Orientador: Elaine Maria Cardoso / Resumo: A energia solar pode ser aproveitada como fonte de energia térmica para aquecimento de água, por exemplo, em coletores solares ou como fonte de energia elétrica usando sistemas de células fotovoltaicas. Entretanto, as células fotovoltaicas, geralmente, de custos relativamente altos, têm algumas restrições relacionadas a altas temperaturas de operação e distribuições de temperatura não homogêneas levando a redução da vida útil e eficiência elétrica de tais sistemas. Essas limitações têm sido o foco de pesquisas, a fim de melhorar as eficiências elétricas, regular as temperaturas de operação e reduzir os materiais necessários para fabricação das células. Assim, este projeto de pesquisa tem como objetivo avaliar o desempenho de um dissipador de calor, baseado em microcanais retangulares paralelos, no resfriamento de uma célula fotovoltaica de alta concentração (HCPV-High Concentration Photovoltaic Cell), utilizando-se de análise teórica (modelo térmico), simulação numérica (usando o software comercial CFD ANSYS® Fluent v15) e de uma bancada experimental. Neste trabalho, foram consideradas as condições de máxima radiação (denominado de pior cenário, quando a célula não gera eletricidade e todo o calor deve ser dissipado) e de radiação média ao longo do período considerado. Os dados climatológicos foram obtidos do site Canal Clima - UNESP, com dados historicos do clima na região noroeste paulista. Foi realizada uma revisão do estado da arte a fim de compreender como os sistemas de... (Resumo completo, clicar acesso eletrônico abaixo) / Abstract: Solar energy can be used as a source of thermal energy in solar collectors, for example, or as a source of electricity using photovoltaic cell systems. However, photovoltaic cells requires high investments having some restrictions related to high operating temperatures and nonhomogeneous temperature distributions, leading to a reduction in the useful life and electrical efficiency. These limitations have been the focus of researches in order to improve electrical efficiencies, to regulate operating temperatures, and to reduce required materials in the cells. Thus, this research project aims to evaluate the performance of a heat sink based on parallel rectangular microchannels for cooling of a high concentration photovoltaic cell (HCPV), using theoretical analysis (thermal model), numerical simulation (using commercial software CFD ANSYS® Fluent v15) and an experimental bench. In this work, it was considered the conditions of maximum radiation (named worst scenario, when the cell does not generate electricity and all the heat must be dissipated) and the average radiation over the period considered. These climatological data were obtained from the Canal Clima – UNESP site, in the northwestern region of São Paulo state. A review on the subject was carried out in order to understand how solar photovoltaic systems can be optimized using solar concentrators and more efficient materials (multiple-junction cells). The influence of temperature and cooling systems were analyzed. An exp... (Complete abstract click electronic access below) / Mestre

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Nuclear Engineering, 1980. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND SCIENCE. / Includes bibliographical references. / by King-Wo Thomas Chiu. / M.S.

Thesis: Ph. D., Massachusetts Institute of Technology, Department of Mechanical Engineering, 1982 / Includes bibliographical references. / by Paul Douglas Symolon. / Ph. D. / Ph. D. Massachusetts Institute of Technology, Department of Mechanical Engineering

Internal combustion engines, electric motors and batteries generate a significant amount of heat during operation that needs to be extracted by cooling systems. A cooling system is designed and installed to extract the generated heat and maintain the system temperature in an optimal range. Overheating has several unfavorable outcomes such as less durability and lower energy efficiency. The cooling system consists of several components such as hoses, flow splitters, valves, heat exchangers, coolant, pump, etc. The coolant, as the working fluid, is pumped to different heat generator component to enable the cooling down process. Computational Fluid Dynamics (CFD) is a powerful and cost efficient tool to simulate the cooling processes, design, and evaluate the performance of a cooling system. Generally, one dimensional CFD is a common approach to interpret and explain the cooling processes in the automotive industry due to its high flexibility and computational cost efficiency. Also, three dimensional CFD is employed whenever it is required to study complex physical phenomena and provide detailed information. Additionally, it is possible to couple one dimensional and three dimensional CFD approaches to simulate cooling processes. Not only is the coupled 1D-3D CFD approach able to capture complicated physical processes but also is flexible and cost efficient. The objective of this master thesis is to implement 1D-3D CFD coupled simulation on internal combustion engines’ cooling system and evaluate the advantages and disadvantages of this method. The performance of this method is examined in different case studies with different flow and geometrical characteristics. The effect of various turbulence models and numerical settings are investigated on the quality of the coupled simulations’ results. The coupled simulations are carried out using GT-SUITE and STAR-CCM+ software. The performed simulations show that the coupling method is a convenient approach which is able to capture detailed physics with high precision requiring reasonable computational costs. The results of the coupled simulations depict agreement with the uncoupled 1D CFD simulations, although some discrepancies are observed in complex case studies. Also, it is shown that the coupled simulations are sensitive to numerical settings and physical models, consequently, the case setup should be optimized carefully. / Förbränningsmotorer, elmotorer och batterier genererar en betydande mängd värme under drift som behöver extraheras av kylsystem. Ett kylsystem är utformat och installerat för att extrahera den genererade värmen och hålla systemtemperaturen i ett optimalt intervall. Överhettning har flera ogynnsamma följder, som mindre hållbarhet och lägre energieffektivitet. Kylsystemet består av flera komponenter, till exempel slangar, flödesdelare, ventiler, värmeväxlare, kylvätska, pump etc. Kylvätskan, som arbetsvätska pumpas till olika värmegenerator-komponenter för att möjliggöra nedkylningsprocessen.Computational Fluid Dynamics (CFD) är ett kraftfullt och kostnadseffektivt verktyg för att simulera kylprocesserna, utforma och utvärdera prestanda för ett kylsystem. I allmänhet är endimensionell CFD en vanlig metod för att tolka och förklara kylningsprocesserna i bilindustrin på grund av dess höga flexibilitet och beräkningseffektivitet. Dessutom används tredimensionell CFD när det krävs, för att studera komplexa fysiska fenomen och tillhandahålla detaljerad information. Dessutom är det möjligt att koppla ihop en- och tredimensionell CFD-metod för att simulera kylningsprocesser. Inte bara är den kopplade 1D-3D CFD-metoden möjlig för att betrakta komplicerade fysiska processer, utan är även flexibel och kostnadseffektiv.Syftet med detta examensarbete är att implementera 1D-3D CFD kopplad simulering på förbränningsmotorns kylsystem och utvärdera fördelarna och nackdelarna med denna metod. Uppträdandet av denna metod undersöks i olika fallstudier med olika flöde och geometriska egenskaper. Effekterna av olika turbulensmodeller och numeriska inställningar undersöks genom kvaliteten på resultaten hos kopplingens simuleringar. De kopplade simuleringarna utförs med hjälp av mjukvaran GT-SUITE och STAR CCM +.De utförda simuleringarna visar att kopplingsmetoden är ett bekvämt tillvägagångssätt som kan fånga detaljerad fysik med hög precision till rimliga beräkningskostnader. Resultaten av de kopplade simuleringarna visar överensstämmelse med de frikopplade 1D CFD-simuleringarna, även om vissa avvikelser observeras i komplexa fallstudier. Det visas också att de kopplade simuleringarna är känsliga för numeriska inställningar och fysiska modeller, därför bör fallinställningen optimeras noggrant.

Thesis (MScEng (Mechanical and Mechatronic Engineering))--University of Stellenbosch, 2010. / ENGLISH ABSTRACT: The thesis was initiated by a Consulting Engineering Company (KV3) as a research project to investigate various options in which the efficiency and energy utilisation of conventional air conditioning systems may be enhanced by using alternative and renewable energy. Initially, eight options had been identified and through a process of determining the degree of commercialisation the alternative options were reduced to three. These options, referred to as the sustainable cooling alternatives, are active mass cooling, night flushing and roof cooling system. The roof cooling system comprised a roof-pond, roof-spray, pump and storage tank. The roof cooling system was mathematically and experimentally modelled. The roof cooling experiment was performed under a variety of weather conditions with the roof-pond and storage tank temperatures continuously recorded. The experimentally recorded temperatures were compared to the temperatures generated by the theoretical simulation calculations for the same input and weather conditions. Good agreement was found between the mathematical and experimental model. The largest discrepancy found between the simulated temperature and the experimental temperature was in the order of 1 ºC. A one-room building has been assumed to serve as a basis to which the sustainable cooling alternatives could be applied to for theoretical simulation. The one-room building had four façade walls and a flat roof slab. Night flushing, active mass cooling and the roof cooling system were applied to the one-room building such that the room air temperature and space cooling load could theoretically be simulated. The theoretical simulations were also repeated for the case where the roof-pond and roof-spray were applied as standalone systems to the one-room building. The theoretical simulation calculations were performed for typical summer weather conditions of Stellenbosch, South Africa. Under base case conditions and for a room thermostat setting of 22 ºC the peak cooling load of the one-room building was 74.73 W/m². With the application of night flushing between the hours of 24:00 and 07:00, the room cooling load was reduced by 5.2% by providing 3.9 W/m² of cooling and reducing the peak room temperature by 1.4 ºC. The active mass cooling system was modelled by supplying water at a constant supply temperature of 15 ºC to a pipe network embedded in the roof slab of the one-room building. The sea may typically be considered as a cold water source for buildings situated at the coast. The active mass cooling system reduced the peak cooling load of the one-room building by 50% by providing 37.2 W/m² of cooling and reducing the peak room temperature by 6.7 ºC. When the roof-spray and roof-pond systems were applied as standalone systems to the oneroom building, the peak cooling load of the one-room building could be reduced by 30% and 51% respectively. This is equivalent to 22.3 W/m² of peak cooling by the roof-spray and 38 W/m² of peak cooling by the roof-pond. The roof-spray reduced the peak room temperature by 3.71 ºC while the roof-pond reduced the peak room temperature by 5.9 ºC. Applying the roof cooling system to the one-room building produced 46 W/m² of peak cooling which resulted in a 61.1% reduction in peak cooling load. The roof cooling system reduced the peak temperature by 8 ºC. By comparing the sustainable cooling alternatives, the roof cooling system showed to be the most effective in reducing the one-room building peak cooling load. Over a 24 hour period the roof cooling system reduced the net heat entry to the one-room building by 57.3%. In a further attempt to reduce the peak cooling load, the sustainable cooling alternatives were applied in combinations to the one-room building. The combination of night flushing and roof-spray reduced the peak cooling load by 36% while a combination of night flushing and active mass cooling reduced the peak cooling load by 55%. Combining night flushing with the roof-pond also yielded a 55% peak cooling load reduction. The combination of roofpond, active mass cooling and night flushing provided 51 W/m² of cooling which corresponded to a 68% reduction in peak cooling load. Utilising the sustainable cooling alternatives in a combination in the one-room building gave improved results when compared to the case where the sustainable cooling alternatives were employed as standalone systems. It is illustrated by means of a sensitivity analysis that the ability of the roof cooling system to produce cool water is largely influenced by ambient conditions, droplet diameter and roofspray rate. Under clear sky conditions, an ambient temperature of 15 ºC, relative humidity of 80%, a roof-spray rate of 0.02 kg/sm² and a roof-pond water level of 100mm, water could be cooled at a rate of 113 W/m². The roof-spray energy contributed to 28 W/m² whilst the night sky radiation was responsible for 85 W/m² of the water cooling. It must however be noted that the water of the roof cooling system can never be reduced to a temperature that is lower than the ambient dew point temperature. / AFRIKAANSE OPSOMMING: Die tesis is geïnisieer deur ‘n Raadgewende Ingenieurs Maatskappy (KV3) as a navorsingsprojek om verskeie opsies te ondersoek waarmee die effektiwiteit en energie verbruik van konvensionele lugversorgingstelsels verbeter kan word deur middel van alternatiewe en hernubare energie. Agt opsies is oorspronglik geïdentifiseer en deur middel van ‘n proses waarby die graad van kommersialisering van hierdie alternatiewe maniere bepaal is, kon die opsies verminder word tot drie. Hierdie opsies, ook verwys na as die volhoubare verkoelingsalternatiewe, sluit in aktiewe massa verkoeling, dakverkoeling en nagventilasie. Die dakverkoelingstelsel bestaan uit dakwater, ‘n dakspuit, ‘n pomp en ‘n stoortenk. Die dakverkoelingstelsel is wiskundig en eksperimenteel gemodelleer. Die dakverkoelingseksperiment is uitgevoer onder ‘n verskeidenheid van weersomstandighede. Die dakwater asook die stoortenk se water temperatuur is voortdurend aangeteken. Dieselfde weer- en insetkondisies is gebruik vir die simulasie berekening en die temperature van die stoortenk se water en die dakwater is vergelyk met die temperatuurlesings van die eksperimentele werk. Die temperature van die eksperimentele lesings het goed vergelyk met die temperatuur simulasie berekeninge. Die grootste verskil tussen die simulasie en eksperimentele temperatuur was in die orde grootte van 1 ºC. ‘n Een-kamer gebou is aangeneem om as basis te dien waarop die volhoubare verkoelingsalternatiewe aangewend kon word vir teoretiese simulasie. Die een-kamer gebou het uit vier buite mure en ‘n horisontale beton dak bestaan. Nag ventilasie, aktiewe massa verkoeling en die dakverkoelingstelsel is toegepas op die een-kamer gebou en die kamer se verkoelingslas asook die kamer se lugtempertuur is teoreties gesimuleer. Die teoretiese simulasies is ook herhaal vir die geval waar die dakwater and dakspuitstelsel apart aangewend is op die een-kamer gebou. Die teoretiese simulasie berekeninge is uitgevoer vir tipiese somer weersomstandighede vir Stellenbosch, Suid Afrika. Onder basisgeval omstandighede, waar die een-kamer gebou gesimuleer is, sonder enige volhoubare verkoelingsalternatiewe en ‘n termostaat verstelling van 22 ºC, is die piek verkoelingslas bereken as 74.73 W/m². Met die toepassing van nagventilasie tussen die ure 24:00 en 07:00 was die piekverkoelingslas van die kamer verminder met 5.2% deur 3.9 W/m² se verkoeling te verskaf en die piekkamer temperatuur te verminder met 1.4 ºC. Aktiewe massa verkoeling is gesimuleer deur water teen ‘n konstante temperatuur van 15 ºC te verskaf aan ‘n pypnetwerk, geïnstalleer in the beton dak, van die een-kamer gebou. Geboue geleë aan die kus kan tipies seewater oorweeg as ‘n bron van koue water. Aktiewe massa verkoeling het die piekverkoelingslas van die een-kamer gebou verminder met 50% deur 37.2 W/m² se verkoeling te verskaf en die piekkamer temperatuur te verminder met 6.7 ºC. Wanneer die dakspuit- en dakwaterstelsel aangewend is op die een-kamer gebou as enkel staande stelsels, is die piekverkoelingslas verminder met 30% en 51% onderskeidelik. Dit is ekwivalent aan 22.3 W/m² se verkoeling vir die dakspuitstelsel en 38 W/m² se verkoeling vir die dakwaterstelsel. Die dakspuitstelsel het die piekkamer temperatuur verminder met 3.71 ºC terwyl die dakwaterstelsel ‘n 5.9 ºC verlaging in piekkamer temperatuur tot gevolg gehad het. Die dakverkoelingstelsel het 46 W/m² se piekverkoeling verskaf wat ‘n 61.1% vermindering in piekverkoelingslas tot gevolg gehad het. Die ooreenstemmende piek temperatuur vermindering is 8 ºC. Deur die verskeie volhoubare verkoelingsalternatiewe met mekaar te vergelyk, word getoon dat die dakverkoelingstelsel die mees effektiefste manier is om die een- kamer se piekverkoelingslas te verminder. Oor ‘n tydperk van 24 uur het die dakverkoelingstelsel die totale energievloei na die een-kamer gebou met 57.3% verminder. In ‘n verdere poging om die piekverkoelingslas te verminder, is die volhoubare verkoelingsalternatiewe toegepas in kombinasies op die een-kamer gebou. Die kombinasie van nagventilasie met die dakspuitstelsel het die piekverkoelingslas met 36% verminder, terwyl ‘n kombinasie van nagventilasie en aktiewe massa verkoeling ‘n 55% vermindering in piekverkoelingslas tot gevolg gehad het. Die kombinasie van dakwater en nagventilasie het ook ‘n piekverkoelingslas vermindering van 55% teweeggebring. Die kombinasie van dakwater, aktiewe massa verkoeling en nagventilasie het 51 W/m² se verkoeling veskaf, wat ooreenstem met ‘n 68% vermindering in piekverkoelingslas. Deur die volhoubare verkoelingsalternatiewe in kombinasies toe te pas op die een-kamer gebou, kon beter resultate verkry word toe dit vergelyk is met die geval waar die volhoubare verkoelingsalternatiewe as enkelstaande stelsels toegepas is. Dit is geïllustreer deur middel van ‘n sensitiwiteitsanalise dat die vermoë van die dakverkoelingstelsel om koue water te produseer, beïnvloed word deur buitelug kondisies, waterdruppel deursnee en dakspuit massa vloeitempo. Onder die oop hemelruimteomstandighede, ‘n buitelug temperatuur van 15 ºC, ‘n relatiewe humiditeit van 80%, ‘n dakspuit massa vloeitempo van 0.02 kg/sm² en dakwatervlak van 100 mm, kon water verkoel word teen ‘n tempo van 113 W/m². Die dakspuit gedeelte het 28 W/m² bygedra terwyl die nagruim radiasie sowat 85 W/m² se verkoeling verskaf het. Daar moet egter kennis geneem word dat die water temperatuur van die dakverkoelingstelsel nooit verminder kan word tot onder die buitelug doupunttemperatuur nie.

The supply of cooling has increased significantly in recent years, the trend shows that the increase will continue one reason is that the standard of living has increased, but EU has also set a requirement that energy consumption must be better at the same time. With “better” means more efficient and environmentally friendly. District cooling today uses either chillers or naturally available cold sources such as deep sea water, lake water or cold air. Cold air is, of course, only available when the seasons permit it and the cold air is not available when comfort cooling is needed for e.g. offices. The only alternative for areas that do not have a cold water source nearby is to use chillers. The most common chillers today are compressor chillers and absorption chillers. The most interesting chiller for the energy and environmental company HEM in Halmstad, is the absorption chiller which is driven by heat. HEM has, during the summer, surplus heat produced in Kristinehed plant which they want to use, they also have an increased inventory of waste during the summer which they get from the municipality of Halland. This heat is, of course, qualified to be used in the making of cold. Absorption chillers is today, however, not as common as compressor chillers which are capable of dealing with most cooling capacities, from small to large, and simultaneously works more or less flawlessly. Most of today’s absorption chillers are of a few hundred kW and upwards while there are no absorption chillers for the smaller effects, they are also very expensive and can have problems with crystallization of the absorbent if the operation is handled incorrectly. But it’s also expensive when it comes to piping of district cooling networks depending on where the pipes are desired, for example if it is the middle of town or over a grass field. A fictional project of the area Sannarp is used for a case study in this thesis where one investment alternative was to extend the existing district cooling pipes and another alternative was to invest in absorption chillers to meet the company's cooling demand. The results were obviously much affected by the area's layout and the distance to the first company starting from the existing pipe. The company's cooling demand also affected the results and the first alternatives investment cost could only be competitive with alternative 2 because the distance was just of the right length. If the distance to the company had been shorter, then the cooling demand for the same company has had to be less. The conclusion of the project was still in the end that and expansion of the current district cooling network to the company was the most feasible and economically advantageous.

M. Tech. (Engineering, Electrical, Department Electronic Engineering, Faculty of Engineering and Technology), Vaal University of Technology / In order to facilitate sustainable development, it is necessary to further improve and increase the energy efficiency and use of renewable energy and its related technologies. The main limiting factors to the extensive use of photovoltaic (PV) modules include the high initial investment cost and the relatively low conversion efficiency. However, other factors, such as an increase in ambient temperature, exert a considerable negative influence on PV modules, with cell efficiencies decreasing as the cell’s operating temperature increases. Higher PV module surface temperatures mean lower output voltages and subsequent lower output power. Therefore, this dissertation focuses on optimizing the available output power from a PV module by investigating and controlling the effect that the PV module’s surface temperature exerts on the amount of electrical energy produced. A pilot study was conducted by using a PV module set to three different tilt angles with an orientation angle and temperature sensors placed at different points. This was done to determine temperature distribution on the PV module surfaces as well as identify which tilt angle produces the highest PV module surface temperature. The main study was designed to investigate the electrical performance of a PV module with different cooling systems (water and forced air) as against a referenced measurement (no cooling). The cooling systems will be switched on and off at specific time intervals with the help of an electronic timer circuit incorporating a PIC microcontroller. The pilot study was conducted for a 50 week period where the results indicated a direct correlation between temperature rise and voltage decrease. The PV module’s temperature is highest at a tilt angle of 16° during the day and lowest at night time. It further reveals that the PV module’s front and back surface temperature can be distinctly different, with the highest recorded values occurring at the back of the PV module. The main study was conducted for a period of 15 weeks with results indicating that the water cooling system resulted in an average higher output power of 49.6% when compared to the reference system (no cooling system). Recommendations are made that sufficient space should be included between the module frames and mounting structure to reduce high operating temperatures owing to poor air circulation.

Presently information systems are increasingly penetrating to our daily life. Recently it is relevant to integrate the newest technologies. In that way traditional system becomes “smart” who are more economical, optimal, and self-sufficient. The biggest problem is to make a model of “smart” system. There were analyzed modeling methods, heating and cooling control systems in this job. Mathematical model for heating and cooling controller using timed Petri nets was presented. According to analyzed problems it was made verification with Matlab during experimental phase. There was made comparison evaluation of mathematical model made with timed Petri nets and fuzzy logic.

Made available in DSpace on 2016-06-02T20:09:08Z (GMT). No. of bitstreams: 1 1646.pdf: 3878244 bytes, checksum: 1b913364f7458c2e95fc16bda01f835e (MD5) Previous issue date: 2007-08-01 / Financiadora de Estudos e Projetos / This research focuses the evaporative cooling by water aspersion on wavy cement fiber tiles in the city of São Carlos, SP, seeking to use it to reduce the buildings heat gains. A theoretical model was developed, based on classic equations of fluids mechanic, applied to iterative calculations of heat flows on the tile superior surface, considered as control surface. In the work development, this model was progressively adjusted to experimental data obtained in a test cell, exposed to the local climatic conditions, with the monitoring of superficial temperatures of both faces in two tiles, one maintained dry and other under intermittent aspersion of water. The research results indicated that, despite of still being susceptible to improvement, the theoretical model already presents quite satisfactory approach with the measured data. Applying a statistical adjustment to the proposed model of iterative heat flows calculation, it was obtained a correlation coefficient between measured and estimated temperatures of 0,999 and a standard deviation of 0,35 ºC. During the experiments, the average evaporative heat flow was 409 W/m2. Theaverage water volume evaporated was 0,7 l/(m².h), corresponding to an average difference of temperatures among the compared tiles of 5,12 K, for the daylight period. Due to the growing need of energy consumption reduction, this procedure seems to be a good option to reduce buildings thermal load, if compared to conventional air conditioning systems / Esta pesquisa enfoca a refrigeração evaporativa por aspersão de água sobre telhas onduladas de fibrocimento, na cidade de São Carlos, SP, visando sua utilização para redução dos ganhos de calor em edificações. Um modelo teórico foi desenvolvido, baseado em equações clássicas da mecânica dos fluidos, aplicadas em cálculos iterativos dos fluxos de calor sobre a superfície superior da telha, considerada como superfície de controle. No desenvolvimento do trabalho, este modelo foi progressivamente ajustado a dados experimentais obtidos em uma célula de teste, exposta às condições climáticas locais, sendo monitoradas temperaturas superficiais de ambas as faces em duas telhas, uma mantida seca e outra sob aspersão intermitente de água. Os resultados da pesquisa indicaram que, apesar de ainda ser passível de aprimoramento, o modelo teórico já apresenta aproximação bastante satisfatória com os dados medidos. Aplicando-se um ajuste estatístico ao modelo proposto de cálculo iterativo dos fluxos de calor, obteve-se um coeficiente de correlação entre temperaturas medidas e estimadas de 0,999 e um desvio padrão de 0,35 ºC. Durante os experimentos, o fluxo médio de calor por evaporação foi de 409 W/m2. O volume médio de água evaporado foi de 0,7 l/(m².h), correspondendo a uma diferença média de temperaturas entre as telhas comparadas, para o período diurno, de 5,12 K. Frente à crescente necessidade de redução de consumo de energia, esta parece uma boa opção para redução da carga térmica dos edifícios, se comparada aos sistemas convencionais de condicionamento de ar

Made available in DSpace on 2014-10-09T12:55:30Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:07:16Z (GMT). No. of bitstreams: 0 / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP