1 |
Aerodynamic Characteristics Of A Gas Turbine Exhaust Diffuser With An Accompanying Exhaust Collection SystemBernier, Bryan 01 January 2012 (has links)
The effects of an industrial gas turbine’s Exhaust Collector Box (ECB) geometry on static pressure recovery and total pressure loss were investigated in this study experimentally and computationally. This study aims to further understand how exit boundary conditions affect the performance of a diffuser system as well as the accuracy of industry standard computational models. A design of experiments approach was taken using a Box-Behnken design method for investigating three geometric parameters of the ECB. In this investigation, the exhaust diffuser remained constant through each test, with only the ECB being varied. A system performance analysis was conducted for each geometry using the total pressure loss and static pressure recovery from the diffuser inlet to the ECB exit. Velocity and total pressure profiles obtained with a hotwire anemometer and Kiel probe at the exit of the diffuser and at the exit of the ECB are also presented in this study. A total of 13 different ECB geometries are investigated at a Reynolds number of 60,000. Results obtained from these experimental tests are used to investigate the accuracy of a 3-dimensional RANS with realizable k-ε turbulence model from the commercial software package Star-CCM+. The study confirms the existence of strong counter-rotating helical vortices within the ECB which significantly affect the flow within the diffuser. Evidence of a strong recirculation zone within the ECB was found to force separation within the exhaust diffuser which imposed a circumferentially asymmetric pressure field at the inlet of the diffuser. Increasing the ECB width proved to decrease the magnitude of this effect, increasing the diffuser protrusion reduced this effect to a lesser degree. The combined effect of increasing the ECB Length and Width increased the expansion area ratio, proving to increase the system pressure recovery iv by as much as 19% over the nominal case. Additionally, the realizable k-ε turbulence model was able to accurately rank all 13 cases in order by performance; however the predicted magnitudes of the pressure recovery and total pressure loss were poor for the cases with strong vortices. For the large volume cases with weak vortices, the CFD was able to accurately represent the total pressure loss of the system within 5%.
|
2 |
Characterization Of An Inline Row Impingement Channel For Turbine Blade Cooling ApplicationsRicklick, Mark 01 January 2009 (has links)
Gas turbines have become an intricate part of today's society. Besides powering practically all 200,000+ passenger aircraft in use today, they are also a predominate form of power generation when coupled with a generator. The fact that they are highly efficient, and capable of large power to weight ratios, makes gas turbines an ideal solution for many power requirement issues faced today. Designers have even been able to develop small, micro-turbines capable of producing efficient portable power. Part of the turbine's success is the fact that their efficiency levels have continuously risen since their introduction in the early 1800's. Along with improvements in our understanding and designs of the aerodynamic components of the turbine, as well as improvements in the areas of material design and combustion control, advances in component cooling techniques have predominantly contributed to this success. This is the result of a simple thermodynamic concept; as the turbine inlet temperature is increased, the overall efficiency of the machine increases as well. Designers have exploited this fact to the extent that modern gas turbines produce rotor inlet temperatures beyond the melting point of the sophisticated materials used within them. This has only been possible through the use of sophisticated cooling techniques, particularly in the 1st stage vanes and blades. Some of the cooling techniques employed today have been internal cooling channels enhanced with various features, film and showerhead cooling, as well as internal impingement cooling scenarios. Impingement cooling has proven to be one of the most capable heat removal processes, and the combination of this cooling feature with that of channel flow, as is done in impingement channel cooling, creates a scenario that has understandably received a great deal of attention in recent years. This study has investigated several of the unpublished characteristics of these impingement channels, including the channel height effects on the performance of the channel side walls, effects of bulk temperature increase on heat transfer coefficients, circumferential heat variation effects, and effects on the uniformity of the heat transfer distribution. The main objectives of this dissertation are to explore the various previously unstudied characteristics of impingement channels, in order to sufficiently predict their performance in a wide range of applications. The potential exists, therefore, for a designer to develop a blade with cooling characteristics specifically tailored to the expected component thermal loads. Temperature sensitive paint (TSP) is one of several non-intrusive optical temperature measurements techniques that have gained a significant amount of popularity in the last decade. By employing the use of TSP, we have the ability to provide very accurate (less than 1 degree Celsius uncertainty), high resolution full-field temperature measurements. This has allowed us to investigate the local heat transfer characteristics of the various channel surfaces under a variety of steady state testing conditions. The comparison of thermal performance and uniformity for each impingement channel configuration then highlights the benefits and disadvantages of various configurations. Through these investigations, it has been shown that the channel side walls provide heat transfer coefficients comparable to those found on the target surface, especially at small impingement heights. Although the side walls suffer from highly non-uniform performance near the start of the channel, the profiles become very uniform as the cross flow develops and becomes a dominating contributor to the heat transfer coefficient. Increases in channel height result in increased non-uniformity in the streamwise direction and decreased heat transfer levels. Bulk temperature increases have also been shown to be an important consideration when investigating surfaces dominated by cross flow heat transfer effects, as enhancements up to 80% in some areas may be computed. Considerations of these bulk temperature changes also allow the determination of the point at which the flow transitions from an impingement dominated regime to one that is dominated by cross flow effects. Finally, circumferential heat variations have proven to have negligible effects on the calculated heat transfer coefficient, with the observed differences in heat transfer coefficient being contributed to the unaccounted variations in channel bulk temperature.
|
3 |
On The Nature Of The Flow In A Separated Annular DiffuserDunn, Jason 01 January 2009 (has links)
The combustor-diffuser system remains one of the most studied sections of the turbomachine. Most of these investigations are due to the fact that quite a bit of flow diffusion is required in this section as the high speed flow exits the compressor and must be slowed down to enter the combustor. Like any diffusion process there is the chance for the development of an unfavorable adverse pressure gradient that can lead to flow separation; a cause of drastic losses within a turbine. There are two diffusion processes in the combustor-diffuser system: The flow first exits the compressor into a pre-diffuser, or compressor discharge diffuser. This diffuser is responsible for a majority of the pressure recovery. The flow then exits the pre-diffuser by a sudden expansion into the dump diffuser. The dump diffuser comprises the majority of the losses, but is necessary to reduce the fluid velocity within acceptable limits for combustion. The topic of active flow control is gaining interest in the industry because such a technique may be able to alleviate some of the requirements of the dump diffuser. If a wider angle pre-diffuser with separation control were used the fluid velocity would be slowed more within that region without significant losses. Experiments were performed on two annular diffusers to characterize the flow separation to create a foundation for future active flow control techniques. Both diffusers had the same fully developed inlet flow condition, however, the expansion of the two diffusers differed such that one diffuser replicated a typical compressor discharge diffuser found in a real machine while the other would create a naturally separated flow along the outer wall. Both diffusers were tested at two Reynolds numbers, 5x104 and 1x105, with and without a vertical wall downstream of the exit to replicate the dump diffuser that re-directs the flow from the pre-diffuser outlet to the combustor. Static pressure measurements were obtained along the OD and ID wall of the diffusers to determine the recovered pressure throughout the diffuser. In addition to these measurements, tufts were used to visualize the flow. A turbulent CFD model was also created to compare against experimental results. In the end, the results were validated against empirical data as well as the CFD model. It was shown that the location of the vertical wall was directly related to the amount of separation as well as the separation characteristics. These findings support previous work and help guide future work for active flow control in a separated annular diffuser both computationally and experimentally.
|
4 |
Multiple intelligences theory in English language teaching: An analysis of current textbooks, materials and teachers’ perceptionsBotelho, Maria Do Rozário de Lima January 2003 (has links)
No description available.
|
Page generated in 0.0189 seconds