The main objective for the work described in this PhD thesiswas to formulate a friction model to characterize thefrictional behavior of paper. More specifically, the modelshould explain a phenomenon that is typical for paper grades,viz.: that the level of paper-to-paper friction is dependent onthe direction and the number of previous slides. The modelshould also explain the lubricating effect oflow-molecular-mass lipophilic compounds (LLC) that occur inpaper on paper-to-paper friction. Furthermore, the model shoulddescribe the types of forces that influence paper-to-paperfiction and explain the mechanism by which the LLC decreasepaper-to-paper friction. This thesis consists of a literature review of the basicconcepts of tribology and a summary of the main results andconclusions from four studies on the frictional characteristicsof paper and a study on the friction and adhesion of cellulosesurfaces together with some unpublished material. The purpose of the investigation described in the firstpaper was to explain a phenomenon that is typical for papergrades, viz.: the level of paper-to-paper friction is dependenton the direction and the number of previous slides. Thisbehavior is called“friction hysteresis”by theauthors, and it has its origin in the reorientation of thefibers on the surface of a paper and their alignment relativeto the sliding direction. The second paper describes a study that was aimed atidentifying lubricants that occur natively in paper. Filterpapers were impregnated with model compounds representing woodextractives, i.e. low-molecular-weight lipophilic compounds,which are present in wood, pulp and paper, and thepaper-to-paper friction was determined. The results of thatstudy show that a wood extractive must fulfill severalstructural criteria in order to lubricate a paper surface: Itmust have a hydrophilic group that can attach to the papersurface and a linear hydrocarbon backbone of sufficientlength. Although it is not specifically stated in the second paper,the authors proposed a type of lubrication by which woodextractives decrease paper-to-paper friction that is, ineffect, boundary lubrication. The purpose of the investigationdescribed in the third paper was to clarify whether woodextractives and other low-molecular-mass lipophilic compoundsthat occur in paper can act as boundary lubricants on papersurfaces. The main objective of that study was to investigatethe role of chemical structure of LLC for their orientationrelative to the paper surface, which is an important criterionfor boundary lubrication. Filter papers were impregnated withmagnesium salts of different lipophilic acids, which were usedfor model compounds for the LLC. The deposited layers ofmagnesium salts were characterized by X-ray photoelectronspectroscopy (XPS) and contact angle goniometry and thefriction of the impregnated paper sheets was determined. Theresults show that the degree of lubrication and the resistanceto wear of the layers of a magnesium salt increased withincreasing chain length and increasing degree of linearity ofthe lipophilic acid. Based on the results of that study and ofearlier studies, it is concluded that boundary lubrication isthe type of lubrication by which low-molecular-mass lipophiliccompounds that occur natively in paper decreasepaper-to-paper-friction. In boundary lubrication, surfaces are covered withmonolayers of lubricant molecules that comprise an active headgroup that can attach to the surface, e.g. a carboxyl group,and an inert linear backbone, such as a long saturatedhydrocarbon chain. Such compounds form ordered monolayers onsurfaces, so that the backbone points vertically out of planeof the surface. The friction is then determined by theinteractions between the monolayers, which are weaker than theinteractions between the clean surfaces and this gives a lowerfriction. The fourth paper describes a study on the origin of thedifferences in friction levels between different linerboardsbased on recycled fiber (old corrugated container, OCC). Thesheets were subjected to two extraction stages and analyzedwith respect to surface roughness and their content oflow-molecular-mass lipophilic compounds (LLC). The resultsshowed that a high amount of LLC in the sheets lead to lowfriction, due to lubrication. The fifth paper describes a study that was aimed atdetermining the types of forces that influence the frictionbetween the surfaces of hydrophilic polymers and explaining themechanism by which boundary lubricants decrease the friction.The adhesion and the friction of model systems was measuredwith atomic force microscopy (AFM) using regenerated cellulosefilms and functionalised AFM tips and the effect of fatty acidsand humidity was investigated. The friction significantlyincreased with increasing humidity and that there was a strongcorrelation between the ability of a fatty acid to form ahydrophobic surface and its lubricating performance. Measuredadhesion forces at high humidity were well predicted bytheoretical models that took into account the effect of theLaplace pressure acting in a water meniscus formed aroundcontact regions due to capillary condensation. The resultsindicated that the degree of capillary condensation may beeffectively suppressed by increasing the hydrophobicity of thecontacting surfaces, causing adhesion and friction to decrease.These results suggest that friction between paper surfacesunder ambient conditions is greatly influenced by the degree ofcapillary condensation. Furthermore, lubrication by fatty acidsis achieved by the formation of a vertically oriented,hydrophobic monolayer that can withstand the stresses duringsliding and increase the hydrophobicity of the paper surfaceand thereby suppress capillary condensation. <b>Keywords:</b>Friction, paper-to-paper friction, frictionhysteresis, fibers, orientation, sliding direction, woodextractives, low-molecular-mass lipophilic compounds, boundarylubrication, adhesion, capillary condensation, Laplacepressure, surface forces, JKR theory, gas chromatography-massspectroscopy, X-ray photoelectron spectroscopy, contact angle,atomic force microscopy

This thesis examines the formation of Polyelectrolyte Multilayers (PEM) on cellulose fibres as a new way of influencing the fibre surface and the adhesion between wood fibres. The aim of the study was to enhance the fundamental understanding of the adsorption mechanisms behind the formation of Polyelectrolyte Multilayers on cellulose fibres; to study how the properties of the layers can be influenced and to show how the properties of the layers influence the adhesion between the fibres and the strength of paper sheets made from the PEM treated fibres. Different polyelectrolyte systems are known to form PEMs with different properties, and in this work two different polymer systems were extensively studied: poly(dimethyldiallylammonium chloride) (PDADMAC) / poly(styrene sulphonate) (PSS), which are both strong polylectrolytes (i.e. are highly charged over a wide range of pH) and poly allylaminehydrochloride (PAH) /poly acrylic acid (PAA), which are both weak polyelectorlytes (i.e. sensitive to pH changes). PEMs were also formed from PAH/ poly(3,4-ethylenedioxythiophene):PSS (PEDOT:PSS), in order to form electrically conducting PEMs on fibres and PEM-like structures were formed from polyethylene oxide (PEO) and polyacrylic acid (PAA). In order to study the influence of the PEM on adhesion and paper strength, fibres were treated and used to form sheets which were physically tested according to determine the tensile index and strain at break. Both these systems were studied using different molecular mass fractions. High molecular mass PDADMAC/PSS (&gt;500k/1000k) had a significantly greater influence as a function of the number of layers than low molecular mass PDADMAC/PSS (30k/80k). In contrast, sheets made from high molecular mass PAH/PAA (70k/240k) showed a significantly lower increase in strength than sheets made from low molecular PAH/PAA investigated earlier. Both these systems had a greater influence on paper strength when the cationic polyelectrolyte was adsorbed in the outermost layer. The amount of polyelectrolytes adsorbed on the fibres was determined using polylectrolyte titration (PET) and destructive analytical methods. Adsorption to model surfaces of silicon oxide was studied before the adsorption on fibres, in order to understand the influence on PEM properties of parameters such as salt concentration and adsorption time. Adhesion studies of surfaces coated with PAH/PAA using AFM, showed an increase in adhesion as a function of the number of adsorbed layers. The adhesion was higher when PAH was adsorbed in the outermost layers. Individual fibres were also partly treated using a Dynamic Contact Angle analyser (DCA) and were studied with regard to their wettability. In general, the wettability was lower when the cationic polymer was outermost. The level of adhesion and paper strength are discussed in terms of rigidity and wettability and the PEMs demonstrating a large number of free chain ends, a large chain mobility and a low wettability was found to have the greatest influence to adhesion and paper strength. / QC 20100823

Hydrophobic interactions guide important molecular self-assembly processes such as protein folding. On the macroscale, hydrophobic interactions consist of the aggregation of "oil-like" objects in water by minimizing the interfacial energy. However, the hydration mechanism of small hydrophobic molecules on the nanoscale (~1 nm) differs fundamentally from its macroscopic counterpart. Theoretical studies over the last two decades have pointed to an intricate dependence of molecular hydration mechanisms on the length scale. The microscopic-to-macroscopic cross-over length scale is critically important to hydrophobic interactions in polymers, proteins and other macromolecules. Accurate experimental determination of hydration mechanisms and their interaction strengths are needed to understand protein folding. This thesis reports the development of experimental and analytical techniques that allow for direct measurements of hydrophobic interactions in a single molecule. Using single molecule force spectroscopy, the mechanical unfolding of a single hydrophobic homopolymer was identified and modeled. Two experiments examined how hydrophobicity at the molecular scale differ from the macroscopic scale. The first experiment identifies macroscopic interfacial tension as a critical parameter governing the molecular hydrophobic hydration strength. This experiment shows that the solvent conditions affect the microscopic and macroscopic hydrophobic strengths in similar ways, consistent with theoretical predictions. The second experiment probes the hydrophobic size effect by studying how the size of a non-polar side-chain affects the thermal signatures of hydration. Our experimental results reveal a cross-over length scale of approximately 1 nm that bridges the transition from entropically driven microscopic hydration mechanism to enthalpically driven macroscopic hydration mechanism. These results indicate that hydrophobic interactions at the molecular scale differ from macroscopic scale, pointing to potential ways to improve our understanding and predictions of molecular interactions. The system established in this thesis forms the foundation for further investigation of polymer hydrophobicity.

Segmental long spacing (SLS) collagen self-assembly was studied by analyzing aggregates formed from different nucleoside triphosphates at various protonation stages. Triple-negatively charged triphosphate groups were determined to be critical for SLS assembly, electrostatically bridging basic residues between collagen monomers. In the second part of this thesis, the nominal elastic modulus for each of the three forms of Type I collagen aggregate was measured and compared. Fibrous long spacing collagen, often associated with diseased tissues, exhibited lower stiffness in comparison to the other forms, native and SLS, suggesting decreased structural stability in diseased tissues. In the last section, a unidirectional pattern of native fibrils was assembled using mica as a template; the ability to customize and change the surface morphology was also demonstrated. For the first time, collagen monomers deposited on the mica were demonstrated to gain lateral mobility.

Segmental long spacing (SLS) collagen self-assembly was studied by analyzing aggregates formed from different nucleoside triphosphates at various protonation stages. Triple-negatively charged triphosphate groups were determined to be critical for SLS assembly, electrostatically bridging basic residues between collagen monomers. In the second part of this thesis, the nominal elastic modulus for each of the three forms of Type I collagen aggregate was measured and compared. Fibrous long spacing collagen, often associated with diseased tissues, exhibited lower stiffness in comparison to the other forms, native and SLS, suggesting decreased structural stability in diseased tissues. In the last section, a unidirectional pattern of native fibrils was assembled using mica as a template; the ability to customize and change the surface morphology was also demonstrated. For the first time, collagen monomers deposited on the mica were demonstrated to gain lateral mobility.

<p>This study is focused on designing and characterizing protein-based building blocks in order to construct self-assembled nano-structured biomaterials. In detail, this research aims to: (1) investigate a new class of proteins that possess nanospring behaviors at a single-molecule level, and utilize these proteins along with currently characterized elastomeric proteins as building blocks for nano-structured biomaterials; (2) develop a new method to accurately measure intermolecular interactions of self-assembling two or more arbitrary (poly)peptides, and select some of them which have appropriate tensile strength for crosslinking the proteins to construct elastomeric biomaterials; (3) construct well-defined protein building blocks which are composed of elastomeric proteins terminated with self-oligomerizing crosslinkers, and characterize self-assembled structures created by the building blocks to determine whether the elasticity of proteins at single-molecule level can be maintained.</p><p>Primary experimental methods of this research are (1) atomic force microscope (AFM) based single-molecule force spectroscopy (SMFS) that allows us to manipulate single molecules and to obtain their mechanical properties such as elasticity, unfolding and refolding properties, and force-induced conformational changes, (2) AFM imaging that permits us to identify topology of single molecules and supramolecular structures, and (3) protein engineering that allows us to genetically connect elastomeric proteins and self-assembling linkers together to construct well-defined protein building blocks.</p><p>Nanospring behavior of á-helical repeat proteins: We revealed that á-helical repeat proteins, composed of tightly packed á-helical repeats that form spiral-shaped protein structures, unfold and refold in near equilibrium, while they are stretched and relaxed during AFM based SMFS measurements. In addition to minimal energy dissipation by the equilibrium process, we also found that these proteins can yield high stretch ratios (>10 times) due to their packed initial forms. Therefore, we, for the first time, recognized a new class of polypeptides with nanospring behaviors. </p><p>Protein-based force probes for gauging molecular interactions: We developed protein-based force probes for simple, robust and general AFM assays to accurately measure intermolecular forces between self-oligomerization of two or more arbitrary polypeptides that potentially can serve as molecular crosslinkers. For demonstration, we genetically connected the force probe to the Strep-tag II and mixed it with its molecular self-assembling partner, the Strep-Tactin. Clearly characterized force fingerprints by the force probe allowed identification of molecular interactions of the single Strep-tag II and Strep-Tactin complex when the complex is stretched by AFM. We found a single energy barrier exists between Strep-tag II and Strep-Tactin in our given loading rates. Based upon our demonstration, the use of the force probe can be expanded to investigate the strength of interactions within many protein complexes composed of homo- and hetero-dimers, and even higher oligomeric forms. Obtained information can be used to choose potential self-assembling crosslinkers which can connect elastomeric proteins with appropriate strength in higher-order structures. </p><p>Self-assembled nano-structured biomaterials with well-defined protein-based building blocks: We constructed well-defined protein building blocks with tailored mechanical properties for self-assembled nano-structured materials. We engineered protein constructs composed of tandem repeats of either a I27-SNase dimer or a I27 domain alone and terminated them with a monomeric streptavidin which is known to form extremely stable tetramers naturally. By using molecular biology and AFM imaging techniques, we found that these protein building blocks transformed into stable tetrameric complexes. By using AFM based SMFS, we measured, to our knowledge for the first time, the mechanical strength of the streptavidin tetramer at a single-molecule level and captured its mechanical anisotropy. Using streptavidin tetramers as crosslinkers offers a unique opportunity to create well-defined protein based self-assembled materials that preserve the molecular properties of their building blocks.</p> / Dissertation

In this study, we have investigated the effect of substrate temperature, use of adhesive layer, deposition rate, annealing and substrate prebaking on the morphology of gold films deposited onto quartz surfaces. For the film growth, physical vapor deposition methods namely electron beam and thermal depositions have been used. Surface morphology of the films have been characterized with atomic force microscopy. Our aim was to confirm the general trends observed for these parameters in our evaporator system for a limited working range in order to produce gold films which are suitable to be used simultaneously for quartz crystal microbalance and helium atom diffraction measurements. At the end of this study, we confirmed the general trends regarding the effect of these parameters stated in literature except annealing process. We obtained a minimum 170 nm2 atomically flat surface with a roughness value smaller than 0.200 nm by thermal deposition method.

An alkyl-containing self-assembled monolayer is grafted on the silicon surface by a nature process in solutions. The alkyl thin film was used as the lubricant for the silica interface, usually applied to the MEMS or NENS domains. The ability of reducing friction for silica device at room temperature was improved, but little was known as the thin films existed at higher temperature during device was working or operating. In this study, we used Hexyltrichlorosilane (C6), Dodecyltrichlorosilane (C12), and Octadecyltrichlorosilane (C18) molecules to form self-assembled monolayers (SAMs) on silicon, and these monolayers exhibited different molecular packing properties due to different interactions between the molecules. Fourier transform infrared spectroscopy (FTIR) revealed that the short chain-length (C6) molecules exhibited poor packing on the surface at room temperature, and that the molecular packing of C6 was thermally stable up to 500 K. But the C12 and C18 monolayers exhibited abrupt blue shifts in FTIR at temperatures between 300 and 575 K, with stable packing observed over several temperature ranges. Furthermore, water contact angle measurements showed the C6, C12, and C18 molecular films changed from hydrophobic to hydrophilic as the sample temperature was increased. Atomic force microscopy (AFM) images revealed that pits had formed in the C18 monolayer after the temperature was increased to 460 K, which were caused by the molecular reorganization of C18 on the surface. This resulted in an abrupt change in the friction coefficient for the C18 monolayer at 460K as compared to the short C6 and C12 monolayers. However, the friction coefficients for all the SAM films still increased with temperature. Understanding the temperature-dependent behavior of SAM film molecules will assist in the design of better anti-wear monolayers to improve performance and increase lifetimes in modern MEMS and NEMS devices.

Combined atomic force microscopy-scanning electrochemical microscopy (AFM-SECM) is capable of providing simultaneous topographical and electrochemical imaging at sample surfaces. Integration of amperometric biosensors at tip-integrated electrodes recessed from the apex of the AFM tip further enhances the versatility of such bifunctional probes. Of particular interest to this work was the detection of adenosine triphosphate (ATP) at a cellular level, since ATP is involved in many biologically relevant processes. There are challenges concerning the integration of biosensors into bifunctional AFM-SECM probes. This thesis focuses on addressing and advancing several of these limitations. Thin insulation layers are important for AFM-SECM based applications to enhance AFM and SECM performance. Plasma-polymerized fluorocarbon membranes are introduced as novel thin film insulation materials for AFM-SECM probes. Insulation layers with a thickness of < 300 nm were found to exhibit excellent insulating properties and satisfying temporal stability for successful application in AFM-SECM experiments. Furthermore new approaches for increasing the electrode area in conventionally focused ion beam (FIB) fabricated AFM-SECM probes were implemented, since enhancement of the current response in conjunction with biosensing experiments is required. Ion beam induced deposition (IBID) was used to generate platinum carbon (PtC) deposits at AFM-SECM probes, thereby successfully increasing the tip-integrated electrode area. PtC composites were thoroughly characterized in terms of their physical and electrochemical properties. Since a high carbon fraction in the PtC composite was inhibiting the charge transfer kinetics at the electrode surface for certain analytes, several pre-treatment strategies were investigated including annealing, UV/ozone treatment, and FIB milling. FIB milling proved to be the most promising procedure improving charge transfer properties at the electrode along with fabrication compatibility at AFM-SECM probes. The last part of this thesis aimed at providing fundamental studies on AFM-SECM application at live epithelial cell monolayers. AFM was used in different imaging modes to characterize the topography of epithelial cells. ATP detection at epithelial cells was achieved with amperometric biosensors combined with non-invasive SECM. Biosensors were further miniaturized at batch-fabricated AFM-SECM probes enabling laterally-resolved detection of ATP at epithelial cells. Additionally, PtC composite materials were evaluated for applicability as transducer platforms for enzymatic biosensors.

This dissertation focuses on quantitative subsurface and mechanical properties imaging potential of AFM probes. Extensive modeling of AFM probes are presented for thorough understanding of capabilities and limitations of current techniques, these models are verified by various experiments, and different methods are developed by utilizing force-sensing integrated read-out active tip (FIRAT), which is an active AFM probe with broad bandwidth. For quantitative subsurface imaging, a 3-D FEA model of AFM tip-sample contact is developed and this model can simulate AFM tip scan on nanoscale-sized buried structures. FIRAT probe, which is active and broadband, is utilized for interaction forces imaging during intermittent contact mode and mechanical characterization capability of this probe is investigated. It is shown that probe dynamics, stiffness, stiffness ambiguity, assumed contact mechanics, and noise are important parameters for the accuracy of mechanical properties imaging. An active tip control mechanism is introduced to limit contact forces during intermittent contact mode. In addition to these, a combined ultrasonic AFM and interaction forces imaging method is developed and modeled to solve the reduced elasticity measurement sensitivity on composite materials. This method is capable of imaging a broader range of elasticity on combination samples such as metal nanoparticles in polymers at nanoscale.