L'efficacité des cellules photovoltaïques organiques est influencée par la morphologie du mélange composant la couche active. L'objectif de cette thèse a été d'élaborer un agent compatibilisant pour stabiliser la morphologie du mélange P3HT:PCBM. Nous avons choisi de synthétiser des copolymères alternant motifs C60 et polythiophène pour améliorer la miscibilité entre P3HT et PCBM. Les copolymères ont été réalisés par polycondensation d'un dérivé C60 avec plusieurs oligothiophènes régioréguliers de difonctionnalité contrôlée. Une attention particulière a été accordée aux conditions de polycondensation qui ont été optimisées pour favoriser de hauts degrés de polymérisation. Les caractérisations structurales, optiques et électrochimiques des matériaux ont été réalisées. Leur effet compatibilisant a été évalué en caractérisant la morphologie de la couche active par des mesures en cellules photovoltaïques, des observations par microscopie à force atomique et des calculs d'énergies de surface. / Efficiency of organic photovoltaic solar cells is influenced by the active layer's morphology. The aim of this thesis was to elaborate a compatibilising agent which could stabilise the morphology of the P3HT:PCBM blend. We chose to synthesize alternating copolymers based on fullerene and polythiophene blocks to improve compatibility between P3HT and PCBM. The synthesis of copolymers has been achieved by polycondensation of a fullerene derivative with several regioregular oligothiophenes for which difunctionality was well controlled. Particular care has been given to the optimisation of polycondensation conditions in order to favour high polymerisation degrees. Structural, optical and electrochemical characterisations have been realized. The compatibilising effect of our copolymers on the active layer morphology has been investigated on the basis of photovoltaic measurements, atomic force microscopy observations and surface energy calculations.

Le mélange de polymères est une méthode répandue pour élaborer des matériaux polymères. Cependant, la plupart des polymères sont thermodynamiquement immiscibles entre eux, engendrant une séparation de phase des mélanges et une détérioration de leurs propriétés. Afin de palier ces problèmes, la méthode dite compatibilisation réactive est souvent employée. Elle est basée sur la formation in-situ de copolymères à bloc ou greffés par l’intermédiaire de réactions interfaciales entre polymères réactifs. Cette thèse a pour objet de développer un concept dit agent compatibilisant-traceur réactif qui permettra d’utiliser de faibles quantités d’agents compatibilisants réactifs pour évaluer leurs efficacités de compatibilisation directement sur des extrudeuses bi-vis industrielles, d’une part ; et de caractériser la performance du mélange d’une extrudeuse bi-vis en fonction des conditions opératoires et/ou du profil de vis employé. Ses principales contributions se résument ci-après. L’anthracène de 9-méthylaminométhyle (MAMA), une molécule fluorescente, est incorporée dans un copolymère statistique de styrène (St) et d’isocyanate de 3-isopropenyle-?, ?’-diméthylebenzène (TMI), noté PS-TMI, pour former un agent compatibilisant-traceur réactif, noté PS-TMI-MAMA. Ce dernier sert à la fois comme agent compatibilisant réactif grâce aux groupements isocyanate et traceur grâce aux groupements fluorescents. Il est utilisé pour les mélanges à base de polystyrène (PS) et de polyamide 6 (PA6) afin d’évaluer son efficacité de compatibilisation. Les mélanges PS/PA6 sont élaborés dans un mélangeur discontinu et une extrudeuse bi-vis, respectivement. Dans le cas du mélangeur discontinu, la quantité du copolymère greffé formé in-situ, noté PS-g-PA6-MAMA, augmente alors que le diamètre des domaines de la phase dispersée (DDD) diminue considérablement au début du mélange. Lorsque le mélange se poursuit, le nombre de greffons en PA6 du PS-g-PA6-MAMA augmente, engendrant une composition très asymétrique du PS-g-PA6-MAMA qui est thermodynamiquement instable aux interfaces. De ce fait, il peut être arraché des interfaces vers la phase PA6 et peut y former des micelles. Lorsqu’il est arraché des interfaces, il perdra son efficacité de compatibilisation et le DDD augmentera. L’action du mélange a un double effet sur le procédé de compatibilisation réactive. Il promeut la réaction interfaciale entre le PS-TMI-MAMA et le PA6, d’une part ; et aggrave l’arrachage du PS-g-PA6-MAMA de l’interface, d’autre part. L’utilisation de faibles quantités de l’agent compatibilisant-traceur réactif permet de mesurer les évolutions de la teneur en agent compatibilisant-traceur réactif, du DDD et de la teneur en agent compatibilisant-traceur réactif ayant réagi en fonction du temps de séjour dans une extrudeuse bi-vis. Pour une masse molaire donnée, l’efficacité de compatibilisation d’un agent compatibilisant-traceur réactif augmente avec l’augmentation de la teneur en TMI dans une certaine limite. Pour une teneur en TMI donnée, la réaction interfaciale est plus rapide avec la diminution de la masse molaire dans une certaine limite et le DDD devient plus petit en un temps plus court. L’influence du taux de remplissage de la vis est plus significative que celle du temps de séjour. Lorsque le taux de remplissage de la vis augmente, le taux de la réaction interfaciale augmente et le DDD diminue. Lorsque l’angle d’un élément de mélange augmente, les efficacités du mélange distributif et du mélange dispersif augmentent, ce qui se traduit par une augmentation de la quantité du PS-g-PA6-MAMA formée et une diminution du DDD par rapport à la même quantité de PS-g-PA6-MAMA produite. Lorsque la largeur d’un élément de mélange augmente, l’efficacité du mélange distributive augmente alors que celle du mélange dispersif demeure inchangée. La substitution d’éléments de mélange par des éléments inverses améliore l’efficacité du mélange distributif et celle du mélange dispersif / Polymer blending is a common method to prepare high-performance polymer materials. However, most polymer pairs are thermodynamically immiscible, leading to phase separation and deterioration in material properties. To overcome such problems, the most common method is reactive compatibilization which is based on the in-situ formation of a graft or block copolymer by interfacial reaction between reactive polymers. This thesis aims at developing a concept of reactive compatibilizer-tracer which will allow using small amounts of reactive compatibilizers to evaluate their compatibilizing efficiency in industrial scale twin screw extruders, on the one hand; and to characterize the mixing performance of a twin screw extruder as a function of process conditions and/or screw profile. Its main contributions are summarized below. 9-(methylaminomethyl) anthracene (MAMA), a fluorescent molecule, is incorporated into a random copolymer of styrene (St) and 3-isopropenyl-?, ?’-dimethylbenzene isocyanate (TMI), denoted as PS-TMI, to form a reactive compatibilizer-tracer, denoted as PS- TMI-MAMA. The latter serves both as a reactive compatibilizer due to its isocyanate moieties and a tracer due to its fluorescent moieites. It is used for polystyrene (PS)/polyamide 6 (PA6) blends to evaluate its compatibilizing efficiency. Compatibilized PS/PA6 blends are processed in a batch mixer and in a twin screw extruder, respectively. In the case of the batch mixer, the amount of the in-situ formed graft copolymer denoted as PS-g-PA6-MAMA increases and the dispersed phase domain diameter (DDD) decreases drastically in the initial period of mixing. As the mixing further proceeds, the number of PA6 grafts of the PS-g-PA6-MAMA increases, resulting in a highly asymmetrical composition of the PS-g-PA6-MAMA which causes thermodynamic instablility at the interface. As a result, it could be pulled out of the interface to the PA6 phase and form micelles. Once it is pulled out of the interface, it will lose its compatibilizing efficiency and the dispersed phase domain diameter increases sharply. Mixing has a dual effect on the reactive compatibilization process. On the one hand, it promotes the interfacial reaction between the PS-TMI-MAMA and PA6. On the other hand, it aggravates the pull out of the resulting PS-g-PA6-MAMA from the interface. The use of small amounts of the reactive compatibilizer-tracer together with transient experiments for RTD allows assessing the evolutions of the reactive compatibilizer-tracer content (CC), the dispersed phase domain diameter (DDD), and the reacted reactive compatibilizer-tracer content (RCC) as a function of residence time in a twin-screw extruder. Based on the above results, the emulsification curve (DDD vs. CC), the RCC vs. CC curve and effective emulsification curve (DDD vs. RCC) are obtained. When the molar mass of the reactive compatibilizer-tracer is fixed, its compatibilizing efficiency increases with increasing TMI content within an appropriate range. When its TMI content is fixed, the interfacial reaction goes faster as the molar mass of the reactive compatibilizer-tracer decreases within a certain range, and the DDD becomes smaller in a shorter time. The effect of degree of fill fixed by the throughput Q/screw speed N ratio is more dominant than that of residence time. As the degree of fill increases, the interfacial reaction increases and the DDD decreases. As the angle of adjacent the kneading block increases, its distributive and dispersive mixing efficiencies increase, resulting in an increase in interfacial area generation and a decrease in DDD on the basis of the same amount of PS-g-PA6-MAMA. On the other hand, as the width of the kneading block increases, the distributive mixing efficiency increases and the dispersive mixing efficiency remains unchanged. Substitution of kneading blocks by reverse ones increase both the distributive and dispersive mixing efficiencies

O crescimento na geração de rejeitos de equipamentos elétricos e eletrônicos (REEE), legislações mais rigorosas e o valor agregado destes materiais incentivam o desenvolvimento de tecnologias de reciclagem. Contudo, a reciclagem dos componentes poliméricos dos REEE (CP-REEE) precisa superar desafios como a degradação durante o uso e reprocessamento, a presença de diferentes aditivos nos rejeitos e a depreciação de propriedades causada pela mistura não controlada de polímeros. Assim, o objetivo deste trabalho foi desenvolver um estudo sobre a reciclagem mecânica na forma de blendas poliméricas de rejeitos do copolímero acrilonitrila-butadieno-estireno (ABS) e do poliestireno de alto impacto (HIPS), empregando agentes compatibilizantes. No desenvolvimento do trabalho foram realizadas a caracterização dos CP-REEE, análise das propriedades mecânicas, químicas, térmicas e morfológicas dos polímeros e das blendas de ABS/HIPS nas proporções de 1:3, 1:1 e 3:1 com variações na composição dos polímeros reciclados e virgens e por fim, realizado um estudo do envelhecimento foto-oxidativo acelerado de uma blenda ABS/HIPS. Os resultados mostraram que os polímeros ABS e HIPS reciclados ainda apresentam boas propriedades mecânicas e que a presença de agentes compatibilizantes provoca o aumento da tenacidade nas blendas ABS/HIPS. A incorporação de polímeros virgens nos materiais reciclados não promove ganho significativo nas propriedades mecânicas das blendas. Blendas com até 50% de ABS demonstraram ter propriedades próximas às do HIPS, enquanto as blendas com altos teores de ABS não alcançaram valores de propriedades mecânicas similares aos do ABS virgem. O comportamento das propriedades das blendas virgens e recicladas frente ao envelhecimento fotoquímico foi similar, indicando que o material reciclado apresenta grande potencial para aplicações. O estudo de blendas ABS/HIPS de CP-REEE demonstra que o controle da composição das blendas definem a sua aplicação. / The growth in waste electrical and electronic equipment (WEEE) generation, directives more stringent and the aggregate value presents in these waste are encouraging the development of recycling technologies. However, recycling of polymeric components from WEEE (PC-WEEE) must overcome challenges such as degradation during use and reprocessing, the presence of various additives in the waste and the depreciation of properties caused by uncontrolled polymers mixture. The aim of this work was to develop a study of the mechanical recycling in the form blends with of polymeric waste of acrylonitrile-butadiene-styrene copolymer blends (ABS) and high impact polystyrene (HIPS) using compatibilizers. During the study was carried out the characterization of the PCWEEE and mechanical, chemical, thermal and morphological analysis of the polymers and the ABS / HIPS blends in proportions of 1:3, 1:1 and 3:1 with recycled and virgin polymers, as well as a study of the accelerated photo-oxidative aging of the ABS/HIPS blends. The results showed that ABS and HIPS recycled polymers still have good mechanical properties and the presence of compatibilization agents leads to increased toughness in ABS/HIPS blends. The incorporation of virgin polymers in recycled materials does not promote significant gain in the mechanical properties of the blends. Blends with up to 50% ABS have demonstrated to be closer to the HIPS, while blends with high content of ABS did not reach values of mechanical properties similar to the virgin ABS. The mechanical properties of virgin and recycled blends during the photochemical aging were similar, indicating that the recycled material has great potential for applications. The study of ABS/HIPS blends from PC-WEEE demonstrated that control of the blend composition establish their applications.

Made available in DSpace on 2016-12-08T17:19:26Z (GMT). No. of bitstreams: 1 Marindia Decol.pdf: 3575085 bytes, checksum: bed6c0ed662d3c76c64b6cfdac902d8b (MD5) Previous issue date: 2015-07-15 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Poly (lactic acid) (PLA) is a rigid and brittle thermoplastic polymer, and poly (ε-caprolactone) (PCL) is a thermoplastic polymer of lower rigidity and higher toughness than PLA. Combination of these properties through the blend PLA/PCL has been studied successfully to change the final properties of the PLA. The addition of multiwalled carbon nanotubes (MWCNT) in the blend PLA/PCL may induce peculiar orphologies depending on their location, resulting in the getting new properties or modifying the properties of the PLA matrix. This study aimed to evaluate the effect of adding the PCL, the compatibilizer Cesa-mix and MWCNT the final properties of the PLA. Mixtures were prepared in internal mixer chamber coupled to a torque rheometer and subjected to characterizations of morphological, thermal, mechanical and electrical properties. In the morphological analysis, there was a 37% reduction in the average size of the phases of the PCL blends PLA/PCL with the addition of compatibilizer Cesa®- mix, a heterogeneous distribution of MWCNT the PLA matrix and a selective location of MWCNT in phase PCL. With respect to thermal properties, the addition of the compatibilizing PCL and did not significantly affect the thermal degradation onset temperature (Tonset) of the PLA, but the addition of the MWCNT in PLA resulted in decreased Tonset nanocomposites. The melting temperature did not change significantly with the addition of PCL, the compatibilizer and MWCNT on the PLA matrix. Already cold crystallization temperature decreased and the degree of crystallinity of the PLA increased with the addition of PCL blends and MWCNT in nanocomposites. Decreases of 35% on elastic hardness and 29% in modulus of elasticity was observed with the addition of PCL and compatibilizer Cesa®-mix in the blends PLA/ PCL/AC/2,5%. With the addition of MWCNT was observed an increase of 6,8% on elastic hardness and 8% in the modulus of elasticity of PLA/CNT mixtures with 1,0% w/w. Blends of PLA/PCL with 0,5% and 1,0% w/w CNT with and without compatibilizer, had a decrease in modulus of elasticity and elastic hardness. No significant changes were observed in the electric resistance of the samples with the addition of the compatibilizer, the PCL and MWCNT with 0,5% and 1,0% w/w. Selective location of MWCNT the PCL phase had great influence on morphological, thermal, mechanical and electrical properties of nanocomposites. / O poli(ácido lático) (PLA) é um polímero termoplástico rígido e frágil, e a poli(ε-caprolactona) (PCL) é um polímero termoplástico de menor rigidez e maior tenacidade que o PLA. A combinação destas propriedades através da blenda PLA/PCL tem sido estudada com êxito no auxílio à alteração das propriedades finais do PLA. A adição de nanotubos de carbono de paredes múltiplas (NTCPM) na blenda PLA/PCL pode induzir a morfologias peculiares dependendo da sua localização, resultando na obtenção de novas propriedades ou na alteração das propriedades da matriz PLA. Este trabalho teve como objetivo avaliar o efeito da adição do PCL, do compatibilizante Cesa-mix e dos NTCPM nas propriedades finais do PLA. As misturas foram preparadas em misturador de câmara interna acoplado a reômetro de torque e submetidas à caraterizações das propriedades morfológicas, térmicas, mecânicas e elétricas. Na análise morfológica, observou-se uma redução de 37% no tamanho médio das fases de PCL nas blendas PLA/PCL com a adição do compatibilizante Cesa®- mix, uma distribuição heterogênea dos NTCPM na matriz PLA e uma localização seletiva dos NTCPM na fase PCL. Em relação às propriedades térmicas, a adição do PCL e do compatibilizante não afetaram significativamente na temperatura de início de degradação térmica (Tonset) do PLA, porém a adição de NTCPM no PLA resultou em decréscimo na Tonset dos nanocompósitos. A temperatura de fusão não apresentou variação significativa com a adição do PCL, do compatibilizante e dos NTCPM na matriz PLA. Já a temperatura de cristalização a frio diminuiu e o grau de cristalinidade do PLA aumentou com a adição de PCL nas blendas e dos NTCPM nos nanocompósitos. Diminuições de 35% na dureza elástica e de 29% no módulo de elasticidade foram observadas com a adição do PCL e do compatibilizante Cesa®-mix nas blendas PLA/PCL/AC 2,5%. Com a adição de NTCPM foi observado um aumento de 6,8% na dureza elástica e de 8% no módulo de elasticidade das misturas PLA/NTC com 1,0% m/m. As misturas de PLA/PCL com 0,5% e 1,0% m/m de NTC com e sem compatibilizante, tiveram um decréscimo no módulo de elasticidade e na dureza elástica. Não foram verificadas alterações significativas na resistência elétrica das amostras com a adição do compatibilizante, do PCL e dos NTCPM com 0,5% e 1,0% m/m. A localização seletiva dos NTCPM na fase PCL teve grande influência nas propriedades morfológicas, térmicas, mecânicas e elétricas dos nanocompósitos.

O crescimento na geração de rejeitos de equipamentos elétricos e eletrônicos (REEE), legislações mais rigorosas e o valor agregado destes materiais incentivam o desenvolvimento de tecnologias de reciclagem. Contudo, a reciclagem dos componentes poliméricos dos REEE (CP-REEE) precisa superar desafios como a degradação durante o uso e reprocessamento, a presença de diferentes aditivos nos rejeitos e a depreciação de propriedades causada pela mistura não controlada de polímeros. Assim, o objetivo deste trabalho foi desenvolver um estudo sobre a reciclagem mecânica na forma de blendas poliméricas de rejeitos do copolímero acrilonitrila-butadieno-estireno (ABS) e do poliestireno de alto impacto (HIPS), empregando agentes compatibilizantes. No desenvolvimento do trabalho foram realizadas a caracterização dos CP-REEE, análise das propriedades mecânicas, químicas, térmicas e morfológicas dos polímeros e das blendas de ABS/HIPS nas proporções de 1:3, 1:1 e 3:1 com variações na composição dos polímeros reciclados e virgens e por fim, realizado um estudo do envelhecimento foto-oxidativo acelerado de uma blenda ABS/HIPS. Os resultados mostraram que os polímeros ABS e HIPS reciclados ainda apresentam boas propriedades mecânicas e que a presença de agentes compatibilizantes provoca o aumento da tenacidade nas blendas ABS/HIPS. A incorporação de polímeros virgens nos materiais reciclados não promove ganho significativo nas propriedades mecânicas das blendas. Blendas com até 50% de ABS demonstraram ter propriedades próximas às do HIPS, enquanto as blendas com altos teores de ABS não alcançaram valores de propriedades mecânicas similares aos do ABS virgem. O comportamento das propriedades das blendas virgens e recicladas frente ao envelhecimento fotoquímico foi similar, indicando que o material reciclado apresenta grande potencial para aplicações. O estudo de blendas ABS/HIPS de CP-REEE demonstra que o controle da composição das blendas definem a sua aplicação. / The growth in waste electrical and electronic equipment (WEEE) generation, directives more stringent and the aggregate value presents in these waste are encouraging the development of recycling technologies. However, recycling of polymeric components from WEEE (PC-WEEE) must overcome challenges such as degradation during use and reprocessing, the presence of various additives in the waste and the depreciation of properties caused by uncontrolled polymers mixture. The aim of this work was to develop a study of the mechanical recycling in the form blends with of polymeric waste of acrylonitrile-butadiene-styrene copolymer blends (ABS) and high impact polystyrene (HIPS) using compatibilizers. During the study was carried out the characterization of the PCWEEE and mechanical, chemical, thermal and morphological analysis of the polymers and the ABS / HIPS blends in proportions of 1:3, 1:1 and 3:1 with recycled and virgin polymers, as well as a study of the accelerated photo-oxidative aging of the ABS/HIPS blends. The results showed that ABS and HIPS recycled polymers still have good mechanical properties and the presence of compatibilization agents leads to increased toughness in ABS/HIPS blends. The incorporation of virgin polymers in recycled materials does not promote significant gain in the mechanical properties of the blends. Blends with up to 50% ABS have demonstrated to be closer to the HIPS, while blends with high content of ABS did not reach values of mechanical properties similar to the virgin ABS. The mechanical properties of virgin and recycled blends during the photochemical aging were similar, indicating that the recycled material has great potential for applications. The study of ABS/HIPS blends from PC-WEEE demonstrated that control of the blend composition establish their applications.

L’optimisation de la morphologie de la couche active est primordiale pour l’augmentation des rendements des cellules solaires photovoltaïques organiques. Nous avons montré l’influence du ratio de matériaux donneur (P3HT) et accepteur (PCBM) d’électrons ainsi que de la masse molaire du P3HT sur la morphologie de la couche active. Afin de contrôler la séparation de phases entre les matériaux donneur et accepteur d’électrons, il est possible d’utiliser des copolymères à blocs afin d’aider la compatibilisation entre le P3HT et le PCBM. Nous avons choisi de synthétiser des copolymères à blocs P3HT-b-polystyrène et des P3HT-b-polyisoprène présentant une certaine compatibilité avec les matériaux de la partie active. L’ajout optimisé de P3HT-b-polyisoprène permet une augmentation de 30% des rendements et de 90% de durée de vie des cellules solaires. / Active layer morphology optimization is fundamental to achieve high efficiency in organic photovoltaic solar cells. We showed the influence of the donor (P3HT) and acceptor (PCBM) material ratio and the impact of the P3HT molecular weight on the active layer morphology. We demonstrated the possibility of using well-designed block copolymers to help P3HT and PCBM compatibilization and to control their phase separation. We chose to synthesize P3HT-b-polystyrene and P3HT-b-polyisoprene for which each block is compatible with the active materials. Optimal addition of P3HT-b-polyisoprene enables to get a 30%-improved efficiency and a 90%-enhanced lifetime of the solar cells.