No description available.

Low temperature cracking is attributed to tensile stresses induced in an asphalt concrete pavement that develop when the pavement is subjected to a cold temperature. Cracking results in poor ride quality and a reduction in service life of the pavement. Low temperature cracking has been predicted by regression equations, mechanistic approaches and by simulation measurements. The purpose of the study reported herein is to (1) evaluate the Thermal Stress Restrained Specimen Test (TSRST) as an accelerated performance test to simulate low temperature cracking of asphalt concrete mixtures and (2) develop a deterministic and probabilistic model to predict low temperature cracking with TSRST results. Construction histories, cracking observations and temperature data were collected for five test roads in Alaska, Pennsylvania and Finland. A full scale and fully controlled low temperature cracking test program was conducted at the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL). Specimens were fabricated in the laboratory with original asphalt cements and aggregates from the test roads. In addition, asphalt concrete pavement specimens were cut from the test sections. The TSRST results obtained for these samples were correlated with the field observations. Based on a statistical analysis of the data, the TSRST fracture temperature is associated with the field cracking temperature and crack frequency for the test roads where mixture properties dominated low temperature cracking. It was concluded that the TSRST can be used to simulate low temperature cracking of asphalt concrete mixtures. A deterministic and a probabilistic model were developed to predict crack spacing as a function of time using the TSRST results, pavement thickness and bulk density, pavement restraint conditions and air temperature. The affect of aging on pavement properties was incorporated in the models by predicting the field aging with Long Term Oven Aging (LTOA) treatment in the laboratory. The calculation of the crack spacing is based on the theory that the pavement slab cracks when the pavement temperature reaches the cracking temperature of the mixture and the slab is fully restrained. The deterministic model predicts crack spacing with time whereas the probabilistic model predicts crack spacing and its variation with time and yields the reliability of the design with regard to a minimum acceptable crack spacing criterion defined by road authorities. The models were verified by comparing the predicted crack spacings for the five test roads to the observed crack spacings. The probabilistic model is recommended for use in predicting the low temperature cracking of asphalt concrete mixtures. / Graduation date: 1994

Thesis (M.S.)--University of Nevada, Reno, 2008. / "May, 2008." Includes bibliographical references (leaves 155-160). Online version available on the World Wide Web.

Call number: LD2668 .T4 1962 C37

Asphalt concrete mix design methods, such as the Marshall method, have historically been based on physical and phenomenological material testing empirically correlated to observed field performance. Changing pavement field state conditions such as increased trucking, poorer quality aggregate resources, and the aged state of road infrastructure in Saskatchewan have resulted in recent pavement performance to be outside traditional empirical performance prediction inference. <p>It has been recognized worldwide that a mechanistic based asphalt concrete mix design methodology that directly quantifies structural behaviour of pavement under diverse field state conditions could significantly assist pavement design engineers. However, SHRP Level II and III mechanistic asphalt concrete characterization has been shown not to be pragmatic for characterizing asphalt concrete mixes. <p>The objective of this research was to investigate the use of mechanistic material properties obtained from triaxial frequency sweep characterization in the rapid triaxial tester (RaTT) in conjunction with SHRP gyratory compaction properties for designing asphalt concrete for different asphalt cement contents, traffic loads, traffic speeds, and temperatures. <p>RaTT testing was more responsive to variation in asphalt cement content outside of acceptable ranges of volumetric properties relative to Marshall stability and flow. This demonstrated the importance of specifying acceptable volumetric properties of asphalt concrete mixes. Correlation of material properties with volumetric measurements validated triaxial frequency sweep characterization in the RaTT. Dynamic modulus, Poissons ratio, and phase angle results were in accordance with expected material behaviour, indicating that the RaTT provides reasonable asphalt concrete material properties. Also, the RaTT identified asphalt concrete to be a nonlinear viscoelastic material, as observed in the field. <p>The RaTT was able to characterize SHRP gyratory compacted samples for the typical range of traction states, load frequencies, and temperatures that simulated a range of Saskatchewan field state conditions. Triaxial frequency sweep testing in the RaTT could significantly augment conventional volumetric mix analysis as well as the SHRP SuperpaveTM Level I asphalt concrete mix design system. RaTT testing was found to be cost effective, time efficient, and provided mechanistic material constitutive relations that can be employed for inelastic mechanistic mix design, road structural modelling, and asset management.

Asphalt concrete mix design methods, such as the Marshall method, have historically been based on physical and phenomenological material testing empirically correlated to observed field performance. Changing pavement field state conditions such as increased trucking, poorer quality aggregate resources, and the aged state of road infrastructure in Saskatchewan have resulted in recent pavement performance to be outside traditional empirical performance prediction inference. <p>It has been recognized worldwide that a mechanistic based asphalt concrete mix design methodology that directly quantifies structural behaviour of pavement under diverse field state conditions could significantly assist pavement design engineers. However, SHRP Level II and III mechanistic asphalt concrete characterization has been shown not to be pragmatic for characterizing asphalt concrete mixes. <p>The objective of this research was to investigate the use of mechanistic material properties obtained from triaxial frequency sweep characterization in the rapid triaxial tester (RaTT) in conjunction with SHRP gyratory compaction properties for designing asphalt concrete for different asphalt cement contents, traffic loads, traffic speeds, and temperatures. <p>RaTT testing was more responsive to variation in asphalt cement content outside of acceptable ranges of volumetric properties relative to Marshall stability and flow. This demonstrated the importance of specifying acceptable volumetric properties of asphalt concrete mixes. Correlation of material properties with volumetric measurements validated triaxial frequency sweep characterization in the RaTT. Dynamic modulus, Poissons ratio, and phase angle results were in accordance with expected material behaviour, indicating that the RaTT provides reasonable asphalt concrete material properties. Also, the RaTT identified asphalt concrete to be a nonlinear viscoelastic material, as observed in the field. <p>The RaTT was able to characterize SHRP gyratory compacted samples for the typical range of traction states, load frequencies, and temperatures that simulated a range of Saskatchewan field state conditions. Triaxial frequency sweep testing in the RaTT could significantly augment conventional volumetric mix analysis as well as the SHRP SuperpaveTM Level I asphalt concrete mix design system. RaTT testing was found to be cost effective, time efficient, and provided mechanistic material constitutive relations that can be employed for inelastic mechanistic mix design, road structural modelling, and asset management.

This thesis studies the mechanics which can be associated with asphalt concrete compaction and develops continuum models in a general thermo-mechanical setting which can be used in future work to corroborate experimental compaction experiment results. Modeling asphalt concrete compaction, and also the ability to thereby predict response of mixes, is of great importance to the pavement industry. Asphalt concrete exhibits nonlinear response even at small strains and the response of asphalt concrete to different types of loading is quite different. The properties of asphalt concrete are highly influenced by the type and amount of the aggregates and the asphalt used. The internal structure of asphalt concrete continues to evolve during the loading process. This is due to the influence of different kinds of activities at the micro-structure level and to the interactions with the environment. The properties of asphalt concrete depend on its internal structure. Hence, we need to take into account the evolution of the internal structure in modeling the response of asphalt concrete. A theoretical model has been developed using the notion of multiple natural configurations to study a variety of non-linear dissipative responses of real materials. By specifying the forms for the stored energy and the rate of dissipation function of the material, a specific model was developed using this framework to model asphalt compaction. A compressible model is developed by choosing appropriate forms of stored energy and rate of dissipation function. Finally, a parametric study of the model is presented for a simple compression deformation. It is anticipated that the present work will aid in the development of better constitutive equations which in turn will accurately model asphalt compaction both in laboratory and in field. Distinct numerical approaches have been used to demonstrate the applicability of the theoretical framework to model material response of asphalt.

Thesis (Ph. D.)--Rutgers University, 2009. / "Graduate Program in Civil and Environmental Engineering." Includes bibliographical references (p. 194-197).

In this report a relationship is established between the variables of compaction temperature, compaction effort, mixture gradation and, density, air void content and stability of asphalt mixtures. The Marshall method of mix design was used, and Vibratory Kneading Compactor was utilized for compaction. Results include Marshall Stability and density-air void analysis for 4 and 6-inch specimens. It was found that the densities generally increased with increase of compaction temperatures and compaction efforts. From selected sets of 6-inch specimens, 4-inch cores were obtained. Density and stability studies were carried out on these cores and the results obtained were found to have the same trends. The air void content and voids in the mineral aggregates decreased with the increase of compaction effort. Stability increased with the increase in density. All the results found, indicate strong effects of compaction temperature and compactive effort on the amount of air voids, VMA, density, and stability of the mixes used.

No description available.