The aim of this thesis was to develop user interface in LabVIEW to make typical measurements with spectral analyzer HP89410A There is introduced the theory of operation of an analogue heterodyne and a digital FFT spectral analyzer. It is explained the background of the Fast Fourier Transform. There are discussed the key settings in measuring with FTT analyzer, like window function, bandwidth, number of frequency points, or the averaging. Further is described the program, which was developed for measuring frequency characteristic by white noise and by stepped measurement. It was also made a module for measuring Signal to Noise Ratio and module for Total Harmonic Distortion. In the last part of this thesis are shown the results of processed exemplar measurements.

This diploma work deals with active circuit elements and proposals of methods for measuring of some parameters of these elements. In the opening part the work deals with general classification of elements used in electronic circuits, ideal and real current sources and power supplies. Further there are stated basic parameters and characteristics presented by producers in a catalogue sheet for active elements MAX435, OPA660, AD844 and MAA741 element which already belongs to the history of IC. Main attention is paid to active circuit elements with current sources driven by CCCS (Current Controlled Current Source) and AD844 (high speed monolithic operational amplifier). In the work there is described a method for determining of selected parameters of active elements with CCCS. Examined parameters were frequency characteristics of current transfer, input impedance and output impedance. The proposed method was verified by a computer simulation on above mentioned active elements by means of PSpice software. Findings along with the description are summarized at the end of the work. In the closing part of the work there is undertaken a real measure of AD844 element based on the proposed method and the findings are compared with particular simulations. However, at first a flat connection board was made by means of EAGLE software and then the measure was performed on it.

The aim of this Master´s thesis is use of instrument transformers and sensors on field of industry protection. We will compare current and voltage transformers, current sensor – based on Rogowski coil, voltage sensor – based on voltage divider. By this measure devices, we can monitoring values of analog quantities in medium voltage switchgear. It is impossible to compare, measure and analyze without this measure devices. There is protection terminal REF542plus, which can compile this values. The REF542plus ability are measuring, monitoring, remote control and protection. First, we will discuss about theory of sensors and convential instrument transformers and analysis of analog signal. We will compare analog input channel on sensor´s analog module and transformer´s analog module. There are few differences between type of analog modules. For analog signal analysis are important frequency filters and Analog/ Digital Convertor (sigma-delta). We will describe functions and options of REF542plus. In practical part of this project, we will test protection functions of protection terminal. First, protection terminal will be connected to sensors. Second protection terminal will be connected to transformers. For testing we chose Earth-fault directional protection and differential protection. We will make only secondary tests. That´s mean, input analog quantities to REF542plus will be simulated by tester. In all we will verify quality of protection. We will focus on lower settings of protection and we will inject protection by low current. Objectives are testing of trip characteristics and measuring of trip time.

This work deals with the most famous constructions of planar antennas. The work analyses selected methods of connecting planar antennas' charging with the possibility of impedance adaptation. An important part of the work consists of description of techniques for increasing bandwidth and conversely techniques for reducing the dimensions which are important for the design of planar antennas for mobile devices. The antennas were designed by means of theoretical basis and their properties were examined in the electromagnetic field simulator. The selected antenna model was constructed and its parameters were measured experimentally. The matching circuit for the antenna to tune it to different resonant frequencies was designed and constructed.

Vývoj UHV kompatibilního kombinovaného systému AFM/SEM. Modifikace předchozího AFM mikroskopu pro podmínky spojené s tímto systémem. Výzkum transportu elektrického náboje v organických solárních článcích pomocí měření jejich volt-ampérových charakteristik a povrchového potenciálu. Příprava zlatých hrotů pro STM netoxickou cestou.

Hydrogen, as a form of storage for the excess energy from renewable sources, is a technically and economically viable option. However, the technology is not mature enough to compete with the other renewable energy possibilities. In this thesis, a study based on coupling two 330 kW wind-turbines with an NELP. 40 electrolyzer this connection should improve the utilization of wind power. In this thesis are two options of energy utilization. The energy produced by the wind-turbine is stored in the form, of hydrogen and is then delivered for consumption at variable power through a fuel cell, second option is use of produced hydrogen as alternative fuel for cars. This study is a general introduction for the wind energy system with hydrogen storage. Future studies should be more complex and detailed in order to understand and model the system with greater accuracy and to increase the possibility for the utilization of wind energy to generate hydrogen. This would enhance wind power competitiveness and sustain the continuously changing world energy demands.

ith one controlled extraction and one uncontrolled extraction, calculation of the flow channel at all stage, design and calculation of the regulation valve and create connection diagram of steam turbine and air cooled condenser. At the beginning of this work is an overview of manufacturers of steam turbines and their unified products. Master thesis was developer with G-Team, a.s. as using calculations and the instructions given in the recommended literature with supporting CFD simulations to determine the loss coefficients and FEA simulations to determine the eigenfrequencies blades.

The doctoral thesis deals with diagnostics of local defects in PN junctions and brings new information about microplasma noise behaviour and its usage for the temperature changes detection inside PN junctions. Defects in PN junctions are the source of microplasma noise. There were deviations observed in microplasma noise from the common known rectangle shape pulses during the measurements. These deviations were correlated with the temperature change directly in the defect area and in the defect area surroundings. Generation and recombination coefficients are commonly thought to be constant. However, these coefficients were observed to be not stable with time and this effect is explained in this work. The doctoral thesis then focuses on the PN junction parameters determination in the case when it is not possible to define unambiguously whether it is abrupt or linearly graded PN junction. The most significant parameters which are to be determined are barrier capacity, diffusion voltage and depleted area width in dependence on the voltage. The correlation between local avalanche discharge in PN junction and negative differential resistance appearance on VA characteristics of reverse-biased diode was qualitatively verified. The last important point in the work is computer modelling of temperature behaviour in the defect area and its surroundings during local avalanche breakdown. Thus the method of real diodes heating area parameters determination was introduced.

The task of the thesis was studding of tantalum capacitors with solid electrolytes properties. Ta – Ta2O5 – MnO2 capacitor by its construction represents MIS structure, where tantalum anode has metal conductivity and MnO2 cathode is semiconductor. Isolation layer consists of tantalum pentoxide Ta2O5 with relative permitivity r = 27. Dielectric thickness is typically in range from 30 to 150nm. The capacitor charge is not only stored and accumulated on electrodes but also in localised states (oxide vacancies) in isolation layer. The capacitor connected in normal mode represents MIS structure polarized in reveres direction when the applied voltage higher potential barrier between semiconductor - MnO2 cathode and isolation of Ta2O5. The transport of charge carriers via isolation layer is determined by Poole-Frenkel mechanisms and tunnelling. Poole-Frenkel mechanism of charge transport is dominant in low intensity of electric field. Tunnelling determines current at higher electric field intensity. During low intensity of electric field ohmic component is also presented which is determined by volume of resistance of impurities in isolation layer due to donor states of oxygen vacancies. Based on the modelling of measured VA characteristics is possible to estimate determine dielectric thickness of Ta2O5 and determine share of Poole-Frenkelov and tunnel current and charge transportation. The thesis is described charge transport and charge concentration on tantalum capacitor in low frequency area and analysis of capacitor behaviour at frequency band. The first impulse for the thesis was an effort to create equivalent circuit diagram of tantalum capacitor in respect of its physical and electrical behaviour. There is an opportunity to study and determine electric charge transport and its accumulation based on the equivalent circuit diagram structure. There is also a chance to define and trace potential barriers and charge distribution in the capacitor structure based on an measurement and carried out experiments. This methodology and analysis consists of electrical characteristic determination to create physical model of the capacitor describing it function, properties and behaviour.

The main objective of the presented thesis is to contribute to the development of diagnostic methods for piezoelectric sensor testing. The thesis describes the methods for piezoelectric sensors microcracks identification and diagnostics. The core of the thesis presents the development of a knock sensor prototype, design of suitable methods for the knock sensors diagnosis and evaluation of developed methods with focus on detection of microcracks in the sensor piezoceramic. The last part of the thesis deals with the influence of cracks and splits on the measured data from the piezoelectric transducer. The presented methods are focusing on impedance measurements and sensors frequency response measurements. Known properties of used piezoelectric material as an information source for measurement and diagnosis are provided. The main result of the work is the evaluation of the methods developed for the piezoelectric sensors self-diagnosis.