Spelling suggestions: "subject:"lack diffusion"" "subject:"back diffusion""
1 |
Reducing Ultra-High-Purity (UHP) Gas Consumption by Characterization of Trace Contaminant Kinetic and Transport Behavior in UHP Fabrication EnvironmentsDittler, Roy Frank January 2014 (has links)
Trends show that the fraction of the world's population with electronic devices using modern integrated circuits is increasing at a rapid rate. To meet consumer demands: less expensive, faster, and smaller electronics; while still making a profit, manufacturers must shrink transistor dimensions while increasing the number of transistors per integrated circuit; a trend predicted by Gorden E. Moore more than 44 years prior. As CMOS transistors scale down in size, new techniques such as atomic-layer deposition (ALD) are used to grow features one atomic layer at a time. ALD and other manufacturing processes are requiring increasingly stringent purities of process gases and liquids in order to minimize circuit killing defects which reduces yield and drives up manufacturing cost. Circuit killing defects caused by impurity incursions into UHP gas distribution system can come from a variety of sources and one of the impurity transport mechanisms investigated was back diffusion; the transport of impurities against convective flow. Once impurity incursions transpire, entire production lines are shut down and purging with UHP gas is initiated; a process that can take months thus resulting in tens of millions of dollars in lost revenue and substantial environment, safety, and health (ESH) impacts associated with high purge gas consumption. A combination of experimental investigation and process simulation was used to analyze the effect of various operational parameters on impurity back diffusion into UHP gas distribution systems. Advanced and highly sensitive analytical equipment, such as the Tiger Optics MTO 1000 H2O cavity ring-down spectrometer (CRDS), was used in experiments to measure real time back diffusing moisture concentrations exiting an electro-polished stainless-steel (EPSS) UHP distribution pipe. Design and operating parameters; main and lateral flow rates, system pressure, restrictive flow orifice (RFO) aperture size, and lateral length were changed to impact the extent of back diffusing impurities from a venting lateral. The process model developed in this work was validated by comparing its predictions with data from the experiment test bed. The process model includes convection, molecular diffusion in the bulk, surface diffusion, boundary layer transport, and all modes of dispersion; applicable in both laminar and turbulent flow regimes. Fluid dynamic properties were directly measured or were obtained by solving Navier-Stokes and continuity equations. Surface diffusion as well as convection and dispersion in the bulk fluid played a strong role in the transport of moisture from vents and lateral branches into the main line. In this analysis, a dimensionless number (Peclet Number) was derived and applied as the key indicator of the relative significance of various transport mechanisms in moisture back-diffusion. Guidelines and critical values of Peclet number were identified for assuring the operating conditions meet the purity requirements at the point of use while minimizing UHP gas usage. These guidelines allowed the determination of lateral lengths, lateral diameters, flow rates, and restrictive flow device configurations to minimize contamination and UHP gas consumption. Once a distribution system is contaminated, a significant amount of purge time is required to recover the system background due to the strong interactions between moisture molecules and the inner surfaces of the components in a gas distribution system. Because of the very high cost of UHP gases and factory downtime, it is critical for high-volume semiconductor manufacturers to reduce purge gas usage as well as purge time during the dry-down process. The removal of moisture contamination in UHP gas distribution systems was approached by using a novel technique dubbed pressure cyclic purge (PCP). EPSS piping was contaminated with moisture, from a controlled source, and then purged using a conventional purge technique or a PCP technique. Moisture removal rates and overall moisture removal was determined by measuring gas phase moisture concentration in real time via a CRDS moisture analyzer. When compared to conventional purge, PCP reduced the time required and purge gas needed to clean the UHP gas distribution systems. However, results indicate that indiscriminately initiating PCP can have less than ideal or even detrimental results. An investigation of purge techniques on the removal of gas phase, chemisorbed, and physisorbed moisture, coupled with the model predictions, led to the testing of hybrid PCP. The hybrid PCP approach proved to be the most adaptable purge technique and was used in next phase of testing and modeling. Experiments and modeling progressed to include testing the effectiveness of hybrid PCP in systems with laterals; more specifically, laterals that are "dead volumes" and results show that hybrid PCP becomes more purge time and purge gas efficient in systems with increasing number and size of dead volumes. The process model was used as a dry-down optimization tool requiring inputs of; geometry and size, temperature, starting contamination level, pressure swing limits of inline equipment, target cleanliness, and optimization goals; such as, minimizing pure time, minimizing purge gas usage, or minimizing total dry-down cost.
|
2 |
Water management in novel direct membrane deposition fuel cells under low humidificationBreitwieser, Matthias, Moroni, Riko, Schock, Jonathan, Schulz, Michael, Schillinger, Burkhard, Pfeiffer, Franz, Zengerle, Roland, Thiele, Simon 27 October 2020 (has links)
Polymer electrolyte membrane fuel cells (PEMFCs) fabricated by direct membrane deposition (DMD) were shown to work even at dry conditions without significant deterioration of the membrane resistance. Here, in situ neutron radiography is used to investigate the water management in those fuel cells to uncover the phenomena that lead to the robust operation under low humidification. A constant level of humidification within the membrane electrode assembly (MEA) of a DMD fuel cell is observed even under dry anode operation and 15% relative humidity on the cathode side. This proves a pronounced back diffusion of generated water from the cathode side to the anode side through the thin deposited membrane layer. Over the entire range of polarization curves a very high similarity of the water evolution in anode and cathode flow fields is found in spite of different humidification levels. It is shown that the power density of directly deposited membranes in contrast to a 50 μm thick N-112 membrane is only marginally affected by dry operation conditions. Water profiles in through-plane direction of the MEA reveal that the water content in the DMD fuel cell remains steady even at high current densities. This is in contrast to the N-112 reference fuel cell which shows a strong increase in membrane resistance and a reduced MEA water content with raising current densities. Thus this new MEA fabrication technique has a promising perspective, since dry operation conditions are highly requested in order to reduce fuel cell system costs.
|
3 |
Étude des Mécanismes de Transfert des Nanoparticules au travers d'une Barrière de Confinement Dynamique / Study of transfer mechanism of nanoparticles across a dynamical air barrierCésard, Vincent 16 November 2012 (has links)
Les travaux de thèse ont permis de quantifier l'efficacité de confinement de deux dispositifs distincts (un poste de sécurité microbiologique et une sorbonne classique) lors de la production simultanée de nanoaérosols et d'un gaz traceur (SF6). Deux techniques de mesure différentes ont été exploitées : la première basée sur la mesure de la distribution granulométrique de l'aérosol s'échappant (SMPS-C), l'autre reposant sur la détection de fluorescence d'échantillons prélevés (fluorescéine sodée utilisée comme marqueur des nanoparticules). Les résultats ont permis d'établir une forte corrélation entre le comportement d'un nanoaérosol et celui d'un gaz traceur lorsqu'ils sont émis simultanément dans une enceinte ventilée. Plus encore, on a observé une rétrodiffusion gazeuse quasiment deux fois plus importante pour le gaz traceur que pour les nanoparticules testées dans différentes configurations. Le dépôt ainsi que l'agglomération présents dans le cas du transport d'un nuage de nanoparticules peuvent expliquer ces écarts dans le niveau global de confinement obtenu. Cependant, ce constat n'est pas un gage de protection suffisante dans la mesure où il n'existe pas de valeur spécifique de référence lors de l'exposition à des nanoparticules. Il est alors utile de respecter les règles de bonne conduite qui ont été définies dans de nombreux guides INRS ou au travers de multiples études de l'IRSN. En plus de ces études expérimentales, le banc d'essai développé à l'INRS a fait l'objet d'une simulation numérique permettant de valider un modèle eulérien de transport et de dépôt implémenté dans un code de CFD destiné à modéliser le comportement d'un nanoaérosol. Les résultats numériques/expérimentaux sont concordants ; les ordres de grandeur des niveaux de confinement atteints sont comparables / The thesis works have enabled us to quantify the containment efficiency of two devices (a microbiological safety cabinet and classical fume hood) during the simultaneous production of nanoaerosols and a tracer gas (SF6). Two different measurement techniques were used: the first based on the measurement of particle size distribution of the escaping aerosol (SMPS-C), the other based on the detection of fluorescence of samples (sodium fluorescein used as marker of nanoparticles). The results have established a strong correlation between the behavior of a nanoaerosols and the tracer gas when they are emitted simultaneously in a ventilated enclosure. More, we observed that tracer gas back diffusion was almost twice greater than for nanoparticles back diffusion in all the tested configurations. The deposit and the agglomeration present in the case of transport of a cloud of nanoparticles can explain these differences in the overall level of containment. However, this observation does not guarantee sufficient protection since there is no specific reference value for nanoparticle exposure. It is useful to observe the guidelines that have been defined in many INRS publications or through IRSN studies. In addition to these experimental studies, the test-rig developed at INRS has been numerically simulated to validate an eulerian transport and deposition model implemented in a CFD code for modeling the behavior of a nanoaerosol. Numerical and experimental results are concordant; orders of magnitude for the achieved containment levels are comparable
|
4 |
Microstructural Analysis of Linear Friction Welded Joint in Nickel-Base Inconel 738 SuperalloyOla, Oyedele Temitope 19 January 2011 (has links)
Inconel 738 (IN 738), like other precipitation-hardened nickel-base superalloys that contain a substantial amount of Al and Ti, is very difficult to weld due to its high susceptibility to heat-affected zone (HAZ) cracking during conventional fusion welding processes. The cause of this cracking, which is usually intergranular in nature, has been attributed to the liquation of various phases in the alloy, subsequent wetting of the grain boundaries by the liquid and decohesion along one of the solid-liquid interfaces due to on-cooling tensile stresses. To address the problem of liquation cracking in weldments, recent developments in welding research have resulted in supposedly exclusive solid-state friction joining processes, such as linear friction welding (LFW), for joining crack susceptible structural alloys. The objective of this work was therefore to investigate the weldability of the difficult-to-weld IN 738 superalloy by LFW and to analyze the resulting microstructural changes in the alloy due to the welding process. LFW was performed on Linear Friction Welding Process Development System (PDS) at the Aerospace Manufacturing Technology Centre of the Institute for Aerospace Research, National Research Council (NRC) of Canada. In order to study and decouple the effect of non-equilibrium thermal cycle and imposed compressive stress during the joining, physical simulation of the LFW process was performed by using Gleeble 1500-D Thermo-Mechanical Simulation System at the University of Manitoba. Detailed microstructural study of welded and Gleeble-simulated materials was carried out. Correlation between the simulated microstructure and that of the weldments was obtained, in that, a significant grain boundary liquation was observed in both the simulated specimens and actual weldments due to non-equilibrium reaction of second phase particles, including the strengthening gamma prime phase. These results show that in contrast to the general assumption of LFW being an exclusively solid-state joining process, intergranular liquation, caused by non-equilibrium phase reaction(s), occurred during the process. However, despite a significant occurrence of liquation in the alloy, no HAZ cracking was observed. Nevertheless, the result showed that crack-free welding by linear friction welding is not due to preclusion of grain boundary liquation as has been commonly assumed and reported. Instead, resistance to cracking can be related to the counter-crack-formation effect of the imposed strain and to a concept observed and reported for the first time in this work, which is strain-induced rapid solidification. Furthermore, microstructural evolution during joining cannot be understood without considering the concept of non-equilibrium liquation reaction and strain-induced rapid solidification of the metastable liquid, which are carefully elucidated in this thesis.
|
5 |
Microstructural Analysis of Linear Friction Welded Joint in Nickel-Base Inconel 738 SuperalloyOla, Oyedele Temitope 19 January 2011 (has links)
Inconel 738 (IN 738), like other precipitation-hardened nickel-base superalloys that contain a substantial amount of Al and Ti, is very difficult to weld due to its high susceptibility to heat-affected zone (HAZ) cracking during conventional fusion welding processes. The cause of this cracking, which is usually intergranular in nature, has been attributed to the liquation of various phases in the alloy, subsequent wetting of the grain boundaries by the liquid and decohesion along one of the solid-liquid interfaces due to on-cooling tensile stresses. To address the problem of liquation cracking in weldments, recent developments in welding research have resulted in supposedly exclusive solid-state friction joining processes, such as linear friction welding (LFW), for joining crack susceptible structural alloys. The objective of this work was therefore to investigate the weldability of the difficult-to-weld IN 738 superalloy by LFW and to analyze the resulting microstructural changes in the alloy due to the welding process. LFW was performed on Linear Friction Welding Process Development System (PDS) at the Aerospace Manufacturing Technology Centre of the Institute for Aerospace Research, National Research Council (NRC) of Canada. In order to study and decouple the effect of non-equilibrium thermal cycle and imposed compressive stress during the joining, physical simulation of the LFW process was performed by using Gleeble 1500-D Thermo-Mechanical Simulation System at the University of Manitoba. Detailed microstructural study of welded and Gleeble-simulated materials was carried out. Correlation between the simulated microstructure and that of the weldments was obtained, in that, a significant grain boundary liquation was observed in both the simulated specimens and actual weldments due to non-equilibrium reaction of second phase particles, including the strengthening gamma prime phase. These results show that in contrast to the general assumption of LFW being an exclusively solid-state joining process, intergranular liquation, caused by non-equilibrium phase reaction(s), occurred during the process. However, despite a significant occurrence of liquation in the alloy, no HAZ cracking was observed. Nevertheless, the result showed that crack-free welding by linear friction welding is not due to preclusion of grain boundary liquation as has been commonly assumed and reported. Instead, resistance to cracking can be related to the counter-crack-formation effect of the imposed strain and to a concept observed and reported for the first time in this work, which is strain-induced rapid solidification. Furthermore, microstructural evolution during joining cannot be understood without considering the concept of non-equilibrium liquation reaction and strain-induced rapid solidification of the metastable liquid, which are carefully elucidated in this thesis.
|
Page generated in 0.0451 seconds