In this thesis, the problem of controlling a surgical masterand slave system with force reflection is studied. The problemof stiff contacts between the slave and the environment isgiven specific attention. The work has been carried out at KTHbased on an initial cooperation with Karolinska Sjukhuset. Theaim of the over all project is to study the possibilities forintroduction of a force reflective teleoperator in neurologicalskullbase operations for the particular task of bone millingand thereby, hopefully, increase patient safety, decreasesurgeon workload and cost forthe society. The main contributions of this thesis are: Derivation of a dynamical model of the master andoperator’s finger system and, experimental identificationof ranges on model parameter values. Based on this model, theinteraction channel controllers optimized for transparency arederived and modified to avoid the influence of the uncertainmodel parameters. This results in a three channel structure. Todecrease the influence of the uncertain parameters locally atthe master, a control loop is designed such that the frequencyresponse of the reflected force is relatively unaffected by theuncertainties, a result also confirmed in a transparencyanalysis based on the H-matrix. The developed teleoperatorcontrol structure is tested in experiments where the operatorcould alter the contact force without facing any problems aslong as the slave is in contact with the environment. As a result of the severe difficulties for the teleoperatorto move from free space motion to in-contact manipulationwithout oscillative behaviour, a new detection algorithm basedon passivity theory is developed. The algorithm is able todetect the non-passive behaviour of the actual teleoperatorinduced by the discrete change in system dynamics occurring atthe contact instant. A stabilization controller to be activatedby the detection algorithm is designed and implemented on themaster side of the teleoperator. The detection algorithm andthe stabilization controller are shown highly effective in realexperiments. All major research results presented in the thesis have beenverified experimentally. KeywordsTeleoperator, Force Feedback, Passivity, StiffContacts, Control, Robustness, Transparency, Bone Milling,Uncertainty

<p>In this thesis, the problem of controlling a surgical masterand slave system with force reflection is studied. The problemof stiff contacts between the slave and the environment isgiven specific attention. The work has been carried out at KTHbased on an initial cooperation with Karolinska Sjukhuset. Theaim of the over all project is to study the possibilities forintroduction of a force reflective teleoperator in neurologicalskullbase operations for the particular task of bone millingand thereby, hopefully, increase patient safety, decreasesurgeon workload and cost forthe society.</p><p>The main contributions of this thesis are:</p><p>Derivation of a dynamical model of the master andoperator’s finger system and, experimental identificationof ranges on model parameter values. Based on this model, theinteraction channel controllers optimized for transparency arederived and modified to avoid the influence of the uncertainmodel parameters. This results in a three channel structure. Todecrease the influence of the uncertain parameters locally atthe master, a control loop is designed such that the frequencyresponse of the reflected force is relatively unaffected by theuncertainties, a result also confirmed in a transparencyanalysis based on the H-matrix. The developed teleoperatorcontrol structure is tested in experiments where the operatorcould alter the contact force without facing any problems aslong as the slave is in contact with the environment.</p><p>As a result of the severe difficulties for the teleoperatorto move from free space motion to in-contact manipulationwithout oscillative behaviour, a new detection algorithm basedon passivity theory is developed. The algorithm is able todetect the non-passive behaviour of the actual teleoperatorinduced by the discrete change in system dynamics occurring atthe contact instant. A stabilization controller to be activatedby the detection algorithm is designed and implemented on themaster side of the teleoperator. The detection algorithm andthe stabilization controller are shown highly effective in realexperiments.</p><p>All major research results presented in the thesis have beenverified experimentally.</p><p><b>Keywords</b>Teleoperator, Force Feedback, Passivity, StiffContacts, Control, Robustness, Transparency, Bone Milling,Uncertainty</p>

The research presented in this thesis describes a substantial part of the design of a prototypical surgical training simulator. The results are intended to be applied in future simulators used to educate and train surgeons for bone milling operations. In earlier work we have developed a haptic bone milling surgery simulator prototype based on three degrees-of-freedom force feedback. The contributions presented here constitute an extension to that work by further developing the haptic algorithms to enable six degrees-of-freedom (6-DOF) haptic feedback. Such feedback is crucial for a realistic haptic experience when interacting in a more complex virtual environment, particularly in milling applications.The main contributions of this thesis are:The developed 6-DOF haptic algorithm is based on the work done by Barbic and James, but differs in that the algorithm is modified and optimized for milling applications. The new algorithm handles the challenging problem of real-time rendering of volume data changes due to material removal, while fulfilling the requirements on stability and smoothness of the kind of haptic applications that we approach. The material removal algorithm and the graphic rendering presented here are based on the earlier research. The new 6-DOF haptic milling algorithm is characterized by voxel-based collision detection, penalty-based and constraint-based haptic feedback, and by using a virtual coupling for stable interaction.Milling a hole in an object in the virtual environment or dragging the virtual tool along the surface of a virtual object shall generate realistic contact force and torque in the correct directions. These are important requirements for a bone milling simulator to be used as a future training tool in the curriculum of surgeons. The goal of this thesis is to present and state the quality of a newly developed 6-DOF haptic milling algorithm. The quality of the algorithm is confirmed through a verification test and a face validity study performed in collaboration with the Division of Orthopedics at the Karolinska University Hospital. In a simulator prototype, the haptic algorithm is implemented together with a new 6-DOF haptic device based on parallel kinematics. This device is developed with workspace, transparency and stiffness characteristics specifically adapted to the particular procedure. This thesis is focuses on the 6-DOF haptic algorithm. / QC 20120226