There are different methods used in the surgical treatment of peripheral nerve injury. In this respect, end-to-end surgical reconnection of the damaged nerve ends or autologous nerve grafts are applied as soon as possible after the injury. When autologous tissue transplant is considered, there are some medical devices available generally for relatively short nerve defects. As a solution for this problem, different tissue engineered nerve conduits have been developed. In the current study, a pHEMA hydrogel membranes were designed to mimic the tubular conduits and they were loaded with 1-6% (w/w) multiwalled carbon nanotubes (mwCNTs) to obtain electrical conductivity. The most important reason for the use of CNTs in peripheral nerve injury is their electrical conductivity. Within the context of the study, the degree of swelling, contact angles, electrical conductivity and mechanical properties of the membranes were analyzed. As the amount of mwCNTs were increased, the contact angles, indicating higher hydrophobicity and the electrical conductivity increased. The tensile test of the mwCNT-pHEMA composite membranes showed that the membranes have viscoelastic structure similar to the structure of the soft tissues. The structure of the mwCNT containing pHEMA composite membranes were analyzed with different microscopical techniques such as SEM, CSLM and microCT. MwCNTs on the hydrogels were morphologically similar to the original. SEM micrographs also showed that the mwCNTs were grouped in clumps on hydrogel surfaces. No mwCNT leaching was observed because the mwCNTs were embedded in the hydrogel, therefore, no cytotoxic effect was observed. The pHEMA hydrogels were porous which is suitable for transportation of materials, electrolytes and gas needed for cell nutrition and growth. In the in vitro studies, SHSY5Y neuroblastoma cells were seeded on the membranes to determine the sustainability and effects of the membranes on the cell growth. Electrical potential of 1 and 2 V were used to stimulate the cells. Microscopical examination with SEM and CSLM, and MTT viability assay were used. The SHSY5Y neuroblastoma cells were attached and proliferated on both the composite and the hydrogel membranes. The cells on pHEMA membranes without mwCNTs, however, were not able to survive after application of electrical potential. As a conclusion, use of composite membranes in the treatment of peripheral nerve injury as a nerve conduit is appropriate. Electrical stimulation, however, did not induce the cells to align in contrast to the expected results, indicating potential and current application regime needs to be optimized to obtain the desired results.

This PhD dissertation presents the exploration and development of two carbon materials, carbon nanotubes (CNTs) and carbon fiber (CF), as either key functional components or unconventional substrates for a variety of MEMS applications. Their performances in three different types of MEMS devices, namely, strain/stress sensors, vibration-powered generators and fiber solar cells, were evaluated and the working mechanisms of these two non-traditional materials in these systems were discussed. The work may potentially enable the development of new types of carbon-MEMS devices. Firstly, a MEMS-assisted electrophoretic deposition (EPD) technique was developed, aiming to achieve controlled integration of CNT into both conventional and flexible MEMS systems. Selective deposition of electrically charged CNTs onto desired locations was realized in the EPD process through patterning of electric field lines created by the microelectrodes fabricated using MEMS techniques. A variety of 2-D and 3-D micropatterns of CNTs with controllable thickness and morphology have been successfully achieved in both rigid and elastic systems at room temperature with relatively high throughput. Studies also showed that high surface hydrophobicity of the non-conductive regions in microstructures was critical to accomplish well-defined selective micropatterning of CNTs through this strategy. A patterned PDMS/CNT nanocomposite was then fabricated through the aforementioned approach, and was incorporated, investigated and validated in elastic force/strain microsensors. The gauge factor of the sensor exhibited a strong dependence on both the initial resistance of the device and the applied strain. Detailed analysis of the data suggests that the piezoresistive effect of this specially constructed bi-layer composite could be three folds, and the sensing mechanism may vary when physical properties of the CNT network embedded in the polymer matrix alter. The feasibility of the PDSM/CNT nanocomposite serving as an elastic electret was further explored. The nanocomposite composed of these two non-traditional electret materials exhibited electret characteristics with reasonable charge storage stability. The power generation capacity of the corona-charged nanocomposite has been characterized and successfully demonstrated in both a ball drop experiment and the cyclic mechanical load experiments. Lastly, in an effort to develop carbon-material-based substrates for MEMS applications, a carbon fiber-based poly-Si solar cell was designed, fabricated and investigated. This fiber-type photovoltaics (PV) takes advantage of the excellent thermal stability, electrical conductivity and spatial format of the CF, which allows CF to serve as both the building block and the electrode in the PV configuration. The photovoltaic effects of the fiber PV were demonstrated with an open-circuit voltage of 0.14 V, a short-circuit current density of 1.7 mA/cm2, and output power density of 0.059mW/cm2. The issues of this system were discussed as well.

Carbon nanotubes show a wide range of transport behavior that varies from ballistic to hopping regime, depending on the nature of disorder in the system. Minute variations in disorder can lead from weak to strong localization, and this yields complex and intriguing features in the analysis of transport data. This dissertation reports an experimental study of charge transport in optically transparent single-wall carbon nanotube (SWNT) networks and field-effect devices. The SWNT network comprises randomly aligned (bundles of) tubes that have both high optical transparency in visible, near-infrared (IR) wavelength range and high electrical conductivity. Various aspects of charge transport in this material including magnetotransport, high electric-field transport and gate induced field-effect are investigated and presented within a consistent framework. The temperature dependence of resistance suggests hopping transport in the network. Since strong localization is observed for the disordered network, the disorder is further characterized by a magnetotransport study and a pulsed electric-field dependence study down to low temperatures (1.3 K). The magnetoresistance (MR) has contributions from two quantum effects -a forward interference mechanism leading to a negative MR and a wavefunction shrinkage mechanism leading to positive MR. The temperature dependence of the coefficient of this negative MR is shown to follow inverse power-law dependence, in accordance with theoretical predictions. The intrinsic parameters obtained from this analysis suggest a transverse localization of charge on the bundle boundaries. The electric-field dependence, measured to high fields, follows the predictions of hopping transport in high electric-field regime. A scaling analysis indicates that electric-field and temperature play similar roles in the transport. The calculated dependence of ‘threshold electric-field’ is also suggestive of this competing process between phonons and electric-field. The applicability of the concept of ‘effective temperature’ is explored for this system; the electric-field induced suppression of MR is studied. The network resistance as well as the optical transparency of the network is modulated with gate voltage using an electrolyte gate dielectric. The gating can tune the absorptions associated with the van Hove singularities in the SWNT DOS and a time response study for this ‘smart window’ is done for the modulation. A novel technique is used to characterize organic and nanotube field-effect transistors and this allows estimation of device parameters such as transconductance and channel impedance. The ac impedance of the SWNT network is also investigated as a possible tool to probe network connectivity. To summarize, the role of disorder in charge transport is investigated for these novel transparent SWNT networks using magnetic-field, electric-field, temperature and field-effect dependent transport measurements.

In the current context of rapidly depleting petroleum resources and growing environmental concerns, it is important to develop materials to harvest and store energy from renewable and sustainable sources. Hydrogen has the potential to be an alternative energy source, since it has higher energy content than petroleum. However, since hydrogen has very low volumetric energy density, hence it is important to design nano porous materials which can efficiently store large volumes of hydrogen gas by adsorption. In this regard carbon nanotube and Metal Organic Framework (MOFs) based materials are worth studying. Ionic liquids (IL) are potential electrolytes that can improve energy storage capacity and safety in Li ion batteries. Therefore it is important to understand IL's thermodynamic and transport properties, especially when it is in contact with electrode surface and mixed with Li salt, as happens in the battery application. This dissertation presents computation and simulation based studies on: 1. Hydrogen storage in carbon nanotube scaffold. 2. Mechanical property and stability of various nanoporous Metal Organic Frameworks. 3. Thermodynamic and transport properties of [BMIM][BF4] ionic liquid in bulk, in Li Salt mixture, on graphite surface and under nanoconfinement. In the first study, we report the effects of carbon nanotube diameter, tube chirality, tube spacer distance, tube functionalization and presence of Li on hydrogen sorption capacity and thermodynamics at different temperature and pressure. In the second one, we observe high pressure induced structural transformation of 6 isoreticular MOFs: IRMOF-1. IRMOF-3, IRMOF-6, IRMOF-8, IRMOF-10 and IRMOF-14, explore the deformation mechanism and effect of Hydrogen inside crystal lattice. In the third study, we observe the equilibrium thermodynamic and transport properties of [BMIM][BF4] ionic liquid. The temperature dependence of ion diffusion, conductivity, dielectric constant, dipole relaxation time and viscosity have been observed and found similar behavior to those of supercooled liquid. The ion diffusion on graphite surfaces and under nanoconfinement was found to be higher compared to those in bulk.

Radio frequency identification (RFID) and sensing are two key technologies enabling the Internet of Things (IoT). Development of RFID tags augmented with sensing capabilities (RFID sensor tags) would allow a variety of new applications, leading to a new paradigm of the IoT. Chipless RFID sensor technology offers a low-cost solution by eliminating the need of an integrated circuit (IC) chip, and is hence highly desired for many applications. On the other hand, printing technologies have revolutionized the world of electronics, enabling cost-effective manufacturing of large-area and flexible electronics. By means of printing technologies, chipless RFID sensor tags could be made flexible and lightweight at a very low cost, lending themselves to the realization of ubiquitous intelligence in the IoT era. This thesis investigated three construction methods of printable chipless RFID humidity sensor tags, with focus on the incorporation of the sensing function. In the first method, wireless sensing based on backscatter modulation was separately realized by loading an antenna with a humidity-sensing resistor. An RFID sensor tag could then be constructed by combining the wireless sensor with a chipless RFID tag. In the second method, a chipless RFID sensor tag was built up by introducing a delay line between the antenna and the resistor. Based on time-domain reflectometry (TDR), the tag encoded ID in the delay time between its structural-mode and antenna-mode scattering pulse, and performed the sensing function by modulating the amplitude of the antenna-mode pulse. In both of the above methods, a resistive-type humidity-sensing material was required. Multi-walled carbon nanotubes (MWCNTs) presented themselves as promising candidate due to their outstanding electrical, structural and mechanical properties. MWCNTs functionalized (f-MWCNTs) by acid treatment demonstrated high sensitivity and fast response to relative humidity (RH), owing to the presence of carboxylic acid groups. The f-MWCNTs also exhibited superior mechanical flexibility, as their resistance and sensitivity remained almost stable under either tensile or compressive stress. Moreover, an inkjet printing process was developed for the f-MWCNTs starting from ink formulation to device fabrication. By applying the f-MWCNTs, a flexible humidity sensor based on backscatter modulation was thereby presented. The operating frequency range of the sensor was significantly enhanced by adjusting the parasitic capacitance in the f-MWCNTs resistor. A fully-printed time-coded chipless RFID humidity sensor tag was also demonstrated. In addition, a multi-parameter sensor based on TDR was proposed.The sensor concept was verified by theoretical analysis and circuit simulation. In the third method, frequency-spectrum signature was utilized considering its advantages such as coding capacity, miniaturization, and immunity to noise. As signal collision problem is inherently challenging in chipless RFID sensor systems, short-range identification and sensing applications are believed to embody the core values of the chipless RFID sensor technology. Therefore a chipless RFID humidity sensor tag based on near-field inductive coupling was proposed. The tag was composed of two planar inductor-capacitor (LC) resonators, one for identification, and the other one for sensing. Moreover, paper was proposed to serve as humidity-sensing substrate for the sensor resonator on accounts of its porous and absorptive features. Both inkjet paper and ordinary packaging paper were studied. A commercial UV-coated packaging paper was proven to be a viable and more robust alternative to expensive inkjet paper as substrate for inkjet-printed metal conductors. The LC resonators printed on paper substrates showed excellent sensitivity and reasonable response time to humidity in terms of resonant frequency. Particularly, the resonator printed on the UV-coated packaging paper exhibited the largest sensitivity from 20% to 70% RH, demonstrating the possibilities of directly printing the sensor tag on traditional packages to realize intelligent packaging at an ultra-low cost. / <p>QC 20150326</p>

Shrinking volume, coupled with higher performance, microprocessors and integrated circuits have led to serious heat dissipation issues. In an effort to mitigate the excessive amounts of waste heat and ensure electronic survivability, heat sinks and spreaders are incorporated into heat generating device structures. This inevitability creates a thermal pathway through an interface. Thermal interfaces can possess serious thermal resistances for heat conduction. The introduction of a thermal interface material (TIM) can drastically increase the thermal performance of the component. Exceptional thermal properties of multiwall carbon nanotubes (MWCNTs) have spurred interest in their use as TIMs. MWCNTs inherently grow in vertically-oriented, high aspect ratio arrays, which is ideal in thermal interface applications because CNTs posses their superior thermal performance along their axis. In this paper, laser flash thermal characterization of sandwich‐bonded and cap‐screw‐bonded aluminum discs for both adhesive-infiltrated and “dry”, 100% MWCNT arrays, respectively. Thermal contact resistances as low as 18.1 mm2K/W were observed for adhesive‐infiltrated arrays and, even lower values, down to 10.583 mm2K/W were measured for “dry” MWCNT arrays. The improved thermal performance of the arrays compared to thermal adhesives and greases currently used in the electronics and aerospace industries, characterize MWCNT arrays as a novel, lighter‐weight, non‐corrosive replacement.

Vertically aligned Multiwalled Carbon Nanotubes (MWCNTs) were grown in the pores of Anodized Aluminum Oxide (AAO) templates and investigated for resistive sensor applications. High Sensitivity of 23% to low concentration (100 ppm) of ammonia was observed. An equivalent circuit model was developed to understand the current flow path in the resistive sensor. This helped us in achieving high sensitivities through amorphous carbon (a-C) layer thickness tailoring by employing post-growth processing techniques like plasma etching. A simulation model in MATLAB was developed to calculate the device resistance and the change in the sensitivity as a function of device parameters. The steady state response and transient response of the model to the number of ammonia molecules and its adsorption rate were studied. Effects of oxygen plasma, argon plasma and water plasma etch on thinning of the a-C layer were studied. In order to enhance the sensitivity, the top and bottom a-C layers were replaced by a more conductive metal layer. This also helped in understanding the current flow in the device and in the estimation of the resistivity of the a-C layer.

High performance/small package electronics create difficult thermal issues for integrated circuits. Challenges exist at material interfaces due to interfacial contact resistances. Multiwall carbon nanotube (MWCNT) arrays are considered to be excellent candidates for use as thermal interface materials (TIMs) due to outstanding thermal/mechanical properties. In this work, MWCNT array TIMs are analyzed in aluminum and carbon fiber composites via flash diffusivity analysis. The effect of TIM thickness, areal/bulk density, surface cleanliness, and volumetric packing fraction; along with the effect of substrate finish and interfacial contact pressure on thermal performance are analyzed. Trends show the best TIMs possess low thickness, high bulk density and packing fraction, and clean surfaces. Pressure dramatically increases thermal performance after establishing contact, with diminishing returns from additional pressure. Diffusivities approaching 40 mm2/s and 0.65 mm2/s are recorded for aluminum and composite systems. Oxygen plasma etching and high temperature annealing (“Graphitizing”) are investigated as methods to remove amorphous carbon from array surfaces. Graphitized TIMs report diffusivity improvements up to 53.8%. Three methods of incorporating MWCNTs into composites are attempted for thermal/mechanical property enhancement. Conductance calculations show increasing diffusivity without increasing thickness enhances thermal performance in composites. MWCNTs for mechanical property enhancement produce no change, or detrimental effects.

The current technological age is embodied by a constant push for increased performance and efficiency of electronic devices. This push is particularly observable for technologies that comprise free electron sources, which are used in various technologies including electronic displays, x-ray sources, telecommunication equipment, and spacecraft propulsion. Performance of these systems can be increased by reducing weight and power consumption, but is often limited by a bulky electron source with a high energy demand. Carbon nanotubes (CNTs) show favorable properties for field electron emission (FE) and performance as electron sources. This dissertation details the developments of a uniquely designed Spindt type CNT field emission array (CFEA), from initial concept to working prototype, to specifically prevent electrical shorting of the gate. The CFEA is patent pending in the United States. Process development enabled fabrication of a CFEA with a yield of up to 82%. Furthermore, a novel oxygen plasma etch process was developed to reverse shorting after CNT synthesis. CFEA testing demonstrates FE with a current density of up to 293 μA/cm² at the anode and 1.68 mA/cm² at the gate, with lifetimes in excess of 100 hours. A detailed analysis of eighty tested CFEAs revealed three distinct types of damage. Surprisingly, about half of the damaged chips are not electrically shorted, indicating that the CFEAs are very robust. Potential applications of this technology as cathodes for spacecraft electric propulsion were explored. Exposure to an operating electric propulsion thruster showed no significant effect or damage to the CFEAs, marking the first experimental study of CNT field emitters in an electric propulsion environment. A second effort in spacecraft propulsion is a collaboration with the Air Force Institute of Technology (AFIT). CFEAs are the payload on an AFIT developed Cube Satellite, called ALICE, to test electron emission in the space environment. ALICE has passed flight tests and is awaiting launch scheduled for 5 December 2013.

<p>The role of the surroundings, or <italic> environment </italic>, is essential in understanding funda- mental quantum-mechanical concepts, such as quantum measurement and quantum entanglement. It is thought that a dissipative environment may be responsible for certain types of quantum (i.e. zero-temperature) phase transitions. We observe such a quantum phase transition in a very basic system: a resonant level coupled to a dissipative environment. Specifically, the resonant level is formed by a quantized state in a carbon nanotube, and the dissipative environment is realized in resistive leads; and we study the shape of the resonant peak by measuring the nanotube electronic conductance.</p><p>In sequential tunneling regime, we find the height of the single-electron conductance peaks increases as the temperature is lowered, although it scales more weakly than the conventional T<super>-1</super>. Moreover, the observed scaling signals a close connec- tion between fluctuations that influence tunneling phenomenon and macroscopic models of the electromagnetic environment.</p><p>In the resonant tunneling regime (temperature smaller than the intrinsic level width), we characterize the resonant conductance peak, with the expectation that the width and height of the resonant peak, both dependent on the tunneling rate, will be suppressed. The observed behavior crucially depends on the ratio of the coupling between the resonant level and the two contacts. In asymmetric barriers the peak width approaches saturation, while the peak height starts to decrease.</p><p>Overall, the peak height shows a non-monotonic temperature dependence. In sym- metric barriers case, the peak width shrinks and we find a regime where the unitary conductance limit is reached in the incoherent resonant tunneling. We interpret this behavior as a manifestation of a quantum phase transition.</p><p>Finally, our setup emulates tunneling in a Luttinger liquid (LL), an interacting one-dimensional electron system, that is distinct from the conventional Fermi liquids formed by electrons in two and three dimensions. Some of the most spectacular properties of LL are revealed in the process of electron tunneling: as a function of the applied bias or temperature the tunneling current demonstrates a non-trivial power-law suppression. Our setup allows us to address many prediction of resonant tunneling in a LL, which have not been experimentally tested yet.</p> / Dissertation