The research objectives for this project were to explicitly define the anchor bolt corrosion problem in the state of Georgia and recommend action to the Georgia Department of Transportation. The bearing assembly of concern is the plate bearing assembly, in which carbon steel and/or bronze plates are anchored by either carbon steel or stainless steel anchor bolts. Inspection report data revealed that anchor bolt corrosion was ubiquitous for all environments in Georgia; the problem was reported for 27% of the steel girder bridges throughout the state. Based on a synthesis of the field investigations, bolt failure analyses, laboratory experimental testing, and review of GDOT inspection report surveys, the corrosion of carbon steel anchor bolts is caused universally by concentration cell corrosion. Other corrosion mechanisms of concern are galvanic and crevice corrosion, which are both enhanced by the current bearing design. Corrosion protection provided through zinc galvanization cannot sufficiently protect the carbon steel bolt for its entire service life. Corrosion potential and cyclic polarization data confirmed that ASTM Type 304, Type 316, Type 2101, and Type 2205 were protected from concentration cell and localized corrosion in the simulated bearing environment. Therefore, it is recommended that the stainless steel anchor bolts of these types be use in future designs and that the bolts should be electrically separated from all dissimilar metals using a Nylon or Teflon washer to prevent preferential corrosion of carbon steel. It is further recommended that the bronze lube plate should be eliminated entirely and that the bearing type should be a reinforced elastomeric bearing. Maintenance of existing sliding plate bearings should include regular cleaning by brushing away debris from the bearing surfaces, and bridges with carbon steel anchor bolts should be retrofitted to provide additional lateral restraint according to current maintenance procedures.

Various anchorage systems including both cast-in-place and post-installed anchors have been developed for fastening both non-structural and structural components to concrete structures. The need for increased flexibility in the design of new structures and strengthening of existing concrete structures has led to increased use of various metallic anchors in practice. Although millions of fasteners are used each year in the construction industry around the world, knowledge of the fastening technology remains poor. In a sustainable society, buildings and structures must, from time to time, be adjusted to meet new demands. Loads on structures must, in general, be increased to comply with new demands, and the structural components and the structural connections must also be upgraded. From the structural connection point of view, the adequacy of the current fastenings for the intended increased load must be determined, and inadequate fastenings must either be replaced or upgraded. The current design models are generally believed to be conservative, although the extent of this behavior is not very clear. To address these issues, the current models must be refined to allow the design of new fastenings and also the assessment of current anchorage systems in practice. The research presented in this thesis consists of numerical and experimental studies of the load-carrying capacity of anchors in concrete structures. Two different types of anchors were studied: (I) cast-in-place headed anchors, and (II) post-installed adhesive anchors. This research focused particularly on the tensile load-carrying capacity of cast-in-place headed anchors and also on the sustained tension loading performance of post-installed adhesive anchors. The overall objective of this research was to provide knowledge for the development of improved methods of designing new fastening systems and assessing the current anchorage systems in practice. For the cast-in-place headed anchors (I), the influence of various parameters including the size of anchor head, thickness of concrete member, amount of orthogonal surface reinforcement, presence of concrete cracks, concrete compressive strength, and addition of steel fibers to concrete were studied. Among these parameters, the influence of the anchor head size, member thickness, surface reinforcement, and cracked concrete was initially evaluated via numerical analysis of headed anchors at various embedment depths. Although these parameters have considerable influence on the anchorage capacity and performance, this influence is not explicitly considered by the current design models. The numerical results showed that the tensile breakout capacity of headed anchors increases with increasing member thickness and/or increasing size of the anchor head or the use of orthogonal surface reinforcement. However, their capacity decreased considerably in cracked concrete. Based on the numerical results, the current theoretical model for the tensile breakout capacity of headed anchors was extended by incorporating several modification factors that take the influence of the investigated parameters into account. In addition, a supplementary experimental study was performed to verify the numerically obtained findings and the proposed refined model. The experimental results corresponded closely to the numerical results, both in terms of failure load and failure pattern, thereby confirming the validity of the proposed model. The validity of the model was further confirmed through experimental results reported in the literature. Additional experiments were performed to determine the influence of the concrete compressive strength and the addition of steel fiber to concrete on the anchorage capacity and performance. These experiments showed that the anchorage capacity and stiffness increase considerably with increasing concrete compressive strength, but the ductility of the anchor decreases. However, the anchorage capacity and ductility increased significantly with the addition of steel fibers to the concrete mixture. The test results also revealed that the tensile breakout capacity of headed anchors in steel fiber-reinforced concrete is significantly underestimated by the current design model. The long-term performance and creep behavior of the post-installed headed anchors (II) was evaluated from the results of long-time tests on adhesive anchors under sustained loads. In this experimental study, adhesive anchors of various sizes were subjected to various sustained load levels for up to 28 years. The anchors were also exposed to several in-service conditions including indoor temperature, variations in the outdoor temperature and humidity, wetness (i.e., water on the surface of concrete), and the presence of salt (setting accelerant) additives in the concrete. Among the tested in-service conditions, variations in the outdoor temperature and humidity had the most adverse effect on the long-term sustained loading performance of the anchors. Based on the test results, recommendations were proposed for maximum sustained load levels under various conditions. The anchors tested under indoor conditions could carry sustained loads of up to 47% of their mean ultimate short-term capacities. However, compared with these anchors, the anchors tested under outdoor conditions exhibited larger creep deformation and failure occurred at sustained loads higher than 23% of their mean ultimate short-term capacities. Salt additives in concrete and wet conditions had negligible influence on the long-term performance of the anchors, although the wet condition resulted in progressive corrosion of the steel. Based on the experimental results, the suitability of the current testing and approval provisions for qualifying adhesive anchors subjected to long-term sustained tensile loads was evaluated. The evaluations revealed that the current approval provisions are not necessarily reliable for qualifying adhesive anchors for long-term sustained loading applications. Recommendations were given for modifying the current provisions to ensure safe long-term performance of adhesive anchors under sustained loads.

Diploma thesis includes design and examination of steel load-carrying structure. Construction includes car deal warehouse and car repair shop with extension for car varnishing. Car deal warehouse has ground dimensions 22 x 30 m and total high 10 m. Main frame is composed of Vierendeel trusses with arc shape. Car repair shop has ground dimensions 20 x 30 m and total high 10 m. Main frame is composed of truss girders and web-plate columns. Frame extension has ground dimension 20 x 10 m and total high 6,4 m. Cladding is composed of sandwich panels. Store´s gable wall and a part of the roof are glass. Climatic load is intended for locality Ostrava.