No description available.

No description available.

No description available.

This thesis describes the development of a novel system, for metering of two-phase (gaswater) slug flows. The approach combines a model for stable slug flow, a non-intrusive set of conductance sensors, and appropriate closure relationships. This system allows each of the parameters in the model to be determined. The slug flow model is analysed, to determine the sensitivity of the phase flowrates to each measurement parameter. A metering system is then proposed which combines ring-shaped electrodes, electronic instrumentation, and processing software. The ring electrodes are optimised, for the measurement of the phase fraction and the translation velocity. New instrumentation is developed to activate the electrodes, with high measurement accuracy and a wide bandwidth. Analysis software is developed, to process the sensor data, provide suitable closure relations, and deliver the flowrates. A unique feature of this software is its ability to calculate uncertainty margins in the predicted flowrates. The NEL multiphase facility is used, to obtain data for developed, horizontal, gas-water slug flow in a 4-inch pipe. The data span the range of liquid phase superficial velocities 0.1 m s⁻¹ to 1.0 m s⁻¹, and gas phase superficial velocities 0.6 m s⁻¹ to 6.0 m s⁻¹. The analysis software is used to obtain the flowrate predictions and estimates for the uncertainty margins. The stable slug flow model does not give good results. The relative error in the gas phase prediction is between 10% and 100%, and for the liquid phase prediction, between 50% and 500%. The uncertainty margins are also of comparable magnitude. Proposals for improving the accuracy of the translation velocity measurement, and for directly measuring the local velocities in the slug body (using a pressure transducer) are presented. These proposals aim to reduce the uncertainty that is caused by the use of the empirical closure relationships in the model.

abstract: The sensor industry is a growing industry that has been predicted by Allied Market Research to be a multi-billion industry by 2022. One of the many key drives behind this rapid growth in the sensor industry is the increase incorporation of sensors into portable electrical devices. The value for sensor technologies are increased when the sensors are developed into innovative measuring system for application uses in the Aerospace, Defense, and Healthcare industries. While sensors are not new, their increased performance, size reduction, and decrease in cost has opened the door for innovative sensor combination for portable devices that could be worn or easily moved around. With this opportunity for further development of sensor use through concept engineering development, three concept projects for possible innovative portable devices was undertaken in this research. One project was the development of a pulse oximeter devise with fingerprint recognition. The second project was prototyping a portable Bluetooth strain gage monitoring system. The third project involved sensors being incorporated onto flexible printed circuit board (PCB) for improved comfort of wearable devices. All these systems were successfully tested in lab. / Dissertation/Thesis / Masters Thesis Engineering 2018

No description available.

Wearable sensors have garnered considerable interest because of their potential for various applications. However, much less has been studied about the Stretchsense pressure sensor characteristics and its workability for industrial application to prevent potential risk situations such as accidents and injuries. The proposed study helps investigate Stretchsense pressure sensors' applicability for measuring hand-handle interface forces under static and dynamic conditions. The BendLabs sensors - a multi-axis, soft, flexible sensing system was attached to the wrist to evaluate the wrist angle deviations. In addition, the StretchSense stretch sensors were attached to the elbow joint to help estimate the elbow flexion/extension. The research tests and evaluates the real-time pressure distribution across the hand while performing given tasks and investigates the relationship between the wrist and elbow position and grip strength. The research provides objective means to assess the magnitudes of high pressures that may cause pressure-induced discomfort and pain, thereby increasing the hand's stress. The experiment's most significant benefit lies in its applicability to the actual tool handles outside the laboratory settings.

Fluorescence spectroscopy has been considered to be one of the most important research techniques in modern analytical chemistry, biochemistry, and biophysics. At present, fluorescence is a dominant methodology widely used in a great number of research domains, including biotechnology, medical diagnostics, genetic analysis, DNA sequencing, flow cytometry, and forensic analysis, to name just a few. In the past decade, with the rapid development of fluorescence microscopy, there has been a considerable growth in applying fluorescence technique to cellular imaging. The distinguished merits of fluorescence techniques, such as high sensitivity, non-invasiveness, low cytotoxicity, low cost, and convenience, make it a promising tool to replace radioactive tracers for most biochemical measurements, avoiding the high expense and difficulties of handling radioactive tracers. Among the wide range of applications of fluorescence technique, fluorescent sensing of various cations and anions is one of the most important and active areas. This dissertation is all about developing fluorescent sensors for physiologically significant ions, including F-, K+, Fe3+, and Ca2+. All of these sensors demonstrate fluorescence "turn-on" response upon interacting with their respective ions, which makes them much more appealing than those based on fluorescence quenching mechanisms. In Chapter II, a novel highly selective fluorescence turn-on F- sensor (FS), comprised of a fluorene platform serving as the chromophore, and two 1,2,3-triazolium groups functioning as the signaling moieties, is described. The function of FS is established on the basis of deprotonation of the C-H bonds of 1,2,3-triazolium groups, which makes FS the first reported anion sensor based on the deprotonation of a C-H bond. Easy-to-prepare test strips were prepared for determining F- in aqueous media, providing an inexpensive and convenient approach to estimate whether the concentration of F- contained in drinking water is at a safe level. Chapter III contains an optimized synthesis of a reported K+-selective group (TAC), and the development of two TAC-based fluorescence turn-on K+ sensors (KS1 and KS2). The synthetic route of TAC is shortened and its overall yield is enhanced from 3.6% to 19.5%. Both KS1 and KS2 exhibited excellent selectivity toward K+ over other physiological metal cations, high sensitivity for K+ sensing, and pH insensitivity in the physiological pH range. Confocal fluorescence microscopy experiments demonstrate that they are capable of sensing K+ within living cells. 2PA determination reveals that KS2 has a desirable 2PA cross section of 500 GM at 940 nm, which makes it a two-photon red-emitting fluorescent sensor for K+. Chapter IV describes the development of a novel BODIPY-based fluorescence turn-on Fe3+ sensor (FeS). FeS is a conjugate of two moieties, a BODIPY platform serving as the fluorophore and a 1,10-diaza-18-crown-6 based cryptand acting as the Fe3+ recognition moiety. FeS displays good selectivity, high sensitivity, reversibility, and pH insensitivity toward Fe3+ sensing. Based on its excellent performance in determining Fe3+ and very low cytotoxicity, FeS was effectively applied to sensing Fe3+ in living cells. In Chapter V, a new BODIPY-based fluorescence turn-on sensor (CaS) was designed and synthesized for selectively and sensitively determining Ca2+. CaS is comprised of two moieties, a BODIPY fluorophore and a Ca2+ complexing unit. CaS demonstrated selective fluorescence turn-on response towards Ca2+ over other biological metal cations. Moreover, CaS exhibited desirable sensitivity for Ca2+ detection, which makes it more suitable for extracellular Ca2+ determination. In addition, CaS was insensitive to the pH of the physiological environment, especially in the pH range of blood and serum. Therefore, CaS has potential to be applied to sensing Ca2+ ions in extracellular environments. Chapter VI discusses potential future work of KS2 and CaS, following the results achieved in this dissertation. Based on the desirable performances of both sensors in sensing their respective ions, future work could largely be focused on their applications in cellular imaging.

No description available.

Today, sensing resources play a crucial role in the success of critical tasks such as border monitoring and surveillance. Although there are various types of resources available, each with different capabilities, only a subset of these resources are useful for a specific task. This is due to the dynamism in tasks' environment and the heterogeneity of the resources. Thus, an effective mechanism to select resources for tasks is needed so that the selected resources cater for the needs of the tasks. Though a considerable amount of research has already been done in different communities to efficiently allocate resources to tasks, we argue that there is little work done to guarantee the effectiveness of the section with respect to the context of operation. In this thesis, we propose a knowledge-based approach in which the context of operation is introduced to the resource selection process. First, we present a formalism to represent a sensor domain. We then introduce sound and complete mechanisms through which effective resource solutions for tasks are discovered. An extension to the representation is then proposed so that the agility in resource selection is increased. Finally, we present an architecture whereby a multitude of such knowledge bases are exposed as services so that a coalition can fully benefit from its networked resources; a query language – and its semantics – to discover appropriate service collections for user requirements are also presented. We have evaluated our work through controlled experiments and critical arguments. Through these evaluations, we have shown that our approach can indeed improve the resource selection process and can augment resource allocation mechanisms. Our approach is general in that, it can be applied in many other domains.