This work is focused on thermomechanical and electric analyses of microelectronic structures in the ANSYS program. Firstly an analysed model was formed in the program Solidworks. Then structures with components SOT23, SMD 1206, FlipChip and chip with wire bonding interconnection were analyzed. The analyses were performed for the temperatures 50, 100, 150 °C and various materials. The simulations outputs are presented as pictures in colours with models deformations and calculated values. The results will be utilised in education and presented on the web. The Flash, ActionScript and XML technologies were used for application to present results of the research.

The aim of the project was to prepare the given model of the current path in the environment of the SolidWorks programme, in order to simulate the flow path in the environment of the Ansys programme, where there was calculated the distribution of current density,voltage drops and heat loss on the the specified current track according to specified conditions. The obtained results are analyzed at the conclusion of this work.

The aim of the project was to get familiar with the environment of ANSYS CFX, create several models of fans and synchronous machine model in Autodesk inventor, create model of cooling medium flow through the machine with these fans and evaluation of results. Firstly the thesis describes the synchronous machine itself, losses of the machine, the flow of power of synchronous machine and methods of its cooling. Next the thesis describes each kind of heat transfer, laminar and turbulent flow. The thesis also refers of kind of the fans and the program used to calculate the flow Ansys CFX, including the method that Ansys used to calculate. The work describes the individual modification of fans and setting of calculation in ANSYS. Then displays the results of the analysis these fans for different numbers of fan blades and for modification of the fan. Then the thesis analyzes selected modifications due to changing speed. In the last chapter shows the analysis of flow in the machine with three different fans. In particular, there is shown the mass flow rate, pressure and its distribution on areas for evaluation.

ABSTRAKT Obsah této práce je směřován na řešení problematiky měření impedančních charakteristik dielektrických materiálů, zejména keramik, za pomocí simulace připojení elektrod na mě- řený vzorek. V práci je popsáno měření impedancí se zaměřením na metodu impedanční spektroskopie. Cílem práce je seznámení s problematikou měření komplexní impedance a popsání parazitních jevů, vyskytujících se v materiálu. Dále jsou v práci popisovány současné možnosti simulací a simulačních softwarů jako je zejména ANSYS Maxwell. S využitím simulací tohoto softwaru jsou v práci řešeny impedanční charakteristiky vodivé keramiky a jejich závislost na poloze napájecích elektrod. KLÍČOVÁ SLOVA Dielektrické materiály, elektrická polarizace, impedanční spektroskopie, komplexní impe- dance, vodivé keramiky, ANSYS, metoda konečných prvků. ABSTRACT Content of this thesis is aimed to solutions of issues, created due measurement impe- dance characteristics of dielectric materials, mainly ceramics, using simulation electrode position by specific software. In thesis is described impedance measurement with focusing to impedance spectroscopy. Goal of this thesis is to get acquainted with issues of mea- surement complex impedance and explain parasitics effects in ceramics material. Further goals of thesis are described current possibilities of simulation software ANSYS Ma- xwell. Using this simulation software was solved impedance characteristics of conductive ceramics and their dependence of electrodes position.

The present work deals with electron microscopy, electron microscopy primarily environmental. The main task of the work will draft the optimal shape of the differentially pumped chamber, dividing the pressure difference between tube and chamber with sample for a new concept of an electron microscope. By ANSYS Fluent will be analyzed pumping gas. Subsequently, according to the results obtained will be a modified form of the differential Chamber and to achieve the lowest gas pressure on the track of the electron beam.

This work deals with the issue of packaging and heat transfer. Especially this work focused on QFN and BGA packages. Nowadays most sophisticated conventional solution. First part deals with analysis of the current status of packages. Next part is analyze the issue of heat transfer in electronic systems. The following section is an experimental dealing with simulation in ANSYS Workbench and validation of these simulations by designed test structures. At the end is evaluated properties and behavior of these packages.

The thesis is focused on the calculation of electrodynamic forces that counterwork on moving contacts of compact circuit breaker BL1600 from the company OEZ Letohrad. The thesis is divided into separates chapters that build on themselves. In the introduction the reason why we deal with calculation of dynamic forces and structural arrangement of current carrying path is described. In the following chapter there is a theoretical analysis of electrodynamic forces that conterwork on individual parts of circuit breaker´s element. The third part is devoted to structural arrangement of the circuit breaker BL1600. In this part we can find an example of using the circuit broker Modeion in practice. Two next chaptures deal with adjustment of the model of current carrying path which then serves for the calculation of electrodynamic forces. The rest of the thesis is devoted to my own calculations. These calculations are mainly stationary where we try to find the forces that conterwork on the contacts in a steady current and in a point in time. There are also dynamics calculation when we can watch the forces that counterwork on contacts in a certain time interval. The last chapter is devoted to a stationary calculation of forces that counterwork on the electrical arc which arises while turning the short-circuit current off. The obtained results are evaluated in partial conclusions of this thesis.

This master´s thesis discusses the analysis of the shape of the intake ports of differentially pumped chamber for the current concept. The first part is an introduction to the microscopy issue, then it is focused on ESEM microscopes and it also includes a describtion of the Flow dynamics and a mathematical describtion. In the following chapters the software Solid Works, where the model of differentially pumped chamber is created, and the software Ansys Fluent, which is used for analysis, are described. The second part concerns the proposed concepts and the results of their simulations. At the end of the work the results are analyzed and evaluated.

Create finite elements model ( FEM ) for solution direct stress of bend by ANSYS. Analyze calculated stress and deflextion, compare with results by simple manually-operated calculation. Extremes of these quantities compare with results by encoded rule.

The purpose of this thesis is to study behaving of thin reinforced concrete shell structure with a huge span which overcomes two hundred meters. The main goal is to find an ideal shape of such structure to ensure only compression without bending tension which allows us to cover huge area with a very thin shell. For solution of internal forces was used the finite elemet method (ANSYS).The blueprints of shape of this shell are the part of this project.