No description available.

<p>No comments. Thanks.</p> / <p>Advanced electrodes based on MnO₂ for the electrochemical supercapacitor (ES) application have been fabricated using electrochemical and chemical methods.</p> <p>Electrosynthesis method has been utilized for the in-situ impregnation of manganese dioxide in commercial Ni plaque current collectors. Dipping-reduction, cathodic galvanostatic and reverse pulse electrosynthesis methods were investigated. The material loading was varied by the variation of the number of the dipping-reduction procedures in the chemical precipitation method or by the variation of charge passed in the electrochemical methods. The results obtained by different methods were compared. The dipping-reduction method offered the advantage of higher specific capacitances (SCs) at high scan rates, whereas other methods allowed higher material synthesis rate.</p> <p>Cathodic electrolytic deposition (ELD) has been utilized for the fabrication of Ag-doped MnO₂ films. The Ag-doped MnO₂ films showed improved capacitive behavior and lower electrical resistance of 0.6 Ohm compared to pure MnO₂ films. The highest SC of 770 F g^-1 was obtained at a scan rate of 2 mV s^-1 in the 0.5 M Na₂SO₄ electrolyte.</p> <p>Electrodes for ES application were fabricated by cathodic electrodeposition of MnO₂ on CNTs, which were grown by chemical vapor deposition on stainless steel meshes. The MnO₂-CNT nanocomposites showed excellent capacitive behavior and low electrical resistance of 0.5 Ohm.</p> <p>Electrophoretic deposition (EPD) has been utilized for the deposition of composite MnO₂-multiwalled carbon nanotube (MWCNT) films for the ES application. Dopamine (DA), caffeic acid (CA), tyramine (TA), gallic acid (GA), polyacrylic acid (PAA) and pyrocatechol violet (PV) were shown to be effective and universal charging additives, which provide stabilization of MnO₂ nanoparticles and MWCNTs in the suspensions. The influence of the structure of the organic molecules on their adsorption on the oxide nanoparticles has been investigated. We discovered that the number and site of OH group for dispersants were essential for the adsorption on oxide materials, and the number of aromatic ring was important for the adsorption on carbon materials. Pure CNT films were deposited using PV as a dispersant, which was the first time in literature to prepare pure CNT film using a dispersant. SCs decrease with increasing film thickness. SCs of composite MnO₂-MWCNT obtained using EPD were in the range of 350-650 F g^-1 depending on material loadings.</p> / Doctor of Science (PhD)

<p>Single-walled carbon nanotubes (SWNTs) are of special interest in current research due to their extraordinary mechanical, electronic and optical properties. Their unique structure, remarkable thermal and electrical conductivity, and high mechanical strength make SWNTs viable candidates for a wide range of device applications. However, pristine CNTs are not dispersible in most solvents, the main difficulties in CNT applications are related to their purification and solution-phase processing. In recent years, the supramolecular functionalization of SWNTs with conjugated polymers has received significant attention. Research within this field has been driven by the desire to find polymer structures that can selectively disperse certain nanotubes species with high efficiency.</p> <p>After a brief overview of the studies that are related to the investigation of the supramolecular interaction between various conjugated polymers and SWNTs (chapter 1), the synthesis of fluorene and thiophene-based conjugated polymers and their supramolecular complex formation properties with SWNTs are described (chapter 2, 3, 4, 5 and 6). In order to understand the effect that conjugated polymer structure has on formation of supramolecular complexes with SWNTs, various factors were investigated by: (1) altering the polymer backbone composition; (2) varying the polymer molecular weight; (3) introducing different solubilizing groups while the polymer backbone remained the same; (4) changing the polymer conformation. All of the resulting polymer-nanotube assemblies exhibit excellent solution stability in THF in the absence of excess unbound free polymer. The spectroscopic characterization of the polymer-SWNT complex materials indicated that the interaction between the conjugated polymers and SWNTs is strongly influenced by polymer structure.</p> <p>The interaction between a water soluble polythiophene derivative, poly[3-(3-N,N-diethylaminopropoxy)-thiophene] (PDAOT), and SWNTs is discussed in chapter 7. It is also demonstrated that the PDAOT-SWNT complexes form stable aqueous solutions that can be used for the fabrication of highly sensitive amperometric glucose biosensors.</p> / Doctor of Philosophy (PhD)

<p>In this thesis, a modern transmission electron microscope is used to perform high-resolution electron energy loss studies of metallic nanostructures and carbon nanotubes.</p> <p>The remarkable optical properties of metallic nanostructures arise from the excita- tion of surface plasmons. With improved instrumentation, surface plasmon resonances are imaged in a variety of nanostructures, enabling a greater understanding of their behaviour in nanoscale systems. It is shown that surface plasmons set up multiple high order resonances in silver nanorods, and they freely propagate around sharp corners in silver nanowires. It is also demonstrated that silver nanorice structures resonate in a similar manner to nanorods, despite the high density of stacking faults in the structure. Finally, a complementary structural pair is found to resonate in a complementary fashion, in agreement with Babinet’s principle.</p> <p>Carbon nanotubes exhibit unique physicochemical properties that have led to their use in a variety of novel materials science applications. Despite rapid progress in the theoretical and experimental investigation of carbon nanotubes, techniques capable of studying the structural and electronic properties of individual tubes are limited. Here, it is demonstrated that the spectral signature of carbon can be used to identify the electronic character of individual single-walled carbon nanotubes. In addition, a new technique is used to map bonding anisotropy in a multi-walled carbon nanotube.</p> <p>Also presented in this thesis is the design and construction of a unique laser-TEM system. Early results from the system include in-situ measurements of laser-induced structural and electronic distortions in individual carbon nanotubes.</p> / Doctor of Philosophy (PhD)

Disinfectants are added to the water distribution system and swimming pools to control the growth of pathogenic microorganisms in water. High disinfectant levels are health hazards since they produce disinfectant by-products which are carcinogens. Thus, monitoring the amount ofresidual disinfectants present and maintaining an optimal amount of residual disinfectants throughout the distribution network is very crucial for safe water distribution. Colorimetric measurements are the current standard for measuring disinfectant levels in water. However, it is very difficult to integrate colorimetric measurements into automated monitoring devices. Redox active molecules like the phenyl-capped aniline tetramer (PCAT) can be incorporated as a dopant into a single wall carbon nanotube sensor for detecting oxidant in drinking water. The sensor works on the principle of oxidizing adsorbed redox molecules on carbon nanotubes by oxidant present in drinking water thus changing the resistivity of the carbon nanotube film. Most commonly used disinfectants are HOCl, Cl2, ClO2, Chloramine, KMnO4, HOBr, H2O2, O3, Br2, I2, etc. They all are oxidizing agents and can be distinguished from one another as they have different oxidation potentials. For water treatment purposes, it is not enough to know the disinfectant level, but it is also very important to identify which disinfectant is present. Currently, there is no standard method for distinguishing different disinfectants presents in water. The development of sensor arrays based on redox active molecules having different redox potentials is a potential pathway towards differentiating between different disinfectants in water. Different aniline oligomers were synthesized to create a library of redox active molecules. Redox properties of these molecules have been determined, and expected results were compared with the sensor performance. In the future, these sensors can be incorporated into a reliable, resettable and reagent free sensor array for monitoring and distinguishing different disinfectants in water. Being able to constantly monitor the disinfectant level and identifying the disinfectant present in water will enable us to design an improved and sustainable disinfecting system. / Thesis / Master of Science (MSc)

The vast majority of commercial gas separation membrane systems are polymeric because of processing feasibility and cost. However, polymeric membranes designed for gas separations have been known to have a trade-off between permeability and selectivity as shown in Robeson's upper bound curves. The search for membrane materials that transcend Robeson's upper bound has been the critical issue in research focused on membranes for gas separation in the past decade. To that end, many researchers have explored the idea of mixed matrix membranes (MMMs). These membranes combine a polymer matrix with inorganic molecular sieves such as zeolites. The ideal filler material in MMMs should have excellent properties as a gas adsorbent or a molecular sieve, good dispersion properties in the polymer matrix of submicron thickness, and should form high quality interfaces with the polymer matrix. In order to increase gas permeance and selectivity of polymeric membranes by fabricating MMMs, we have fabricated mixed matrix membranes using carbon nanotubes (CNTs) and nano-sized mesoporous silica. Mixed matrix membranes containing randomly oriented CNTs showed that addition of nanotubes to a polymer matrix could improve its selectivity properties as well as permeability by increasing diffusivity. Overall increases in permeance and diffusivity for all tested gases suggested that carbon nanotubes can provide high diffusivity tunnels in the CNT within the polymer matrix. This result agreed well with molecular simulation estimations. In order to prepare ordered CNTs membranes, we have developed a simple, fast, commercially attractive, and scalable orientation method. The oriented CNT membrane sample showed higher permeability by one order of magnitude than the value predicted by a Knudsen model. This CNT membrane showed higher selectivities for CO₂ over other gas molecules because of preferential interaction of CO₂ with the amine functionalized nanotubes, demonstrating practical applications in gas separations. Recently, mesoporous molecular sieves have been used in MMMs to enhance permeability or selectivity. However, due to their micrometer scale in particle size, the composite membrane was extremely brittle and tended to crack at higher silica loading. In this study, we have developed fabrication techniques to prepare MMMs containing mesoporous MCM-41 nanoparticles on the order of ~50 nm in size. This smaller nanoparticle lead to higher polymer/particle interfacial area and provides opportunity to synthesize higher loading of molecular sieves in polymer matrix up to ~80 vol%. At 80 vol% of nano-sized MCM-41 silica loading, the permeability of the membrane increased dramatically by 300 %. Despite these increases in permeability, the separation factor of the MMMs changed only slightly. Therefore, these nanoscale molecular sieves are more suitable for commercialization of MMMs with very thin selective layers than are micro-sized zeolites or molecular sieves. / Ph. D.

Polymeric membranes for gas separation are limited in their performance by a trade-off between permeability and selectivity. New methods of design are necessary in making membranes, which can show both high permeability and selectivity. A mixed matrix membrane is one such particular design, which brings in the superior gas separation performance of inorganic membranes together with the easy processability and price of the polymers. In a mixed matrix membrane, the inorganic phase is dispersed in the polymeric continuous phase. Nanocomposite membranes have a more sophisticated design with a thin separation layer on top of a porous support. The objective of this research was to fabricate thin SWNT nanocomposite membranes for gas separation, which have both high permeability and selectivity. SWNT/polyacrylic nanocomposite membranes were fabricated by orienting the SWNTs by high vacuum filtration. The orientation of SWNTs on top of the porous support was sealed by UV polymerization. For making these membranes, the CNTs were purified and cut into small open tubes simultaneously functionalizing them with COOH groups. Gas sorption of CO2 in COOH functionalized SWNTs was lower than in purified SWNTs. Permeabilities in etched membrane were higher than Knudsen permeabilities by a factor of 8, and selectivities were similar to Knudsen selectivities. In order to increase the selectivities, SWNTs were functionalized with zwitterionic functional groups. Gas sorption in zwitterion functionalized SWNTs was very low compared to in COOH functionalized SWNTs. This result showed that the zwitterionic functional groups are kinetically blocking the gas molecules from entering the pore of the CNT. SWNT/polyamide nanocomposite membranes were fabricated using the zwitterion functionalized SWNTs by interfacial polymerization. The thickness of the separation layer was around 500nm. Gas permeabilities in the CNT membranes increased with increasing weight percentage of the SWNTs. Gas permeabilities were higher in COOH SWNT membrane than in zwitterion SWNT membrane. Gas selectivities were similar to the Knudsen selectivities, and also to the intrinsic selectivities in the pure polyamide membrane. The water flux in SWNT-polyamide membranes increased with increasing weight percentage of zwitterion functionalized SWNTs, along with a slight increase in the salt rejection. Membranes exhibited less than 1% variability in its performance over three days. / Ph. D.

Carbon nanomaterials have attracted significant attention in the past decades for their unique properties and potential applications in many areas. This dissertation addresses the preparation, functionalization and potential biomedical applications of various carbonaceous nanomaterials. Trimetallic nitride template endohedral metallofullerenes (TNT-EMFs, M₃N@C₈₀, M = Gd, Lu, etc.) are some of the most promising materials for biomedical applications. Water-soluble Gd₃N@C₈₀ was prepared by the functionalization with poly(ethylene glycol) (PEG) and hydroxyl groups (Gd₃N@C₈₀[DiPEG(OH)ₓ]). The length of the PEG chain was tuned by changing the molecular weight of the PEG from 350 to 5000. The 1H magnetic resonance relaxivities of the materials were studied at 0.35 T, 2.4 T and 9.4 T. Their relaxivities were found to increase as the molecular weight of the PEG decreased, which is attributed to the increasing aggregate size. The aggregate sizes were confirmed by dynamic light scattering. In vivo study suggested that Gd3N@C₈₀[DiPEG(OH)x] was a good candidate for magnetic resonance imaging (MRI) contrast agents. Another facile method was also developed to functinalize Gd₃N@C₈₀ with both carboxyl and hydroxyl groups by reaction with succinic acyl peroxide and sodium hydroxide thereafter. The product was determined to be Gd₃N@C₈₀(OH)~₂₆(CH₂CH₂COOM)~₁₆ (M = Na, H) by X-ray photoelectron spectrometry. The Gd₃N@C₈₀(OH)~₂₆(CH₂CH₂COOM)~₁₆ also exhibited high relaxivity, and aggregates in water. The research on both pegylated and carboxylated Gd₃N@C₈₀ suggests that aggregation and rotational correlation time plays an important role in relaxation, and the relaxivities and aggregation of the water-soluble metallofullerenes can be tuned by varying the molecular weight of the functionality. TNT-EMFs can be encapsulated inside single-walled carbon nanotubes (SWNTs) to form "peapod" structures by heating the mixture of TNT-EMFs and SWNTs in a vacuum. The peapods were characterized by Raman spectrometry and transmission electron microscopy (TEM). The peapods were then functionalized with hydroxyl groups by a high speed vibration milling (HSVM) method in the presence of KOH. The functionalized Gd-doped peapods exhibited high relaxivites and had an additional advantage of "double carbon wall" protection of the toxic Gd atoms from possible leaking. The HSVM method was modified by using succinic acyl peroxide. The modified HSVM method could functionalize multi-walled carbon nanotubes (MWNT) and single-walled carbon nanohorns (SWNHs) with carboxyl groups. In the presence of N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride (EDC), carboxylate MWNTs and SWNHs could be conjugated with CdSe/ZnS quantum dots (QDs). TNT-EMFs were also encapsulated inside SWNHs to form SWNH peapods. SWNH peapods were functionalized by the modified HSVM method and then were conjugated with CdSe/ZnS QDs. The peapods were characterized by TEM. In vitro and in vivo studies indicated that SWNH peapods could serve as a multimodal diagnostic agent: MRI contrast agent (Gd₃N@C₈₀ encapsulated), radio-active therapeutic agent (Lu₃N@C₈₀ encapsulated) and optical imaging agent (QDs). / Ph. D.

The dispersion quality of nanoinclusions within a matrix material is often overlooked when relating the effect of nanoscale structures on functional performance and processing/property relationships for nanocomposite materials. This is due in part to the difficulty in visualizing the nanoinclusion and ambiguity in the description of dispersion. Understanding the relationships between the composition of the nanofiller, matrix chemistry, processing procedures and resulting dispersion is a necessary step to tailor the physical properties. A method is presented that incorporates high-contrast imaging, an emerging scanning electron microscopy technique to visualize conductive nanofillers deep within insulating materials, with various image processing procedures to allow for the quantification and validation of dispersion parameters. This method makes it possible to quantify the dispersion of various single wall carbon nanotube (SWCNT)-polymer composites as a function of processing conditions, composition of SWCNT and polymer matrix chemistry. Furthermore, the methodology is utilized to show that SWCNT dispersion exhibits fractal-like behavior thus allowing for simplified quantitative dispersion analysis. The dispersion analysis methodology will be corroborated through comparison to results from small angle neutron scattering dispersion analysis. Additionally, the material property improvement of SWCNT nanocomposites are linked to the dispersion state of the nanostructure allowing for correlation between dispersion techniques, quantified dispersion of SWCNT at the microscopic scale and the material properties measured at the macroscopic scale. / Ph. D.

Poly(lactic acid) is biodegradable polymer derived from renewable resources and non-toxic, which has become most interested polymer to substitute petroleum-based polymer. However, it has low glass transition temperature and poor gas barrier properties to restrict the application on hot contents packaging and long-term food packaging. The objectives of this research are: (a) to reduce coagulation of graphene oxide/single-walled carbon nanotube (GOCNT) nanocomposite in poly(lactic acid) matrix and (b) to improve mechanical strength and oxygen barrier property, which extend the application of poly(lactic acid). Graphene oxide has been found to have relatively even dispersion in poly(lactic acid) matrix while its own coagulation has become significant draw back for properties of nanocomposite such as gas barrier, mechanical properties and thermo stability as well as crystallinity. Here, single-walled carbon nanotube was hybrid with graphene oxide to reduce irreversible coagulation by preventing van der Waals of graphene oxide. Mass ratio of graphene oxide and carbon nanotube was determined as 3:1 at presenting greatest performance of preventing coagulation. Four different weight percentage of GOCNT nanocomposite, which are 0.05, 0.2, 0.3 and 0.4 weight percent, were composited with poly(lactic acid) by solution blending method. FESEM morphology determined minor coagulation of GOCNT nanocomopsite for different weight percentage composites. Insignificant crystallinity change was observed in DSC and XRD data. At 0.4 weight percent, it prevented most of UV-B light but was least transparent. GOCNT nanocomposite weight percent was linearly related to ultimate tensile strength of nanocomposite film. The greatest ultimate tensile strength was found at 0.4 weight percent which is 175% stronger than neat poly(lactic acid) film. Oxygen barrier property was improved as GOCNT weight percent increased. 66.57% of oxygen transmission rate was reduced at 0.4 weight percent compared to neat poly(lactic acid). The enhanced oxygen barrier property was ascribed to the outstanding impermeability of hybrid structure GOCNT as well as the strong interfacial adhesion of GOCNT and poly(lactic acid) rather than change of crystallinity. Such a small amount of GOCNT nanocomposite improved mechanical strength and oxygen barrier property while there were no significant change of crystallinity and thermal behavior found. / Master of Science