The demand for energy storage technologies is rapidly increasing in portable electronics, transportation, and renewable energy systems. Thus, the objective of this research is to develop and enhance the performance of Ni-based electrochemical supercapacitors by optimizing synthesis conditions and design of the electrode materials. Conventional and on-chip supercapacitors were developed with notable performance enhancement. For conventional supercapacitors, a uniform and conformal coating process was developed to deposit Ni(OH)2 nanoflakes on carbon microfibers in-situ by a simple chemical bath deposition at room temperature. The microfibers conformally-coated with Ni(OH)2 make direct physical contacts with essentially every single nanoflakes, leading to more efficient electron transport. Using this strategy, we have achieved devices that exhibit five times higher specific capacitance compared to planar (non-conformal) Ni(OH)2 nanoflakes electrodes prepared by drop casting of Ni(OH)2 on the carbon microfibers (1416 F/g vs. 275 F/g). For on-chip storage applications, microfabricated supercapacitors were developed using a combination of top-down photolithography and bottom-up CBD. The resulting Ni(OH)2 micro-supercapacitors show high-rate redox activity up to 500 V/s and an areal cell capacitance of 16 mF/cm2 corresponding to a volumetric stack capacitance of 325 F/cm3. This volumetric capacitance is 2-fold higher than carbon and metal oxide based micro-supercapacitors. Furthermore, these micro-supercapacitors show a maximum energy density of 21 mWh/cm3, which is superior to the Li-based thin film batteries. To enhance cycling stability, Ni-Cu-OH and Ni-Co-OH ternary electrodes have been prepared with different Ni:Cu and Ni:Co ratios by CBD at room temperature on carbon microfibers. It is observed that the electrodes with Ni:Cu and Ni:Co composition ratio of 100:10 results in an optimum capacitance and cycling stability. For the optimum composition, Ni-Co-OH with graphene and carbon nanofibers electrode was tested, with resultant improvement in electrode potential window, equivalent series resistance, and cyclic stability. To further increase energy density, Ni(OH)2//Graphene asymmetric supercapacitor were fabricated with areal capacitance of 253 mF/cm2 at 5 mA/cm2 which is higher than NiO//rGO prepared by hydrothermal method. Ni-Co-OH/G-CNF//Graphene asymmetric supercapacitor results in a maximum power of 23 mW within an operating voltage of 2.2 V which are higher than of Ni(OH)2//Graphene (15.94 mW within 1.8 V). Our asymmetric supercapacitors have flexible-electrodes, low-cost fabrication process and environmentally friendly materials.

京都大学 / 0048 / 新制・課程博士 / 博士(エネルギー科学) / 甲第21190号 / エネ博第364号 / 新制||エネ||71(附属図書館) / 京都大学大学院エネルギー科学研究科エネルギー基礎科学専攻 / (主査)教授 佐川 尚, 教授 森井 孝, 教授 松田 一成 / 学位規則第4条第1項該当 / Doctor of Energy Science / Kyoto University / DGAM

No description available.

No description available.

No description available.

No description available.

No description available.

Carbon nanotubes (CNTs) have extraordinary electrical and mechanical properties, and many potential applications have been proposed, ranging from nanoscale devices to reinforcement of macroscopic structures. However, due to their small sizes, characterization of their mechanical properties and deformation behaviours are major challenges. Theoretical modelling of deformation behaviours has shown that multi-walled carbon nanotubes (MWCNTs) can develop ripples in the walls on the contracted side when bent above a critical curvature. The rippling is reversible and accompanied by a reduction in the bending stiffness of the tubes. This behaviour will have implications for future nanoelectromechanical systems (NEMS). Although rippling has been thoroughly modelled there has been a lack of experimental data thus far. In this study, force measurements have been performed on individual MWCNTs and vertically aligned carbon nanofibers (VACNFs). This was accomplished by using a custom-made atomic force microscope (AFM) inside a scanning electron microscope (SEM). The measurements were done by bending free-standing MWCNTs/VACNFs with the AFM sensor in a cantilever-to-cantilever fashion, providing force-displacement curves. From such curves and the MWCNT/VACNF dimensions, measured from SEM-images, the critical strain for the very onset of rippling and the Young’s modulus, E, could be obtained. To enable accurate estimations of the nanotube diameter, we have developed a model of the SEM-image formation, such that intrinsic diameters can be retrieved. We have found an increase in the critical strain for smaller diameter tubes, a behaviour that compares well with previous theoretical modelling. VACNFs behaved very differently, as they did not display any rippling and had low bending stiffnesses due to inter-wall shear. We believe that our findings will have implications for the design of future NEMS devices that employ MWCNTs and VACNFs. / <p>Artikel 2 Image formation mechanisms tidigare som manuskript, nu publicerad: urn:nbn:se:kau:diva-16425 (MÅ 150924)</p>

The objective of this work is to electrospin poly(acrylonitrile) (PAN) based nanofibers with controlled diameter and to stabilize and carbonize them for developing meso-porous carbon for application as electrochemical capacitor electrodes. A sacrificial polymer, poly(styrene-co-acrylonitrile) (SAN) has been used to control porosity. Carbon nanotubes (CNT) have been used to increase electrode conductivity and hence power density. The study has been divided into two parts. In part I, electrospinning behavior of PAN and PAN/CNT has been studied. The diameter of electrospun PAN fibers was monitored as a function of polymer molecular weight, solution concentration, solution flow rate, distance between the spinneret and the target, and the applied voltage. Bead free PAN fibers of 60 nm diameter have been electrospun. Various electrospun fibers have been characterized by wide angle X-ray diffraction and by Raman spectroscopy. Electrospinning process has been observed by high speed photography. In part II, the electrospun PAN, PAN/SAN, and PAN/SAN/CNT fiber mats were stabilized, carbonized, and processed into electrochemical capacitor electrodes. The performance of the electrochemical capacitors was tested by the constant current charge/discharge and cyclic voltammetry in 6 molar potassium hydroxide aqueous solution. The surface area and pore size distribution of the electrodes were measured using N2 adsorption and desorption. The effect of surface area and pore size distribution on the capacitance performance has been studied. The capacitance performance of various carbonized electrospun fibers mats have been compared to those of the PAN/SAN/CNT film, carbon nanotube bucky paper, and activated carbon pellet. The capacitance of PAN/SAN/CNT fiber mat over 200 F/g (at a current density of 1 A/g) and the power density approaching 1 kW/kg have been observed. Addition of 1 wt% carbon nanotubes in PAN/SAN, improves the power density by a factor of four. For comparison, the capacitance of single wall carbon nanotube bucky paper at a current density of 1 A/g is about 50 F/g.

Issues with the dissolution and diffusion of polysulfides in liquid organic electrolytes hinder the advance of lithium–sulfur (Li-S) batteries for next generation energy storage. To trap and re-utilize the polysulfides, brush-like, zinc oxide (ZnO) nanowires based interlayers were prepared ex-situ using a wet chemistry method and were coupled with a sulfur/multi-walled carbon nanotube (S/MWCNT) composite cathode. The cell with this configuration showed a good cycle life at a high current rate ascribed to (a) a strong interaction between the polysulfides and ZnO nanowires grown on conductive substrates; (b) fast electron transfer and (c) an optimized ion diffusion path from a well-organized nanoarchitecture. A praline-like flexible interlayer consisting of titanium oxide (TiO2) nanoparticles and carbon (C) nanofiber was further prepared in-situ using an electrospinning method, which allows the chemical adsorption of polysulfides throughout a robust conductive film. A significant enhancement in cycle stability and rate capability was achieved by incorporating this interlayer with a composite cathode of S/MWCNT. These results herald a new approach to building functional interlayers by integrating metal oxides with conductive frameworks. The derivatives of the TiO2/C interlayer was synthesized by changing the precursor concentration and carbonization temperature. Finally, a dual-interlayer was fabricated by simply coating titanium nitride (TiN) nanoparticles onto an electro-spun carbon nanofiber mat, which was then sandwiched with a sulfur/assembled Ketjen Black (KB) composite cathode with an ultra-high sulfur loading. The conductive polar TiN nanoparticles not only have a strong chemical affinity to polysulfides through a specific sulfur-nitrogen bond but also improve the reaction kinetics of the cell by catalyzing the conversion of the long-chain polysulfides to lithium sulfide. Besides, carbon nanofiber mat ensures mechanical robustness to TiN layer and acts as a physical barrier to block polysulfides diffusion. The incorporation of dual interlayers with sulfur cathodes offers a commercially feasible approach to improving the performance of Li-S batteries.