapter 5.8 --- Summary --- p.169 / Chapter 6 --- Conclusion --- p.171 / Chapter A --- List of Publications & Awards --- p.177 / Chapter A.0.1 --- Publications --- p.177 / Chapter A.0.2 --- Awards --- p.181 / Bibliography --- p.182
|
5 |
A localization system using inertial measurement units and RGB-D sensor for unmanned aerial vehicles: 一套用於無人機定位的姿態感測元件及三維視覺感測器複合系統 / 一套用於無人機定位的姿態感測元件及三維視覺感測器複合系統 / CUHK electronic theses & dissertations collection / localization system using inertial measurement units and RGB-D sensor for unmanned aerial vehicles: Yi tao yong yu wu ren ji ding wei de zi tai gan ce yuan jian ji san wei shi jue gan ce qi fu he xi tong / Yi tao yong yu wu ren ji ding wei de zi tai gan ce yuan jian ji san wei shi jue gan ce qi fu he xi tongJanuary 2015 (has links)
相對於在地面上行走的機器人, 自動無人飛機擁有高自由度及靈活操控性。在對人類有危險的環境中,無人飛機更特別可以全自動或供操作員安全地遙距控制來執行危險工作。但無線連結不能確保安全及穩定,所以基於安全性考慮自動無人機上必需擁有自主運算能力以用於自動定位,返航及避障。 / 可是制作全自動無人機有很多的限制,如小型無人飛機上只能使用較小型馬達,載重十分少,故能被作為主要的計算機也不能使用強大的圖像處理器(GPU),所以只能使用運算能力較低的一般處理器(CPU)。此外,傳統的圖像處理定位方法也只能在強大硬件下實時運行,這種種的限制加起來使得小型無人飛機的自動定位成為難題。 / 一般現在的無人機,例如作為航空拍攝的,都是使用簡單而小型的全球定位系統感測器,所需要的運算器硬件要求也不高。但是這些無人飛機卻不能被用於室內或靠近建築物的地方,因為衛星定位信號會被多重反射甚至是阻隔開來。此外,全球定位系統普不能給予無人機有關機體附近環境的訊息,例如視覺特徵及三維結構等。所以無人機並沒有能力避開環境中的障礙物或甚至危害人身安全。 / 我們設計了飛行控制器,內含恣態感測組件,光流傳感器及高度計等元件作控制及感測。我們也提出了一個全自動的校準方法用於低成本的恣態感測器,當中並不需要任何人為的操作或昂貴和精準的的校準儀器。 / 除了恣態感測組件用於機體動作測量外,環境資訊都是對自動飛行有很大用的。我們所建構的無人飛機平台上使用了多種不同的運算組件及視覺定位算法,目的在於提拱一個有效,快速且能於飛機上裝置的電腦實時運算的定位系統。 / 從本論文所展示的結果中可得悉我們在無人機的及展,包括如何把低成本的恣態感測器校正的方法以增加準確性及從環境視覺特徵及三維結構幫助計算無人機自身位置的定位方法。我們希望本研究論文能對下一世代的自動無人機發展有幫助。 / Unmanned Aerial Vehicles (UAVs) process great maneuverability over ground vehicles, legged and tracked robots. UAVs can do more dangerous tasks where human can safely tele-operate from far away. However stable communication channels may not be guaranteed and therefore autonomous onboard processing for safety-concerned functions such as localization, homing or obstacles avoidance are essential. / UAVs have more limitations than others, typically the payload weight is significantly reduced compared to ground vehicles with powerful motors. Other limitations such as limited computing power for light-weight computer modules being put on-board lend the difficulty to the localization and control of the agile UAVs using traditional computationally exhausting Visual SLAM approaches. / Although the traditional simple GPS-Inertial approaches are beautiful that the hardware requirement is not so demanding, they cannot be applied in indoor or near indoor environments due to signal jamming and multiple-reflection. Additionally, GPS cannot provide any information about the environment arround the UAV so it raises risk for the UAV to danger such as obstacles collision which may cause serious injury to human. / To implement an autonomous aerial vehicle we built our flight-controller with a low-cost inertial measurement unit (IMU) and optical ow sensor and altimeter for motor control and sensing. The low-cost IMU suffers from bad measurement bias and drifts. We proposed a fully autonomous calibration method where no human intervention nor precise calibration equipment is needed. / Besides the IMU which can only provide body motion sensing, the perception about the environment is required for autonomous flying and avoid obstacles. We implemented a visual localization algorithm which runs efficiently in realtime on our light-weight and low-cost computer module. We have built a set of UAV system with an RGB-D Kinect sensor, which fuse different sensor measurements together for the localization. / The results presented in this thesis show a new possiblity to advance current development on Unmanned Aerial Vehicles. From the autonomous calibration method for low-cost IMU to improve accuracy orientation estimation to 3D localization using the perception of the environment features and structures from RGB-D sensor. At the same time we hope that our experience on the hardware building and real-time localization algorithm implementations can help boosting the advancement of the next generation of autonomous aerial vehicles. / Cheuk, Chi Ming. / Thesis M.Phil. Chinese University of Hong Kong 2015. / Includes bibliographical references (leaves 88-96). / Abstracts also in Chinese. / Title from PDF title page (viewed on 05, October, 2016). / Cheuk, Chi Ming. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only.
|
6 |
An active vision system for tracking and mosaicking on UAV.January 2011 (has links)
Lin, Kai Wun. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2011. / Includes bibliographical references (leaves 120-127). / Abstracts in English and Chinese. / Abstract --- p.i / Acknowledgement --- p.iii / Chapter 1 --- Introduction --- p.1 / Chapter 1.1 --- Overview of the UAV Project --- p.1 / Chapter 1.2 --- Challenges on Vision System for UAV --- p.2 / Chapter 1.3 --- Contributions of this Work --- p.4 / Chapter 1.4 --- Organization of Thesis --- p.6 / Chapter 2 --- Image Sensor Selection and Evaluation --- p.8 / Chapter 2.1 --- Image Sensor Overview --- p.8 / Chapter 2.1.1 --- Comparing Sensor Features and Performance --- p.9 / Chapter 2.1.2 --- Rolling Shutter vsGlobal Shutter --- p.10 / Chapter 2.2 --- Sensor Evaluation through USB Peripheral --- p.11 / Chapter 2.2.1 --- Interfacing Image Sensor and USB Controller --- p.12 / Chapter 2.2.2 --- Image Sensor Configuration --- p.14 / Chapter 2.3 --- Image Data Transmitting and Processing --- p.17 / Chapter 2.3.1 --- Data Transfer Mode and Buffering on USB Controller --- p.18 / Chapter 2.3.2 --- Demosaicking of Bayer Image Data --- p.20 / Chapter 2.4 --- Splitting Images and Exposure Problem --- p.22 / Chapter 2.4.1 --- Buffer Overflow on USB Controller --- p.22 / Chapter 2.4.2 --- Image Luminance and Exposure Adjustment --- p.24 / Chapter 3 --- Embedded System for Vision Processing --- p.26 / Chapter 3.1 --- Overview of the Embedded System --- p.26 / Chapter 3.1.1 --- TI OMAP3530 Processor --- p.27 / Chapter 3.1.2 --- Gumstix Overo Fire Computer-on-Module --- p.27 / Chapter 3.2 --- Interfacing Camera Module to the Embedded System --- p.28 / Chapter 3.2.1 --- Image Signal Processing Subsystem --- p.29 / Chapter 3.2.2 --- Camera Module Adapting Board --- p.30 / Chapter 3.2.3 --- Image Sensor Driver and Program Development --- p.31 / Chapter 3.3 --- View-stabilizing Biaxial Camera Platform --- p.34 / Chapter 3.3.1 --- The New Camera System iv --- p.35 / Chapter 3.3.2 --- View-stabilizing Pan-tilt Platform --- p.41 / Chapter 3.4 --- Overall System Architecture and UAV Integration --- p.46 / Chapter 4 --- Target Tracking and Geo-locating --- p.50 / Chapter 4.1 --- Camera Calibration --- p.51 / Chapter 4.1.1 --- The Perspective Camera Model --- p.51 / Chapter 4.1.2 --- Camera Lens Distortions --- p.53 / Chapter 4.1.3 --- Calibration Toolbox and Results --- p.54 / Chapter 4.2 --- Selection of Object Features and Trackers --- p.56 / Chapter 4.2.1 --- Harris Corner Detection --- p.58 / Chapter 4.2.2 --- Color Histogram --- p.59 / Chapter 4.2.3 --- KLT and Mean-shift Tracker --- p.59 / Chapter 4.3 --- Target Auto-centering --- p.64 / Chapter 4.3.1 --- Formulation of the PID Controller --- p.65 / Chapter 4.3.2 --- Control Gain Settings and Tuning --- p.69 / Chapter 4.4 --- Geo-locating of Tracked Target --- p.69 / Chapter 4.4.1 --- Coordinate Frame Transformation --- p.70 / Chapter 4.4.2 --- Depth Estimation and Target Locating --- p.74 / Chapter 4.5 --- Results and Discussion --- p.77 / Chapter 5 --- Real-time Aerial Mosaic Building --- p.89 / Chapter 5.1 --- Motion Model Selection --- p.90 / Chapter 5.1.1 --- Planar Perspective Motion Model --- p.90 / Chapter 5.2 --- Feature-based Image Alignment --- p.91 / Chapter 5.2.1 --- Image Preprocessing --- p.91 / Chapter 5.2.2 --- Feature Extraction and Matching --- p.92 / Chapter 5.2.3 --- Image Alignment using RANSAC Algorithm --- p.94 / Chapter 5.3 --- Image Composition --- p.95 / Chapter 5.3.1 --- Image Blending with Distance Map --- p.96 / Chapter 5.3.2 --- Overall Stitching Process --- p.98 / Chapter 5.4 --- Mosaic Simulation using Google Earth --- p.99 / Chapter 5.5 --- Results and Discussion --- p.100 / Chapter 6 --- Conclusion and Further Work --- p.108 / Chapter A --- System Schematics --- p.111 / Chapter B --- Image Sensor Sensitivity --- p.118 / Bibliography --- p.120
|
7 |
The design of a hingeline electro-mechanical actuatorKendrick, Kevin Stuart 18 August 2015 (has links)
Aircraft control mechanisms, such as those that operate the flaps, ailerons, rudders, etc., are almost exclusively driven by hydraulic-based systems. Their popularity in flight control systems is not unfounded; hydraulic actuators are quite torque-dense and benefit from decades of development bringing operating performance to a high level. On the other hand the infrastructure to support this system increases weight, adds system development complexity, and reduces aircraft maintainability [Jensen et al, 2000]. Based on recent Electro-Mechanical Actuator (EMA) development and design efforts at the Robotics Research Group (RRG), a new opportunity exists to replace current hydraulic flight control systems with those powered by electricity through a national program [Tesar, 2005]. A literature review of the topic found a 30 year old effort by AiResearch to develop a similarly powered hingeline actuator with given traditional performance goals (torque capacity, redundancy, output speed, reliability). In this report,a thorough analysis is performed on each major component group to quantitatively evaluate this baseline device. Using component technologies developed at RRG, this report proposes a dual torque-summing electromechanical actuator, each with a star compound / hypocyclic combined gear train, designed to exceed the performance of the original (1976) AiResearch project. This preliminary design exercise includes a layout of the entire actuator along with an appropriate analysis of major components including bearings, gear train, motor, housing, and release mechanism. The performance of this gear train is critical to overall actuator success and fundamental analytics have already been developed in this area [Park and Tesar, 2005]. Finite Element Analysis on the gear train and housing provide early design feedback and verification of actuator performance characteristics. In particular, simulation results show the gear stiffness, load sharing, and torque capacities exceed analytical estimates. Finally, four different comparisons are presented that evaluate configuration variations of the two designs based on applicable performance criteria. Results show the RRG fault-tolerant actuator has a marked improvement over the baseline in average stiffness (14.2x), reflected inertia (3.2x) and nominal torque density (3.4x). The chapter next lists actuator test methods and aircraft qualification standards. Finally, a summary of future work is detailed in a ten step outline to bring this EMA technology to a level of early deployment in a large range of aircraft systems.
|
8 |
Mission-based guidance system design for autonomous UAVsMoon, Jongki. January 2009 (has links)
Thesis (Ph.D)--Aerospace Engineering, Georgia Institute of Technology, 2010. / Committee Chair: Prasad, JVR; Committee Member: Costello, Mark; Committee Member: Johnson, Eric; Committee Member: Schrage, Daniel; Committee Member: Vela, Patricio. Part of the SMARTech Electronic Thesis and Dissertation Collection.
|
9 |
Development of a seamless morphing wingPetersen, Michael January 2010 (has links)
Thesis (MTech (Mechanical Engineering))--Cape Peninsula University of Technology, 2010. / The Cape Peninsula University of Technology (CPUT) Advanced Manufacturing and
Technology Laboratory (AMTL) developed an Unmanned Aerial Vehicle (UAV)
Technology Demonstrator for the purpose of testing and maturing adaptronic
devices. Extending the flight envelope of this unmanned aerial vehicle by increasing
its range and endurance is the next step in its development. A seamless variable
angle of incidence (sVAI) morphing wing is proposed to increase the lift with little
coupling to drag during takeoff; and decrease the drag with little effect on lift during
climb, thus increasing the total flight performance of the aircraft. CAD models of the
conceptualized sVAI wing and a conventional (CON) wing, as used on the
Technology Demonstrator, were modeled. Numerical analyses on these CAD models
showed that the sVAI wing concept at a 4° twist decreased the ground roll distance
and stall velocity by ±17% and ±31% respectively, as compared to the CON wing in
standard takeoff configuration. This allowed for ± 11.7% less power required for
takeoff allowing the aircraft to get to its operational altitude quicker, thus saving fuel
and reducing energy losses; and increasing range and endurance. The results also
showed that the sVAI wing concept could reduce the drag during climb by ± 14%,
but the lift is also proportionately reduced thus having little improvement on the
climb phase of flight performance. A prototype of the morphing wing was then
conceptualized and designed, using a 3D CADmodeler, and then manufactured. The
product development chain produced for this morphing wing included two rapid
prototyping machines and reverse engineering technologies. The chain allowed for
the rapid manufacturing of light weight and intricate parts. The manufactured wing is
then incorporated into a test rig to compare the actual morphing ability of the
prototype to the theoretical morphing ability of the CADmodel, and thus make flight
performance predictions of the actual vehicle. 3D scans were taken of the prototype
and then converted to 3D CADfiles. The geometrical and topographical deformation
of the prototype was then compared to that of the CAD model showing an average difference of ±1.2% and ±3% at maximum positive and negative configurations,
respectively. This allowed one to make the prediction that the sVAI wing will increase
the performance of the Technology Demonstrator.
|
10 |
Future technological factors affecting unmanned aircraft systems (UAS):a South African perspective towards 2025Marope, Tumisang January 2015 (has links)
The fact that pilots are not physically situated in the aircraft for UAS operations makes the current standards applicable to manned aircraft not suitable for UAS operations (FAA, 2013). FAA (2013:18) states that ―removing the pilot from the aircraft creates a series of performance considerations between manned and unmanned aircraft that need to be fully researched and understood to determine acceptability and potential impact on safe operations in the NAS. According to ERSG (2013), not all technologies necessary to ensure the safe integration of civil UASs into civilian airspace are available today. The extrapolation that can be made based on the above arguments is that advancement of UAS technologies will more likely have a significant bearing on the safe integration of UASs into civilian airspace. Therefore, as an identified research gap, the research/main objective of this research is to identify future technological factors affecting Unmanned Aircraft Systems in the Republic of South Africa leading towards the year 2025.
|
Page generated in 0.0528 seconds