Doctor of Philosophy / The next generation mobile networks are expected to provide multimedia applications with a high quality of service. On the other hand, interference among multiple base stations (BS) that co-exist in the same location limits the capacity of wireless networks. In conventional wireless networks, the base stations do not cooperate with each other. The BSs transmit individually to their respective mobile stations (MS) and treat the transmission from other BSs as interference. An alternative to this structure is a network cooperation structure. Here, BSs cooperate with other BSs to simultaneously transmit to their respective MSs using the same frequency band at a given time slot. By doing this, we significantly increase the capacity of the networks. This thesis presents novel research results on a noncooperative transmission scheme and a cooperative transmission scheme for multi-user multiple-input-multiple-output orthogonal frequency division multiplexing (MIMO-OFDM). We first consider the performance limit of a noncooperative transmission scheme. Here, we propose a method to reduce the interference and increase the throughput of orthogonal frequency division multiplexing (OFDM) systems in co-working wireless local area networks (WLANs) by using joint adaptive multiple antennas(AMA) and adaptive modulation (AM) with acknowledgement (ACK) Eigen-steering. The calculation of AMA and AM are performed at the receiver. The AMA is used to suppress interference and to maximize the signal-to-interference-plus-noise ratio (SINR). The AM scheme is used to allocate OFDM sub-carriers, power, and modulation mode subject to the constraints of power, discrete modulation, and the bit error rate (BER). The transmit weights, the allocation of power, and the allocation of sub-carriers are obtained at the transmitter using ACK Eigen-steering. The derivations of AMA, AM, and ACK Eigen-steering are shown. The performance of joint AMA and AM for various AMA configurations is evaluated through the simulations of BER and spectral efficiency (SE) against SIR. To improve the performance of the system further, we propose a practical cooperative transmission scheme to mitigate against the interference in co-working WLANs. Here, we consider a network coordination among BSs. We employ Tomlinson Harashima precoding (THP), joint transmit-receive beamforming based on SINR (signal-to-interference-plus-noise-ratio) maximization, and an adaptive precoding order to eliminate co-working interference and achieve bit error rate (BER) fairness among different users. We also consider the design of the system when partial channel state information (CSI) (where each user only knows its own CSI) and full CSI (where each user knows CSI of all users) are available at the receiver respectively. We prove analytically and by simulation that the performance of our proposed scheme will not be degraded under partial CSI. The simulation results show that the proposed scheme considerably outperforms both the existing noncooperative and cooperative transmission schemes. A method to design a spectrally efficient cooperative downlink transmission scheme employing precoding and beamforming is also proposed. The algorithm eliminates the interference and achieves symbol error rate (SER) fairness among different users. To eliminate the interference, Tomlinson Harashima precoding (THP) is used to cancel part of the interference while the transmit-receive antenna weights cancel the remaining one. A new novel iterative method is applied to generate the transmit-receive antenna weights. To achieve SER fairness among different users and further improve the performance of MIMO systems, we develop algorithms that provide equal SINR across all users and order the users so that the minimum SINR for each user is maximized. The simulation results show that the proposed scheme considerably outperforms existing cooperative transmission schemes in terms of the SER performance and complexity and approaches an interference free performance under the same configuration. We could improve the performance of the proposed interference cancellation further. This is because the proposed interference cancellation does not consider receiver noise when calculating the transmit-receive weight antennas. In addition, the proposed scheme mentioned above is designed specifically for a single-stream multi-user transmission. Here, we employ THP precoding and an iterative method based on the uplink-downlink duality principle to generate the transmit-receive antenna weights. The algorithm provides an equal SINR across all users. A simpler method is then proposed by trading off the complexity with a slight performance degradation. The proposed methods are extended to also work when the receiver does not have complete Channel State Informations (CSIs). A new method of setting the user precoding order, which has a much lower complexity than the VBLAST type ordering scheme but with almost the same performance, is also proposed. The simulation results show that the proposed schemes considerably outperform existing cooperative transmission schemes in terms of SER performance and approach an interference free performance. In all the cooperative transmission schemes proposed above, we use THP to cancel part of the interference. In this thesis, we also consider an alternative approach that bypasses the use of THP. The task of cancelling the interference from other users now lies solely within the transmit-receive antenna weights. We consider multiuser Gaussian broadcast channels with multiple antennas at both transmitter and receivers. An iterative multiple beamforming (IMB) algorithm is proposed, which is flexible in the antenna configuration and performs well in low to moderate data rates. Its capacity and bit error rate performance are compared with the ones achieved by the traditional zero-forcing method.

This dissertation provides a study of synchronization and quantization issues in implementing a multistage receiver in fixed-point Digital Signal Processing (DSP) hardware. Current multistage receiver analysis has neglected the effects of synchronization and quantization; however, these effects can degrade system performance and therefore decrease overall system capacity. The first objective is to analyze and simulate various effects of synchronization in a multistage system. These effects include the effect of unsynchronized users on the bit error rate (BER) of synchronized users, and determining whether interference cancellation can be used to improve the synchronization time. This information is used to determine whether synchronization will limit overall system capacity. Both analytical and simulation techniques are presented. The second objective is to study the effects of quantization on the performance of the multistage receiver. A DSP implementation of a practical receiver will require a DSP chip with a fewer number of bits than the computer chips typically used in simulation of receiver performance. Therefore, the DSP implementation performs poorer than the simulation results predict. In addition, a fixed-point implementation is often favored over a floating-point implementation, due to the high processing requirements necessitated by the high chip rate. This further degrades performance because of the limited dynamic range available with fixed-point arithmetic. The performance of the receiver using a fixed-point implementation is analyzed and simulated. We also relate these topics to other important issues in the hardware implementation of multistage receivers, including the effects of frequency offsets at the receiver and developing a multiuser air protocol interface (API). This dissertation represents a contribution to the ongoing hardware development effort in multistage receivers at Virginia Tech. / Ph. D.

ITC/USA 2005 Conference Proceedings / The Forty-First Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2005 / Riviera Hotel & Convention Center, Las Vegas, Nevada / This paper describes and interference cancellation technique appropriate for ARTM Tier-1 waveforms. The technique requires the estimators for the bit sequences for the adjacent channels as well as the power levels of the adjacent channels. Simulation results show that the interference canceller allows a more dense “channel packing” thereby creating a channel utilization 67% ~ 100% greater than the current IRIG 106 recommendations.

No description available.

No description available.

No description available.

In wireless networking, receivers are typically assumed to be utilizing single-user decoding. Still, for more than twenty years we know that we can take advantage of interference by multi-user decoding. The Interference Cancellation (IC) technique has, of late, gained interest in the wireless networking context. Previous works [3] have shown considerable potential gains by leveraging optimal collaborative rate control to enable IC, focusing on the low Signal-to-Noise Ratio (SNR) regime. Here, we present centralized and distributed rate control algorithms, enabling IC, to increase system throughput. We consider a system where the receivers can apply multi-user decoding to perform IC and the rates are provided by a step-wise function of the Signal to Interference-and-Noise Ratio (SINR), in realistic conditions. We conduct a thorough simulation study comparing the proposed algorithms using two IC techniques, and deliver results that indicate significant system throughput gains.

This paper discusses the direct product cancellation of digraphs. We define the exact conditions on G such that GxK=HxK implies G=H. We focus first on simple equations such as GxK_2=HxK_2 where K_2 denotes a single arc and then extend this to the more general situation, GxK = HxK. Our results are achieved by using a “factorial” operation on graphs, which is in some sense analogous to the factorial of an integer.

Master of Engineering by Research / As a multi-carrier modulation scheme, Orthogonal Frequency Division Multiplexing (OFDM) technique can achieve high data rate in frequency-selective fading channels by splitting a broadband signal into a number of narrowband signals over a number of subcarriers, where each subcarrier is more robust to multipath. The wireless communication system with multiple antennas at both the transmitter and receiver, known as multiple-input multiple-output (MIMO) system, achieves high capacity by transmitting independent information over different antennas simultaneously. The combination of OFDM with multiple antennas has been considered as one of most promising techniques for future wireless communication systems. The challenge in the detection of a space-time signal is to design a low-complexity detector, which can efficiently remove interference resulted from channel variations and approach the interference-free bound. The application of iterative parallel interference canceller (PIC) with joint detection and decoding has been a promising approach. However, the decision statistics of a linear PIC is biased toward the decision boundary after the first cancellation stage. In this thesis, we employ an iterative receiver with a decoder metric, which considerably reduces the bias effect in the second iteration, which is critical for the performance of the iterative algorithm. Channel state information is required in a MIMO-OFDM system signal detection at the receiver. Its accuracy directly affects the overall performance of MIMO-OFDM systems. In order to estimate the channel in high-delay-spread environments, pilot symbols should be inserted among subcarriers before transmission. To estimate the channel over all the subcarriers, various types of interpolators can be used. In this thesis, a linear interpolator and a trigonometric interpolator are compared. Then we propose a new interpolator called the multi-tap method, which has a much better system performance. In MIMO-OFDM systems, the time-varying fading channels can destroy the orthogonality of subcarriers. This causes serious intercarrier interference (ICI), thus leading to significant system performance degradation, which becomes more severe as the normalized Doppler frequency increases. In this thesis, we propose a low-complexity iterative receiver with joint frequency- domain ICI cancellation and pilot-assisted channel estimation to minimize the effect of time-varying fading channels. At the first stage of receiver, the interference between adjacent subcarriers is subtracted from received OFDM symbols. The parallel interference cancellation detection with decision statistics combining (DSC) is then performed to suppress the interference from other antennas. By restricting the interference to a limited number of neighboring subcarriers, the computational complexity of the proposed receiver can be significantly reduced. In order to construct the time variant channel matrix in the frequency domain, channel estimation is required. However, an accurate estimation requiring complete knowledge of channel time variations for each block, cannot be obtained. For time- varying frequency-selective fading channels, the placement of pilot tones also has a significant impact on the quality of the channel estimates. Under the assumption that channel variations can be approximated by a linear model, we can derive channel state information (CSI) in the frequency domain and estimate time-domain channel parameters. In this thesis, an iterative low-complexity channel estimation method is proposed to improve the system performance. Pilot symbols are inserted in the transmitted OFDM symbols to mitigate the effect of ICI and the channel estimates are used to update the results of both the frequency domain equalizer and the PICDSC detector in each iteration. The complexity of this algorithm can be reduced because the matrices are precalculated and stored in the receiver when the placement of pilots symbols is fixed in OFDM symbols before transmission. Finally, simulation results show that the proposed MIMO-OFDM iterative receiver can effectively mitigate the effect of ICI and approach the ICI-free performance over time-varying frequency-selective fading channels.

Sinusoidal oscillator is intensively used in many applications, such as built-in-self-testing and ADC characterization. An innovative medical application for skin cancer detection employed a technology named bio-impedance spectroscopy, which also requires highly linear sinusoidal-wave as the reference clock. Moreover, the generated sinusoidal signals should be tunable within the frequency range from 10kHz to 10MHz, and quadrature outputs are demanded for coherent demodulation within the system. A design methodology of sinusoidal oscillator named digital-harmonic-cancellation (DHC) technique is presented. DHC technique is realized by summing up a set of square-wave signals with different phase shifts and different summing coefficient to cancel unwanted harmonics. With a general survey of literature, some sinusoidal oscillators based on DHC technique are reviewed and categorized. Also, the mathematical algorithm behind the technique is explained, and non-ideality effect is analyzed based on mathematical calculation. The prototype is fabricated in OnSemi 0.5um CMOS technology. The experimental results of this work show that it can achieve HD2 is -59.74dB and HD3 is -60dB at 0.9MHz, and the frequency is tunable over 0.1MHz to 0.9MHz. The chip consumes area of 0.76mm2, and power consumption at 0.9MHz is 2.98mW. Another design in IBM 0.18um technology is still in the phase of design. The preliminary simulation results show that the 0.18um design can realize total harmonic distortion of -72dB at 10MHz with the power consumption of 0.4mW. The new design is very competitive with state-of-art, which will be finished with layout, submitted for fabrication and measured later.