Magister Scientiae Dentium - MSc(Dent) / The treatment objectives in the restoration of an endodontically treated tooth are maximum retention of post and core and to create a design in which the tooth is preserved when the restoration fails. The ferrule effect in root treated teeth requiring cast post and core has been studied extensively and has been shown to greatly improve fracture resistance (Gluskin et al 1995, Libman & Nicholls, 1995. Hemmings et al, 1991. Barkhordar et al, 1989. Rosen & Partida-Rivera, 1986). Studies have also shown that in the case of cast post and core, the longer the ferrule, the greater the fracture resistance (Libman and Nicholls, 1995). The use of the new bonding agents, composite resin cements and core materials, have led to a more conservative approach to post and core restorations. However few studies have considered the effect of different ferrule designs on prefabricated post and composite core systems (Volwiler et al 1989, Al Hazaimeh and Gutteridge 2001). There is little information as to whether the ferrule is of additional value in providing reinforcement in these restorations. This study investigated the effects of different ferrule designs on the fracture resistance of teeth incorporating prefabricated posts and composite cores. In addition teeth restored with a composite core but with no prefabricated post were included in the study to assess the necessity of a post in the restoration of endodonticallytreated teeth. Sixty extracted maxillary incisors (centrals and laterals) and carunes were randomly assigned into three groups and restored. Two groups had a prefabricated post and composite core with varying ferrule designs. A third group had a core with composite packed into the root canal but no post. All teeth were restored with cast crowns to simulate the clinical situation. A Zwick universal testing machine was used to apply compressive loads progressively on the restored teeth until failure occurred as a result of either root, tooth or post fracture. Failure loads, modes of fracture, post and core systems and tooth preparation were recorded and statistically analysed. The results showed no significant difference in the amount of force needed to break the teeth in the different groups irrespective of whether the teeth had a ferrule or not. They also showed no significant difference in the amount of force needed to break the teeth in the different groups irrespective of whether the teeth had a post or not.

abstract: The future grid will face challenges to meet an increased power demand by the consumers. Various solutions were studied to address this issue. One alternative to realize increased power flow in the grid is to use High Temperature Low Sag (HTLS) since it fulfills essential criteria of less sag and good material performance with temperature. HTLS conductors like Aluminum Conductor Composite Reinforced (ACCR) and Aluminum Conductor Carbon Composite (ACCC) are expected to face high operating temperatures of 150-200 degree Celsius in order to achieve the desired increased power flow. Therefore, it is imperative to characterize the material performance of these conductors with temperature. The work presented in this thesis addresses the characterization of carbon composite core based and metal matrix core based HTLS conductors. The thesis focuses on the study of variation of tensile strength of the carbon composite core with temperature and the level of temperature rise of the HTLS conductors due to fault currents cleared by backup protection. In this thesis, Dynamic Mechanical Analysis (DMA) was used to quantify the loss in storage modulus of carbon composite cores with temperature. It has been previously shown in literature that storage modulus is correlated to the tensile strength of the composite. Current temperature relationships of HTLS conductors were determined using the IEEE 738-2006 standard. Temperature rise of these conductors due to fault currents were also simulated. All simulations were performed using Microsoft Visual C++ suite. Tensile testing of metal matrix core was also performed. Results of DMA on carbon composite cores show that the storage modulus, hence tensile strength, decreases rapidly in the temperature range of intended use. DMA on composite cores subjected to heat treatment were conducted to investigate any changes in the variation of storage modulus curves. The experiments also indicates that carbon composites cores subjected to temperatures at or above 250 degree Celsius can cause permanent loss of mechanical properties including tensile strength. The fault current temperature analysis of carbon composite based conductors reveal that fault currents eventually cleared by backup protection in the event of primary protection failure can cause damage to fiber matrix interface. / Dissertation/Thesis / Fault current temperature relationship program in C / Current temperature relationship program in C / M.S. Electrical Engineering 2014