Additive manufacturing (AM) is a promising manufacturing process that provides that ability to fabricate components with complex geometries with relatively low lead times compared to other manufacturing processes. This allows for more freedom of design, as prototypes can easily be produced throughout the development process. AM is also especially beneficial in tooling applications, where internal geometries such as cooling channels are required in order to improve the quality of the manufactured parts. These geometries are more difficult to produce with more conventional manufacturing methods such as forging or casting. Currently, Laser Powder Bed Fusion (LPBF) shows the most promise in the field of Additive Manufacturing (AM) of metals, as it offers the freedom to produce complex components with little post processing required. Additionally, post processing with Hot Isostatic Pressing (HIP) can be implemented to significantly enhance the final properties of the material.  The LPBF-process can produce many different defects within the parts such as: part porosity and lack of fusion. This is mainly due to the layer-by-layer configuration of the process. Parts can also experience large thermal fluctuations and rapid cooling rates which can generate large residual stresses. This can result in significant cracking in certain high alloyed materials which can impact part quality and  material properties. If the cracking is severe enough, it will result in failure of the entire component and render the entire parts completely useless. Post processing with HIP may remove some of these defects and reduce the residual stresses in the material and thus produce a material with properties that are satisfactory. The purpose of this thesis is to investigate the processability of a high alloy cold work tool steel with LPBF. The main focus is the influence of the processing parameters and part geometry on the quality of the produced parts. Furthermore, the influence of the processing parameters on defects and microstructure will also be investigated. The aim is to produce parts that can be enhanced with HIP as a post processing treatment. Additionally, the impact of HIP on the properties of the part will also be investigated in order to determine if the there are any improvements in terms ofreduction in part defects and the removal of any undesired microstructural features which are produced from the process. The experimental results showed that the processability of the tool steel is difficult. Several sample volumes were produced with varying processing parameters and scanning strategies, and all the specimens from all sample volumes exhibited some cracking. Parts produced with a combination of contouring and hatching strategy, where there is an internal structure showed the most promise, as these parts exhibited the least amount of severe cracking. However, additional research of the processing parameters and scanning strategies is required in order to reduce the amount of cracking of the external shell structure and thus, achieve proper densification of the parts when post processing with HIP. / Additiv tillverkning (AM) är en lovande tillverkningsprocess som ger möjligheten att tillverka komponenter med komplexa geometrier med relativt låga ledtider jämfört med andra tillverkningsprocesser. Detta ger större frihet i under designprocessen eftersom prototyper enkelt kan produceras under hela utvecklingsprocessen. AM är också särskilt fördelaktigt i verktygstillämpningar, där interna geometrier såsom kylkanaler krävs för att förbättra kvaliteten på de tillverkade delarna. Dessa geometrier är svårare att tillverka med mer konventionella tillverkningsmetoder som smidning eller gjutning. För närvarande visar det sig att Laser Powder Bed Fusion (LPBF) är det mest lovande inom området additiv tillverkning av metaller, eftersom processen erbjuder friheten att producera komplexa komponenter samt att efterbearbetning som krävs blir mindre. Dessutom kan efterbearbetning med Hot Isostatic Pressing (HIP) implementeras för att avsevärt förbättra materialets slutliga egenskaper. LPBF-processen kan ge upphov till många olika defekter i delarna såsom: delporositet och lack of fusion. Detta beror främst på att processen sker lagervis vilket kan ge upphov att många småfel. Delar kan också uppleva stora termiska fluktuationer och snabba kylningshastigheter som kan generera stora restspänningar. Det kan resultera i stor sprickbildning i vissa höglegerade material vilket kan påverka delarnas kvalitet och materialegenskaper. Om sprickorna som bildas är stora eller djupa nog kommer detta att resultera i att hela komponenten blir oanvändbar. Efterbearbetning med HIP kan ta bort en del av dessa defekter och minska restspänningarna i materialet och därmed producera ett material med goda egenskaper. Syftet med detta arbete är att undersöka bearbetbarheten hos ett höglegerat kallbearbetningsstål med som produceras med LPBF. Huvudfokus är påverkan av processparametrar och detaljgeometrin på kvaliteten på de producerade delarna. Vidare kommer också processparametrarnas inverkan på defekter och mikrostruktur att undersökas. Syftet är att producera delar som kan förbättras med HIP som efterbehandlingsbehandling. Dessutom kommer effekterna av HIP på delens egenskaper också att undersökas för att avgöra om det finns några förbättringar i termer av minskning av deldefekter och avlägsnande av alla oönskade mikrostrukturella egenskaper som produceras från processen. De experimentella resultaten visade att verktygsstålets bearbetbarhet är svår. Flera provvolymer producerades med varierande processparametrar och skanningsstrategier, och alla prover från alla provvolymer uppvisade viss sprickbildning. Delar som tillverkats med en kombination av kontur och hatch, där det finns en inre struktur visade sig mest lovande, eftersom dessa delar uppvisade minst sprickbildning. Ytterligare arbete av processparametrarna och skanningsstrategier krävs dock för att minska mängden sprickbildning i den yttre skalstrukturen och därmed uppnå korrekt förtätning av delarna vid efterbearbetning med HIP.

The demand for Advanced High Strength Steel (AHSS) in the automotive industry is increasing day by day. It is mainly motivated by the fact that AHSS can be used as thin sheets while having high strengths. It enables weight reduction of the automobiles which consequently increases the fuel efficiency and has proven to be less harmful to the environment. It is also expected that AHSS will have even higher strength in the near future. Cold work tools steels with 5 wt.% Cr are commonly used to process AHSS. Therefore, the tool steel must meet the challenges in the future, i.e. have even higher hardness, compressive strength and toughness. One way of increasing the mechanical properties of the tool steel is by improving the heat treatment parameters. However, it is not possible without a deeper understanding of the heat treatment process. Therefore, this work presents investigations related to phase transformations occurring in a 5 wt.% Cr cold work tool steel during heat treatment. Furthermore, the influence of austenitisation and tempering temperatures on the microstructure and mechanical properties were investigated. The studies revealed that a higher austenitisation temperature can be used to achieve a higher hardness, good compressive strength and adequate toughnessof the steel. However, too high austenitisation temperature may result inexcessive coarsening of prior austenite grains which reduced the impact toughness. It was also found that retained austenite can transform during tempering by two different mechanisms. Firstly, when tempering at 525°C, carbides precipitate in retained austenite lowering its stability and permitting a transformation to marten site on cooling. Secondly, when tempering at 600°Cfor extended holding time retained austenite isothermally transforms to ferrite and carbides. This occurs by precipitation of carbides in retained austenite followed by a final transformation to ferrite and carbides.These results were used to understand the standard tempering procedure of the 5 wt.% Cr cold work tool steel. Furthermore, alternative heat treatment procedures are discussed based on the important findings presented in this thesis.