No description available.

Tires are the most influential component of the vehicle as they constitute the only contact between the vehicle and the road and have to generate and transmit forces necessary for the driver to control the vehicle. Hydroplaning is a phenomenon which occurs when a layer of water builds up between the tires of a vehicle and the road surface which leads to loss of traction that prevents the vehicle from responding to control inputs such as steering, braking or acceleration. It has become an extremely important factor in the automotive and tire industry to study the factors affecting vehicle hydroplaning. Nearly 10-20% of road fatalities are caused by lack of traction on wet surfaces. The tire tread pattern, load, inflation pressure, slip and camber angles influence hydroplaning to a great extent. Finite Element Analysis, although computationally expensive, provides an excellent way to study such Fluid Structure Interactions (FSI) between the tire-water-road surfaces. Abaqus FSI CEL approach has been used to study tire traction with various vehicle configurations. The tire force data obtained from the Finite Element simulations is used to develop a full vehicle hydroplaning model by integrating the relevant outputs with the commercially available vehicle dynamics simulation software, CarSim. / Master of Science

In any automotive system, the tires play a very crucial role in defining both the safety and performance of the vehicle. The interaction between the tire and the road surface determines the vehicle's ability to accelerate, decelerate and steer. Having information about this interaction in real-time can be very valuable for the on-board advanced active safety systems to mitigate the risks ahead of time and keep the vehicle stable. The crucial information which can be obtained from the tire includes but are not limited to tire-road friction, tire forces (longitudinal, lateral), normal load, road surface characteristics and tire pressure. This information can be acquired through indirect vehicle dynamics based estimation algorithms or through direct measurements using sensors inside the tire. However, the indirect estimations fail to give an accurate measure of the vehicle state in certain conditions (e.g. side winds, road banking, surface change) and require ABS or VSC activation before the estimation begins. Therefore, to improve the performance of these active stability systems, direct measurement based approaches must be explored. This research expands the applications of Intelligent tire and focuses on using the sensor based measurement approach to develop estimation algorithms relating to tire force measurement. A tri-axial accelerometer is attached to the inner liner of the tire (Intelligent Tire) and two of such tires are placed on an instrumented (MSW, VBox, IMU, Encoders) VW Jetta. Different controlled tests are carried out on the instrumented vehicle and the Intelligent tire signal is analyzed to extract features related to the tire forces and pressure. Due to unavailability of direct force measurements at the wheel, a VW Jetta simulation model is developed in CarSim and the extracted features are validated with a good correlation. / Master of Science

Automotive and Tire companies spend extensive amounts of time and money to tune their products through prototype testing at dedicated test facilities. This is mainly due to the limitations in the simulation capabilities that exist today. With greater competence in simulation, comes more control over designs in the initial stages, which in turn lowers the demand on the expensive stage of tuning. The work presented, aims at taking today's simulation capabilities a step forward by integrating models that are best developed in different software interfaces. An in-plane rigid ring model is used to understand the transient response of tires to various high frequency events such as Anti-Lock Braking and short wavelength road disturbances. A rule based ABS model performs the high frequency braking operation. The tire and ABS models have been created in the Matlab-Simulink environment. The vehicle model has been developed in CarSim. The models developed in Simulink have been integrated with the vehicle model in CarSim, in the form of a design tool that can be used by tire as well as vehicle designers for further tuning of the vehicle functional performances as they relate to in-line braking scenarios. Outdoor validation tests were performed to obtain data from a vehicle that was measured on a suspension parameter measuring machine (SPMM) in order to complement this design tool. The results of the objective tests performed have been discussed and the correlations and variations with respect to the simulation results have been analyzed. / Master of Science

With the advent of faster computer processors and better optimization algorithms, Model Predictive Control (MPC) systems are more readily used for real-time applications. This research focuses on the application of MPC to trajectory generation of autonomous vehicles in an online manner. The operating environment is assumed to be unknown with various different types of obstacles. Models of simplified 2-D dynamics of the vehicle are developed, discretized and validated against a nonlinear CarSim vehicle model. The developed model is then used to predict future states of the vehicle. The relationship of the weight transfer to the tire slip angle is investigated. The optimal trajectory tracking problem is formulated in terms of a cost function minimization with constraints. Initially, a gradient descent method is used to minimize the cost function. A MATLAB based MPC controller is developed and interfaced with CarSim in order to test the controller on a vehicle operating in a realistic environment. The effects of varying MPC look-ahead horizon lengths on the computation time, simulation cost and the tracking performance are also investigated. Simulation results show that the new MPC controller provides satisfactory online obstacle avoidance and tracking performance. Also, a trajectory tracking criterion with goal point information is found to be superior to traditional trajectory tracking methods since they avoid causing the vehicle to retreat once a large obstacle is detected on the desired path. It is further demonstrated that at a controller frequency of 20Hz, the implementation is real-time implementable only at shorter horizon lengths. / UOIT

The suspension system is one of the most sensitive systems of a vehicle as it affects the dynamic behavior of the vehicle with even minor changes. These systems are designed to carry out multiple tasks such as isolating the vehicle body from the road/tire vibrations as well as achieving desired ride and handling performance levels in both steady state and limit handling conditions. The damping coefficient of the damper plays a crucial role in determining the overall frequency response of the suspension system. Considerable research has been carried out on semi active damper systems as the damping coefficient can be varied without the system requiring significant external power giving them advantages over both passive and fully active suspension systems. Dampers behave as non-linear systems at higher frequencies and hence it has been difficult to develop accurate models for its full range of motion. This study aims to develop a velocity sensitive damper model using artificial neural networks and essentially provide a 'black-box' model which encapsulates the non-linear behavior of the damper. A feed-forward neural network was developed by testing a semi active damper on a shock dynamometer at CenTiRe for multiple frequencies and damping ratios. This data was used for supervised training of the network using MATLAB Neural Network Toolbox. The developed NN model was evaluated for its prediction accuracy. Further, the developed damper model was analyzed for feasibility of use for simulations and controls by integrating it in a Simulink based quarter car model and applying the well-known skyhook control strategy. Finally, effects on ride and handling dynamics were evaluated in Carsim by replacing the default damper model with the proposed model. It was established that this damper modeling technique can be used to help evaluate the behavior of the damper on both component as well as vehicle level without needing to develop a complex physics based model. This can be especially beneficial in the earlier stages of vehicle development. / Master of Science

Cross median crashes have become a serious problem in recent years. Most of the median cross sections used for divided highways have terrains with steep slopes. Traffic barriers, frequently used on slopes, are generally designed based on the findings obtained from crash tests performed on flat terrain. For barriers placed on roadside and median slopes, vehicle impact height varies depending on the trajectory of the vehicle along the ditch section and lateral offset of the barrier. Thus depending on the placement location on a relatively steep slope, a barrier can be impacted by an errant vehicle at height and orientation more critical compared to those considered during its design. Hence, detailed study of performance of barriers on roadside and median slopes is needed to achieve acceptable safety performance. In this study, performances of modified G4(1S) W-beam, Midwest Guardrail System (MGS), modified Thrie-beam, modified weak post W-beam, and box-beam guardrail systems on sloped terrains are investigated using numerical simulations. A procedure is developed that provide guidance for their placement on roadside and median slopes. The research approach consists of nonlinear finite element analyses and multi-rigid-body dynamic analyses approach. Detailed finite element representation for each of the barriers is developed using LS-DYNA. Model fidelity is assessed through comparison of simulated and measured responses reported in full scale crash test studies conducted on flat terrain. LS-DYNA simulations of vehicle impacts on barriers placed on flat terrain at different impact heights are performed to identify performance limits of the barriers in terms of acceptable vehicle impact heights. The performances of the barriers are evaluated following the guidelines provided in NCHRP Report 350. Multi-rigid-body dynamic analysis code, CARSIM, is used to identify trajectories of the vehicles traversing various roadside and median cross-slopes. After analyzing vehicle trajectories and barrier performance limits, a guideline has been prepared with recommendations for the placement of barriers along roadside and median slopes. This guideline is then verified and refined using the responses obtained from full-scale LS-DYNA simulations. These simulations capture the full encroachment event from departure of the vehicle off the traveled way through impact with the barrier.

No description available.