Carbon fabric-reinforced polymer (CFRP) composites are widely used in aerospace, automotive and construction structures thanks to their high specific strength and stiffness. They can also be used in various products in sports industry. Such products can be exposed to different in-service conditions such as large bending deformations caused by quasi-static and dynamic loading. Composite materials subjected to such bending loads can demonstrate various damage modes - matrix cracking, delamination and, ultimately, fabric fracture. Damage evolution in composites affects both their in-service properties and performance that can deteriorate with time. Such damage modes need adequate means of analysis and investigation, the major approaches being experimental characterisation and numerical simulations. This work deals with a deformation behaviour and damage in carbon fabric-reinforced polymer (CFRP) laminates caused by quasi-static and dynamic bending. Experimental tests are carried out first to characterise the behaviour of a CFRP material under tension, in-plane shear and large-deflection bending in quasi-static conditions. The dynamic behaviour of these materials under large-deflection bending is characterised by Izod-type impact tests employing a pendulum-type impactor. A series of impact tests is performed on the material at various impact energy levels up to its fracture, to obtain a transient response of the woven CFRP laminate. Microstructural examination of damage is carried out by optical microscopy and X-ray micro computed tomography (Micro-CT). The damage analysis revealed that through thickness matrix cracking, inter-ply delaminations, intra-ply delamination such as tow debonding, and fabric fracture was the prominent damage modes. These mechanical tests and microstructural studies are accompanied by advanced numerical models developed in a commercial code Abaqus. Among those models are (i) 2D FE models to simulate experimentally observed inter-ply delamination, intra-ply fabric fracture and their subsequent interaction under quasi-static bending conditions and (ii) 3D FE models based on multi-body dynamics used to analyse interacting damage mechanisms in CFRP under large-deflection dynamic bending conditions. In these models, multiple layers of bilinear cohesive-zone elements are placed at the damage locations identified in the Micro CT study. Initiation and progression of inter-laminar delamination and intra-laminar ply fracture are studied by employing cohesive elements. Stress-based criteria are used for damage initiation while fracture-mechanics techniques are employed to capture its progression in composite laminates. The developed numerical models are capable to simulate the studied damage mechanisms as well as their subsequent interaction observed in the tests and microstructural damage analysis. In this study, a novel damage modelling technique based on the cohesive-zone method is proposed for analysis of interaction of various damage modes, which is more efficient than the continuum damage mechanics approach for coupling between failure modes. It was observed that the damage formation in the specimens was from the front to the back at the impact location in the large-deflection impact tests, unlike the back-to-front one in drop-weight tests. The obtained results of simulations showed a good agreement with experimental data, thus demonstrating that the proposed methodology can be used for simulations of discrete damage mechanisms and their interaction during the ultimate fracture of composites in bending. The main outcome of this thesis is a comprehensive experimental and numerical analysis of the deformation and fracture behaviours of CFRP composites under large-deflection bending caused by quasi-static and dynamic loadings. Recommendations on further research developments are also suggested.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: This study set out to determine the debonding of externally applied Carbon Fibre Reinforced Polymer (CFRP) plates from RC structures under cyclic loading. Triplet shear tests and finite element (FE) analyses were done on the epoxy to determine the bond stress between the CFRP plate and a reinforced concrete specimen. From these tests and analyses the average shear strength of the bond between the epoxy and concrete substrate was determined and the shear strength of the epoxy specified by the supplier could be confirmed. A case study of a statically loaded beam was performed to verify the bond strength. Finally a reinforced concrete (RC) T-section was designed and pre-cracked to simulate a damaged beam in practice. These sections were then externally reinforced by bonding CFRP plates onto the face of the web. The sections were subjected to static and cyclic loading at different force amplitudes. Along with the experimental tests, FE models were developed and analysed which had the same geometrical and material properties as the experimental specimens. Due to time constraint a FE mesh objectivity study was not done, but the chosen element size is believed to be sufficiently small to replicate the experimental tests objectively. The FE analyses and the experimental tests yielded results that were close to each other on both the global scale and in terms of localised behaviour, thus it was decided that the computational approach could be used for the final design of a model of the debonding of CFRP plates bonded onto RC beams under cyclic loading because the data can be analysed more easily and a large variation of tests can be done. For the T-section 3 tests were conducted; a pull-off (static) test where the bonded CFRP plate was pulled from a specimen to get the ultimate failure envelope of the test specimens. The static test was followed by cyclic tests with force amplitude of 85% and 65% of the ultimate pull-off strength. Different measurements were taken to get the global and local displacement behaviour of the section. The global displacement was measured by means of a linear variable displacement transducer (LVDT, displacement meter) clamped onto the CFRP plate that pushed on the top of the concrete and the local displacement was measured with the help of the Aramis system. The displacement was then compared to the same displacements of nodes and elements in the FE models. The result was a confirmation that the results from the FE models were sufficient to design a model for cyclic debonding of CFRP plates from RC structures. From the FE models the relative displacement between the CFRP plate and concrete was obtained in the vicinity of a crack. This relative displacement was then normalised by the respective stress range of the different tests, from which the normalised relative displacement was plotted against the number of cycles to get an equation limiting the number of cycles for a specific stress range. From the results, it appears that for cyclic load levels up to 65% of the peak static resistance, a threshold number of load cycles are required for delamination initiation. Subsequently, a near constant delamination rate is reached. The delamination rate is significantly lower for lower cyclic load levels. Finally, an unstable delamination stage is reached at a level of about 65 μm for all the analyses, after which CFRP pull-off is imminent. Service life design of CFRP reinforcement of RC beams should take into consideration the delamination initiation threshold, the subsequent delamination rate and finally the initiation of unstable delamination. / AFRIKAANSE OPSOMMING: Die projek is uitgevoer om die delaminasie van ekstern aangewende Koolstof Vesel Versterkte Polimeer (KVVP) stroke op gewapende beton strukture te bepaal onder sikliese belasting. Triplet skuif toetse is gedoen op die gebruikte epoksie om die verband-sterkte te bepaaltussen die KVVP stroke en die beton proefstuk. Die skuif toetse is ook met behulp van die eindige element (EE) metode geanaliseer. Die resultaat van die toetse en analises het gewys dat die verband sterkte tussen die KVVP stroke en beton gelyk is aan die skuif sterkte van die epoksie wat verskaf is. `n Gevalle studie van `n monotonies belaste balk is gedoen om die verband-sterkte te verifieër. `n Gewapende beton T-snit is ontwerp en voor-af gekraak om `n beskadigde balk in die praktyk voor te stel. Die beskadigde proefstukke is vervolgens ekstern versterk met KVVP stroke wat aan die web van die T-snit vas geplak is. Die versterkte T-snitte is getoets onder statiese en sikliese belasting. Die sikliese toetse is ook onder verskillende spanningsamplitudes getoets. Om die eksperimentele toetse te verifieër is EE modelle gebou en geanaliseer wat dieselfde geometriese en materiaal eienskappe as die eksperimentele proefstukke gehad het, maar as gevolg van `n tydsbeperking is `n sensitiwiteit studie oor die element grootte nie gedoen nie. Die element grootte is klein genoeg gekies en word beskou as voldoende om die gedrag objektief te simuleer. Die EE analises en eksperimentele resultate was na genoeg aan mekaar op beide globale en lokale vlak. Dus is `n analitiese benadering tot die toetse vervolgens gebruik vir die ontwerp van `n model vir delaminasie van KVVP stroke van gewapende beton strukture onder sikliese belasting. Die EE metode stel die analis in staat om `n verskeidenheid van toetse relatief vinnig uit te voer en om die data van die toetse vinniger te interpreteer as deur fisiese eksperimentele toetse. Drie eksperimente is uitgevoer op die T-snitte, `n aftrek-toets (staties) waar die KVVP strook van `n proefstuk afgetrek is om die falingsomhullende diagram te kry en dan ook twee sikliese toetse teen 85% en 65% van die krag amplitude van die falingskrag. Verplasingsmeters is gebruik om die globale verplasing te kry, deur dit vas te klamp op die KVVP strook en dan die verplasing te meet relatief tot die bokant van die beton. Die lokale veplasing is met behulp van die Aramis sisteem verkry. Die eksperimentele verplasings is dan vergelyk met verplasings van die ooreenstemmende nodes en elemente in die EE modelle. Deur die vergelyking van die resultate is dit bevestig dat die eindige element modelle voldoende is om die model vir sikliese delaminasie van KVVP stroke van gewapende beton strukture te gebruik vir die ontwerp. Uit die EE modelle is die relatiewe verplasing tussen die KVVP strook en die beton gekry in die omgewing van `n kraak. Die relatiewe verplasing is genormaliseer deur elkeen se spanningsamplitude. Die genormaliseerde relatiewe verplasing is dan teenoor die aantal siklusse geteken waarvan `n vergelyking vir die maksimum verplasing afgelei is om die aantal siklusse vir `n gegewe spanning amplitude te beperk. Uit die resultate blyk dit dat vir sikliese laste tot en met 65% van die piek statiese weerstand `n aantal siklusse moontlik is voordat delaminasie begin waarna `n konstante delaminasie tempo bereik word. Die delaminasie tempo is stadiger vir sikliese laste teen `n laer belastings amplitude. Laastens word `n onstabiele delaminasie fase bereik by `n vlak van ongeveer 65 μm, na die oorgang delamineer die KVVP strook binne enkele siklusse. Die beginpunt van delaminasie, die delaminasie tempo en laastens die begin van onstabiele delaminasie moet in gedagte gehou word by die ontwerp diens leeftyd van KVVP versterkte gewapende beton balke.

Die Mischbauweise stellt eine Möglichkeit dar, insbesondere im Automobilbau, aber auch in anderen Industriezweigen Leichtbau zu betreiben. Dazu werden verschiedenartige Werkstoffe miteinander kombiniert. Vorzugsweise handelt es sich um Kombinationen aus faserverstärkten Kunststoffen und Leichtmetallen. Nach dem Motto “Der richtige Werkstoff am richtigen Ort” können so belastbare und gleichzeitig leichte Konstruktionen realisiert werden. Eine große Herausforderung besteht dabei jedoch im Fügen solch unterschiedlicher Werkstoffe. Aufgrund großer Unterschiede in Bindungsart und Schmelztemperatur sind klassische Fügeverfahren nicht anwendbar. Zum Verbinden von Metallen mit Faser- Verbund-Werkstoffen (FKV) wurden deswegen vorhandene Technologien adaptiert oder neue entwickelt. Im Rahmen dieser Dissertation wurde mit dem modifizierten Blindnieten ein neuer Lösungsansatz entwickelt, der sowohl mechanische als auch thermische Fügeverfahren miteinander kombiniert. Dazu wird ein rotierender Blindniet in sich überlappende Bleche getrieben und das darunter liegende Material unter Ausbildung einer Hülse aus dem Oberblech verdrängt. Anschließend wird der Niet ausgeformt und der Prozess ist abgeschlossen. Durch die Reibwärme wird die thermoplastische Matrix des FKV geschmolzen und die Fasern werden beweglich und können verdrängt werden. Dadurch kommt es zu einer geringeren Faserschädigungen und es können Delaminationen komplett vermieden werden. Untersuchungen wurden vorzugsweise an Materialkombinationen in Mischbauweise durchgeführt. Es wurden Aluminium- und Magnesiumbleche mit verschiedenen FKV mit Glas- oder Kohlefaserverstärkung gefügt. Für eine große Anwendungsbreite wurden ebenso Verbindungen von mehreren Metallblechen untersucht. Alle Kombinationen konnten so gefügt werden, dass in relativ kurzer Prozesszeit eine qualitativ hochwertige Verbindung entsteht. Mit einer geeigneten Parameterwahl sind Fügezeiten unter drei Sekunden möglich. Die mechanisch technologischen Gütewerten zeigen, dass mittels modifiziertem Blindnieten hergestellte Verbindungen mindestens die gleiche Lasten aufnehmen können, wie konventionelle Verfahren. Unter Scherbelastung kann die Belastbarkeit um bis zu 68 % gesteigert werden. Es hat sich gezeigt, dass mit dem neuen Verfahren eine wirtschaftliche Lösung für den Mischbau zur Verfügung steht. / Composite constructions provide an opportunity to introduce lightweight design in automotive and other industries. Therefore different kind of materials are combined. Preferably, these are combinations of fibre reinforced plastics and lightweight metal alloys. With the slogan "the right material at the right place" tough and lightweight constructions can be realized. A big challenge the joining of these different materials. Because of big differences in the chemical bindings and in the melting temperature, conventional joining methods cannot be used. To join fibre reinforced plastics (FRP) existing processes were adapted or newly developed. In the course of this work with the modified blind riveting a new approach was developed, which combines mechanical and thermal joining processes. Therefore a rotating blind rivet is penetrated through two overlapping sheets by deforming the sheet material. After that the rivet is set and the process finished. Because of the friction heat the thermoplastic matrix of the FRP is slightly melted and the fibres can be moved without breaking them. Investigations were done mainly with lightweight material combinations. Sheets made out of aluminum and magnesium were joined with glass or carbon fibre reinforced plastic sheets. For a wider application field also combinations of two metal sheets were investigated. All combinations could be joined in a relatively short cycle time and high quality. So it is possible to reach a joining time of under 3 seconds. Under shear load the strength of joints made by modified blind riveting can be up to 68 % higher than conventional riveted joints. It has been shown that the new process can be exploited economically.

An investigation on the application of basalt fibre reinforced polymer (BFRP) and carbon fibre reinforced polymer (CFRP) bars as longitudinal reinforcement for simple and continuous concrete slabs is presented. Eight continuously and four simply concrete slabs were constructed and tested to failure. Two continuously supported steel reinforced concrete slabs were also tested for comparison purposes. The slabs were classified into two groups according to the type of FRP bars. All slabs tested were 500 mm in width and 150 mm in depth. The simply supported slabs had a span of 2000 mm, whereas the continuous slabs had two equal spans, each of 2000 mm. Different combinations of under and over FRP (BFRP/CFRP) reinforcement at the top and bottom layers of slabs were investigated. The continuously supported BFRP and CFRP reinforced concrete slabs exhibited larger deflections and wider cracks than the counterpart reinforced with steel. The experimental results showed that increasing the bottom mid-span FRP reinforcement of continuous slabs is more effective than the top over middle support FRP reinforcement in improving the load capacity and reducing mid-span deflections. Design guidelines have been validated against experimental results of FRP reinforced concrete slabs tested. ISIS-M03-07 and CSA S806-06 equations reasonably predicted the deflections of the slabs tested. However, ACI 440-1R-06 underestimated the deflections, overestimated the moment capacities at mid-span and over support sections, and reasonably predicted the load capacity of the continuous slabs tested. On the analytical side, a numerical technique consisting of sectional and longitudinal analyses has been developed to predict the moment-curvature relationship, moment capacity and load-deflection of FRP reinforced concrete members. The numerical technique has been validated against the experimental test results obtained from the current research and those reported in the literature. A parametric study using the numerical technique developed has also been conducted to examine the influence of FRP reinforcement ratio, concrete compressive strength and type of reinforcement on the performance of continuous FRP reinforced concrete slabs. Increasing the concrete compressive strength decreased the curvature of the reinforced section with FRP bars. Moreover, in the simple and continuous FRP reinforced concrete slabs, increasing the FRP reinforcement at the bottom layer fairly reduced and controlled deflections.

O presente trabalho avaliou a influência dos concretos de ultra-alto desempenho com fibras (UHPFRC) e sem fibras (UHPC) no reforço de pilares curtos de concreto armado de seção transversal circular e quadrada. Avaliou-se também a adição de armaduras adicionais de reforço e de polímeros reforçados com fibras de carbono (PRFC) em alguns pilares reforçados. Para a avaliação deste novo sistema de reforço optou-se pela realização de um programa experimental e simulações numéricas. É importante ressaltar que no programa experimental, nenhum pilar reforçado possuía seção transversal maior que a seção do pilar de referência. Foi verificado por meio do programa experimental, que as camisas de UHPC apresentaram ruína de natureza frágil e não se recomenda a sua utilização a menos que acompanhada de mecanismos que garantam adequado confinamento do pilar reforçado. Nos pilares circulares e quadrados reforçados com UHPFRC foram verificados, respectivamente, incrementos de resistência de 106,4% e 83,6% onde o concreto do cobrimento foi substituído por UHPFRC, 154,3% e 111,7% onde além da substituição do cobrimento foram inseridas armaduras adicionais e 160% e 85,6% onde houve a colocação de PRFC após a substituição do cobrimento. Todos os pilares reforçados com UHPFRC não apresentaram destacamento da camisa de reforço. Foram realizadas simulações numéricas variando a espessura da camisa de UHPFRC e do número de camadas de PRFC tanto nos pilares de seção circular como nos pilares de seção quadrada. Por meio destas simulações, notou-se que a adição de pequenos incrementos de espessura da camisa de UHPFRC, proporciona elevados incrementos de resistência ao pilar reforçado, ao passo que o aumento do número de camadas de PRFC não influenciaria significantemente no incremento de resistência e sim na ductilidade do conjunto. / The present work evaluated the influence of ultra-high performance concrete with fibers (UHPFRC) and without fibers (UHPC) on the strengthening of short columns of reinforced concrete of circular and square cross section. It was also evaluated the addition of additional reinforcement and carbon fiber reinforced polymers (PRFC) on some strengthened columns. For the evaluation of this new system of strengthening we opted for the realization of an experimental program and numerical simulations. It is important to note that in the experimental program, no strengthened columns had a larger cross section than the reference column section. It was verified through the experimental program that the UHPC shirts presented ruin of a fragile nature and their use is not recommended unless accompanied by mechanisms that guarantee adequate confinement to the strengthened columns. In the circular and square columns strengthened with UHPFRC, respectively, resistance increments of 106.4% and 83.6% were verified, where the cover concrete was replaced by UHPFRC, 154.3% and 111.7%, in addition to the substitution of additional reinforcement were inserted and 160% and 85.6% where PRFC placement was performed after the replacement of the cover. All strengthened columns with UHPFRC did not present detachment of the strengthening jacket. Numerical simulations were performed by varying the thickness of the UHPFRC jacket and the number of PRFC layers on both the circular section columns and the square section columns. Through these simulations, it was noted that the addition of small thickness increments of the UHPFRC jacket would provide high increments of strength to the strengthened columns, while increasing the number of PRFC layers would not significantly influence the increase in strength but rather ductility of the assembly.

Mitigation of the blast risk associated with terrorist attacks and accidental explosions threatening critical infrastructure has become a topic of great interest in the civil engineering community, both in Canada and abroad. One method of mitigating blast risk is to retrofit vulnerable structures to resist the impulsive effects of blast loading. A comprehensive re-search program has been undertaken to develop fibre reinforced polymer (FRP) retrofit methodologies for structural and non-structural elements, specifically reinforced concrete slabs and walls, subjected to blast loading. The results of this investigation are equally valid for flexure dominant reinforced concrete beams subject to blast effects. The objective of the research program was to generate a large volume of research data for the development of blast-resistant design guidelines for externally bonded FRP retrofit systems. A combined experimental and analytical investigation was performed to achieve the objectives of the program. The experimental program involved the construction and simulated blast testing of a total of thirteen reinforced concrete wall and slab specimens divided into five companion sets. These specimens were subjected to a total of sixty simulated explosions generated at the University of Ottawa Shock Tube Testing Facility. Companion sets were designed to study one- and two-way bending, as well as the performance of specimens with simply-supported and fully-fixed boundary conditions. The majority of the specimens were retrofitted with externally bonded carbon fibre reinforced polymer (CFRP) sheets to improve overall load-deformation characteristics. Specimens within each companion set were subjected to progressively increasing pressure-impulse combinations to study component behaviour from elastic response up to inelastic component failure. The blast performance of companion as-built and retrofitted specimens was quantified in terms of measured load-deformation characteristics, and observed member behaviour throughout all stages of response. The results show that externally bonded FRP retrofits are an effective retrofit technique to improve the blast resistance of reinforced concrete structures, provided that debonding of the composite from the concrete substrate is prevented. The test results also indicate that FRP retrofitted reinforced concrete structures may survive initial inbound displacements, only to failure by moment reversals during the negative displacement phase. The experimental test data was used to verify analytical techniques to model the behaviour of reinforced concrete walls and slabs subjected to blast loading. The force-deformation characteristics of one-way wall strips were established using inelastic sectional and member analyses. The force-deformation characteristics of two-way slab plates were established using commonly accepted design approximations. The response of all specimens was computed by explicit solution of the single degree of freedom dynamic equation of motion. An equivalent static force procedure was used to analyze the response of CFRP retrofitted specimens which remained elastic after testing. The predicted maximum displacements and time-to-maximum displacements were compared against experimental results. The analysis indicates that the modelling procedures accurately describe the response characteristics of both retrofitted and unretrofitted specimens observed during the experiment.

Mitigation of the blast risk associated with terrorist attacks and accidental explosions threatening critical infrastructure has become a topic of great interest in the civil engineering community, both in Canada and abroad. One method of mitigating blast risk is to retrofit vulnerable structures to resist the impulsive effects of blast loading. A comprehensive re-search program has been undertaken to develop fibre reinforced polymer (FRP) retrofit methodologies for structural and non-structural elements, specifically reinforced concrete slabs and walls, subjected to blast loading. The results of this investigation are equally valid for flexure dominant reinforced concrete beams subject to blast effects. The objective of the research program was to generate a large volume of research data for the development of blast-resistant design guidelines for externally bonded FRP retrofit systems. A combined experimental and analytical investigation was performed to achieve the objectives of the program. The experimental program involved the construction and simulated blast testing of a total of thirteen reinforced concrete wall and slab specimens divided into five companion sets. These specimens were subjected to a total of sixty simulated explosions generated at the University of Ottawa Shock Tube Testing Facility. Companion sets were designed to study one- and two-way bending, as well as the performance of specimens with simply-supported and fully-fixed boundary conditions. The majority of the specimens were retrofitted with externally bonded carbon fibre reinforced polymer (CFRP) sheets to improve overall load-deformation characteristics. Specimens within each companion set were subjected to progressively increasing pressure-impulse combinations to study component behaviour from elastic response up to inelastic component failure. The blast performance of companion as-built and retrofitted specimens was quantified in terms of measured load-deformation characteristics, and observed member behaviour throughout all stages of response. The results show that externally bonded FRP retrofits are an effective retrofit technique to improve the blast resistance of reinforced concrete structures, provided that debonding of the composite from the concrete substrate is prevented. The test results also indicate that FRP retrofitted reinforced concrete structures may survive initial inbound displacements, only to failure by moment reversals during the negative displacement phase. The experimental test data was used to verify analytical techniques to model the behaviour of reinforced concrete walls and slabs subjected to blast loading. The force-deformation characteristics of one-way wall strips were established using inelastic sectional and member analyses. The force-deformation characteristics of two-way slab plates were established using commonly accepted design approximations. The response of all specimens was computed by explicit solution of the single degree of freedom dynamic equation of motion. An equivalent static force procedure was used to analyze the response of CFRP retrofitted specimens which remained elastic after testing. The predicted maximum displacements and time-to-maximum displacements were compared against experimental results. The analysis indicates that the modelling procedures accurately describe the response characteristics of both retrofitted and unretrofitted specimens observed during the experiment.

The performance of reinforced concrete (RC) columns during recent earthquakes has clearly demonstrated the possible failures associated with inadequate confining reinforcement. The confinement reinforcement requirements of older codes were less stringent than present standards. Many studies were conducted by applying different retrofitting techniques for RC columns that have inadequate confinement reinforcement. A new retrofitting technique by means of Carbon Fiber Reinforced Polymer (CFRP) was developed and tested in many countries in the last decade. This technique is performed by CFRP wrapping the critical region of columns. The effectiveness of CFRP retrofitting technique was shown in many studies conducted worldwide. In Turkey, the frame members are considerably deficient from the seismic detailing point of view. Therefore, in order to use the CFRP retrofitting technique effectively in Turkey, experimental evidence is needed. This study investigates the performance of CFRP retrofitted RC columns with deficient confining steel and low concrete strength. It was concluded by experimental and analytical results that the CFRP retrofitting method can be implemented to seismically deficient columns. Moreover, two design approaches were proposed for CFRP retrofit design of columns considering safe design regulations.

The application of carbon fiber reinforced polymers (CFRP) is one of the effective retrofitting and strengthening methods that is used worldwide and is starting to be used in Turkey as well because they have high strength and high modulus in the fiber direction, have very low coefficient of thermal expansion when compared to concrete and steel and are known not to corrode. Since FRPs are lightweight, their mass can be neglected when compared to concrete and steel. However, before proposing this material as an alternative for strengthening and retrofitting applications their long-term behavior should be understood because they are applied on to concrete by several layers of epoxy-based adhesives, which can be affected by change in humidity, temperature and load. Therefore, behavior of CFRP-strengthened structures in varying temperature and humidity conditions must be investigated. In this dissertation, behavior of CFRP confined cylindrical and prismatic concrete specimens having square cross-section were investigated under sustained compressive loads, dry and wet heating-cooling cycles, and outdoor exposures under direct sunlight, to determine the possible changes in their mechanical properties. Sustained loads were applied as the 40% and 50% of their confined axial load capacity. In addition to the sustained loads, specimens were subjected to 200 heating-cooling cycles between -10&deg / C to 50&deg / C. In order to understand the change in behavior of CFRP confined concrete specimens better, they were divided in six groups. A single effect was investigated in each group. After aging tests mechanical properties of the specimens were recorded via monotonic uniaxial loading. It was observed that temperature cycles had little effect on behavior but sustained loads changed the shape of the axial stress-strain diagram and resulted in a dramatic decrease in ultimate strain. Based on the test results and also using the data of similar studies available in the literature, strength and strain models considering the exposures as independent parameters were established and finally axial stress-strain curve was tried to be predicted.

A lightweight carbon fiber reinforced polymer (CFRP) sandwich panel has been developed for floor use in commercial office building construction. CFRP laminate skins were combined with low-density rigid polyurethane foam to create a composite sandwich panel suitable for floor use. The CFRP sandwich panel was optimized to withstand code prescribed office-building live loads using a 3D finite element computer program called SolidWorks. The thickness of the polyurethane foam was optimized to meet both strength and serviceability requirements for gravity loading. Deflection ultimately was the controlling factor in the design, as the stresses in the composite materials remained relatively low. The CFRP sandwich panel was then subjected to combined gravity and lateral loading, which included seismic loads from a fictitious 5-story office building located in a region of high seismic risk. The results showed that CFRP sandwich panels are a viable option for use with floors, possessing sufficient strength and stiffness for meeting code prescribed design loads, while providing significant benefits over traditional construction materials.