Durant les dernières décennies, de plus en plus de types de cellules se sont révélées capables de sonder leur environnement mécanique par l'application de forces. Ce phénomène appelé «Mecanosensing» est lié à l'adhésion et la mécanique cellulaire, et est souvent étudié grâce à l'interaction des cellules avec des substrats artificiels. Dans des études distinctes, des surfaces chimiquement structurées avec une répartition des ligands spécifiques ont montré une forte influence sur l’adhésion et la mécanique cellulaire. Cependant, la relation entre les deux phénomènes n'a pas été beaucoup explorée, en partie parce que la fonctionnalisation de substrats mous s’est révélée être un défi technique.Pour résoudre ce problème, nous avons développé une technique simple et rentable nommée «reverse contact printing», afin de fabriquer des plots de protéines sub-microniques sur un élastomère d'élasticité contrôlée, le polydiméthylsiloxane (PDMS). Mon travail de thèse a focalisé sur la standardisation et la compréhension du procédé de transfert. A l’aide de mesures de forces réalisées par AFM nous avons mesuré l’élasticité du PDMS, ainsi que les forces de cohésion et d'adhésion effectives impliquées dans le processus. Nous avons également étudié l'adhésion cellulaire avec des lymphocytes-T sur des surfaces de PDMS d'élasticité variable. Nous avons montré que contrairement à la plupart des autres types de cellules, les cellules-T s'étalent davantage sur substrat mou que sur dur. Finalement nous avons réalisé des expériences pilotes d'adhésion cellulaire sur PDMS structuré. / In the past decade, more and more types of cells have been shown to be capable of probing the mechanics of their environment by application of forces. The stiffness of the environment strongly influences a host of cellular parameters including cell adhesion and mechanics. In separate studies, the spatial distribution of ligands, modulated by chemical patterning of a target surface, has been shown to strongly influence cell adhesion and mechanics. However, the cross-talk between the two phenomena has not been much explored, partly because patterned functionalization of soft substrates is an engineering challenge. To address this issue, we have developed a simple and technique named "reverse contact printing" for fabrication of nanometric protein patches on PDMS (polydimethylsiloxane) elastomer. My PhD work consisted of deciphering the molecular mechanisms that underlie this technique. We realized that the rate of transfer crucially depended on the molecular groups on the protein and on the nature of the PDMS surface. We used atomic force microscopy (AFM) force measurements to measure PDMS elasticity as well as protein-substrate interactions to understand the molecular mechanism governing the transfer. We have identified that a successful reverse transfer is facilitated by the grafting of appropriate chemical groups on the protein, and depends on the PDMS surface treatment and elasticity. We also studied adhesion and mechanics of T lymphocytes on PDMS. We found that surprisingly T lymphocytes spread more on softer than on harder PDMS. In on-going pilot experiments, cells on patterned soft PDMS seem to exhibit different behavior as compared to cells on patterned glass.

Grâce à leurs propriétés physiques/chimiques uniques, les nanoparticules colloïdales sont au cœur de nombreuses applications innovantes. Afin de faciliter leur caractérisation ou de les intégrer dans des dispositifs fonctionnels, il est nécessaire de les assembler de manière dirigée sur des surfaces solides. Dans ce contexte, l’objectif de cette thèse est de mieux comprendre et d’optimiser la technique de nanoxérographie, méthode d’assemblage dirigé où des nanoparticules sont piégées sur des motifs de charges électrostatiques. Après un premier travail consistant à améliorer le procédé de nanoxérographie, trois problématiques spécifiques ont été adressées : (i) l’assemblage de particules micrométriques. Le couplage de simulations numériques et de manipulations expérimentales a permis d’identifier les paramètres clés de l’assemblage de telles particules colloïdales et d’élargir (facteur 100) la gamme de tailles de particules assemblables par nanoxérographie. (ii) l’analyse de l’assemblage multicouche. Par le biais de nanoparticules modèles luminescentes et par la mise en place d’un nouveau protocole d’assemblage, les critères clés génériques pour l’assemblage 3D de colloïdes par nanoxérographie ont été dégagés. (ii) l’assemblage dirigé de nanogels sensibles à un stimulus environnemental extérieur. L’utilisation d’un protocole d’assemblage optimisé a permis d’élaborer des assemblages de nanogels interactifs avec leur environnement et du faire du tri sélectif de ces nanoparticules sur une même surface. / Owing to their unique physico-chemical properties, colloidal nanoparticles are building blocks for the creation of plentiful innovative devices. In order to make easier their characterization and to incorporate them into functional nano-devices, it is necessary to perfectly control their directed assemblies onto solid surfaces. In this context, this thesis’ purpose is to simultaneously better understand and optimize the nanoxerography method, which allows electrostatic and selective directing assemblies of nanoparticles onto charged patterns. After an optimization of the nanoxerography process, three specific problematics have been addressed: (1) micron-sized particles assembly. The combined use of numerical simulations and experiments enabled to unveil the key parameters involved in micron-sized particles assembly and to expend the particle size range foreseeable for an assembly by nanoxerography (factor 100). (2) the 3D assembly analysis. The influence of diverse parameters on the 3D assembly of luminescent model nanoparticles was quantified by using a new assembly protocol. The results gave the generic key criterions for the 3D assembly of colloids by nanoxerography. (3) directed assembly of nanogels sensitive to an external environmental stimulus. The use of an optimized protocol allowed elaborating nanogels assemblies interactive with their environment and to sort these nanoparticles onto the same surface.

Radio-frequency microelectromechanical systems (RF~MEMS) are highly miniaturized devices intended to switch, modulate, filter or tune electrical signals from DC to microwave frequencies. The micromachining techniques used to fabricate these components are based on the standard clean-room manufacturing processes for high-volume integrated semiconductor circuits. RF~MEMS switches are characterized by their high isolation, low insertion loss, large bandwidth and by their unparalleled signal linearity. They are relatively simple to control, are very small and have almost zero power consumption. Despite these benefits, RF~MEMS switches are not yet seen in commercial products because of reliability issues, limits in signal power handling and questions in packaging and integration. Also, the actuation voltages are typically too high for electronics applications and require additional drive circuitry. This thesis presents a novel MEMS switch concept based on an S-shaped film actuator, which consists of a thin and flexible membrane rolling between a top and a bottom electrode. The special design makes it possible to have high RF isolation due to the large contact distance in the off-state, while maintaining low operation voltages due to the zipper-like movement of the electrostatic dual-actuator. The switch comprises two separately fabricated parts which allows simple integration even with RF circuits incompatible with certain MEMS fabrication processes. The two parts are assembled by chip or wafer bonding which results in an encapsulated, ready-to-dice package. The thesis discusses the concept of the switch and reports on the successful fabrication and evaluation of prototype devices. Furthermore, this thesis presents research results in wafer-level packaging of (RF) MEMS devices by full-wafer bonding with an adhesive intermediate layer, which is structured before bonding to create defined cavities for housing MEMS devices. This technique has the advantage of simple, robust and low temperature fabrication, and is highly tolerant to surface non-uniformities and particles in the bonding interface. It allows cavities with a height of up to many tens of micrometers to be created directly in the bonding interface. In contrast to conventional wafer-level packaging methods with individual chip-capping, the encapsulation is done using a single wafer-bonding step. The thesis investigates the process parameters for patterned adhesive wafer bonding with benzocyclobutene, describes the fabrication of glass lid packages based on this technique, and introduces a method to create through-wafer electrical interconnections in glass substrates by a two-step etch technique, involving powder-blasting and chemical etching. Also, it discusses a technique of improving the hermetic properties of adhesive bonded structures by additional passivation layers. Finally, it presents a method to substantially improve the bond strength of patterned adhesive bonding by using the solid/liquid phase combination of a patterned polymer layer with a contact-printed thin adhesive film. / QC 20100617

Cell adhesion to extracellular matrices (ECM) is critical to many cellular processes including differentiation, proliferation, migration, and apoptosis. Alterations in adhesive mechanisms are central to the behavior of cells in pathological conditions including cancer, atherosclerosis, and defects in wound healing. Although significant progress has been made in identifying molecules involved in adhesion, the mechanisms that dictate the generation of strong adhesive forces remain poorly understood. Specifically, the role of nanoscale geometry of the adhesive interface in integrin recruitment and adhesion forces remains elusive due to limitations in the techniques available for engineering cell adhesion environments. The objective of this project was to analyze the role of nanoscale geometry in cell adhesion strengthening to ECM. Our central hypothesis was that adhesive interactions are regulated by integrin clusters whose recruitment is determined by the nanoscale geometry of the adhesive interface and whose heterogeneity in size, spacing, and orientation modulates adhesion strength. The objective of this project was accomplished by 1) developing an experimental technique capable of producing nanoscale patterns of proteins on surfaces for cell adhesion arrays, 2) assessing the regulation of integrin recruitment by geometry of the adhesive interface, and 3) determining the functional implications of adhesive interface geometry by systematically analyzing the adhesion strengthening response to nanoscale patterns of proteins. A printing technique was developed that patterns proteins into features as small as 90nm with high contrast and high reproducibility. Cell adhesion arrays were produced by directly immobilizing proteins into patterns on mixed-SAMs surfaces with a protein-resistant background. Colocalization analysis of integrin recruitment to FN patterns demonstrated a concentrating effect of bound integrins at pattern sizes with areas equivalent to small nascent focal adhesions. At adhesion areas below 333 × 333 nm2, the frequency of integrin recruitment events decreased significantly indicating a threshold size for integrin clustering. Functionally, pattern sizes below the threshold were unable to participate in generation of adhesion strength. In contrast, patterns between the threshold and micron sizes showed a relationship between adhesion strength and area of individual adhesion points, independent of the total available adhesion area. These studies introduce a robust platform for producing nanoscale patterns of proteins in biologically relevant geometries. Results obtained using this approach yielded new insights on the role of nanoscale organization of the adhesive interface in modulating adhesion strength and integrin recruitment.

No description available.