The aim of this research work was to improve the compatibility of polymer blends made from poly(lactic acid) and natural rubber (PLA/NR blends) by using modified natural rubber as a compatibilizer. Natural rubber was chemically modified into two categories: natural rubber grafted poly(vinyl acetate) copolymer (NR-g-PVAc) and block copolymers (PLA-NR diblock copolymer and PLA-NR-PLA triblock copolymer). PLA/NR blends were prepared by melting blending in a twin screw extruder and compression molded to obtain a 2-mm thick sheet. The blends contained 10-20 wt% of NR and modified NR, and the impact strength and tensile properties were investigated. The compatibilization effect was determined by DMTA, DSC and SEM. NR-g-PVAc was synthesized by emulsion polymerization to obtain different PVAc graft contents (1%, 5% and 12%). Characterization by DMTA showed an enhancement in miscibility of the PLA/NR-g-PVAc blends. NR-g-PVAc could be used as a toughening agent of PLA and as a compatibilizer of the PLA/NR blend. The block copolymers were synthesized following two routes: (1) hydroxyl telechelic natural rubber (HTNR) and lactide and (2) HTNR and PLA prepolymer. In the former route, lactide was in situ polymerized via a ring opening polymerization to be a PLA block segment during block copolymerization. In the latter route PLA prepolymer was synthesized by a condensation polymerization of L-lactic acid prior to block copolymerization. Both block copolymers acted as good compatibilizers for the PLA/NR blend by increasing the impact strength and decreasing the NR particle size. Triblock copolymers provided higher impact strength than diblock copolymers, and they were a less effective compatibilizer than NR-g-PVAc. In contrast to NR and NR-g-PVAc, the block copolymer was not a good toughening agent for PLA.

Synthesis of 2-[(3-thienylcarbonyl)oxy]ethyl 3-thiophene carboxylate (TOET), 2,3-bis-[(3-thienylcarbonyl)oxy]propyl 3-thiophene carboxylate (TOPT), and 3-[(3-thienylcarbonyl)oxy]-2,2-bis{[(3-thienylcarbonyl)oxy]}propyl 3- thiophene carboxylate (TOTPT), and their copolymerization either with thiophene or pyrrole were achieved. The chemical structures of the monomers were investigated by Nuclear Magnetic Resonance Spectroscopy (NMR) and Fourier Transform Infrared Spectroscopy (FTIR). Electrochemical behavior of the monomers and copolymers were studied by cyclic voltammetry (CV). The resultant conducting copolymers were characterized via FTIR, Thermal Gravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC), and morphologies of the films were inspected by Scanning Electron Microscope (SEM). Conductivities of the samples were measured by using four-probe technique. The electrochromic and spectroelectrochemical properties of the copolymers were investigated.

Synthesis and characterization of conducting copolymers were achieved by using thiophene-3-yl acetic acid cholesteryl ester (CM) and poly (3-methylthienyl methacrylate) (PMTM). A new polythiophene containing a cholesteryl side chain in the &amp / #946 / -position was chemically polymerized in nitromethane/carbon tetrachloride using FeCl3 as the oxidizing agent. Polymerization was also achieved by constant current electrolysis in dichloromethane. Subsequently, conducting copolymers of thiophene-3-yl acetic acid cholesteryl ester (CM), PCM1 (obtained from chemical polymerization method), PCM4 (obtained from constant current electrolysis) with pyrrole were synthesized. Thiophene functionalized methacrylate monomer (MTM) was synthesized via esterification of the 3-thiophene methanol with methacryloyl chloride. The methacrylate monomer was polymerized by free radical polymerization in the presence of azobis (isobutyronitrile) (AIBN) as the initiator. Graft copolymers of poly (3-methylthienyl methacrylate)/polypyrrole, (PMTM2/PPy) and poly (3-methylthienyl methacrylate)/polythiophene, (PMTM2/PTh) were synthesized by constant potential electrolyses. PMTM2 coated Pt electrodes were utilized as the anode in the polymerization of pyrrole and thiophene. Moreover, oxidative polymerization of PMTM1 was studied by galvanostatic and chemical techniques. Characterizations of the samples were performed by CV, FTIR, NMR, DSC, TGA and SEM analyses. Electrical conductivities were measured by the four-probe technique. Immobilization of invertase in conducting copolymer matrices, poly (3-methylthienyl methacrylate) with pyrrole and thiophene was achieved by constant potential electrolysis using the sodium dodecyl sulfate as the supporting electrolyte. Polythiophene was also used for immobilization matrices. Cholesterol oxidase has been immobilized in conducting copolymer of thiophene-3-yl acetic acid cholesteryl ester with polypyrrole (CM/PPy) and polypyrrole (PPy) by the electropolymerization method. p-Toluene sulfonic acid was used as a supporting electrolyte. Kinetic parameters (Kinetic parameters / Vmax and Michaelis-Menten constant / Km) and operational stability of enzyme electrodes were investigated. Surface morphology of the films was also examined.

Synthesis and characterization of thiophene ended poly-&amp / #949 / -caprolactone (PCL) and oxalic acid dithiophen-3-yl methyl ester (ODME) and their copolymers with both pyrrole and thiophene were achieved. Chemical structure of the precursor polymer and monomer were investigated Redox behavior of polymer and monomers were determined by Cyclic Voltammetry (CV). Structural characterization of samples were carried out by 1H, 13C Nuclear Magnetic Resonance (NMR) and Fourier Transform Infrared Spectroscopy (FTIR). Conductivities of the films were measured by using four probe technique. Thermal analyses of conducting copolymers were investigated via Differential Scanning Calorimetry (DSC) and Thermal Gravimetry Analysis (TGA). The morphologies of the copolymer films were examined by Scanning Electron Microscopy (SEM). Electrochromic and spectroelectrochemical behavior of the copolymers were investigated, and their ability of employment in device construction has been examined.

Immobilization of tyrosinase in conducting copolymer matrices of pyrrole functionalized polydimethylsiloxane/polypyrrole (PDMS/PPy) were achieved by electrochemical polymerization. The polysiloxane/polypyrrole/tyrosinase electrode was constructed by the entrapment of enzyme in conducting matrices during electrochemical copolymerization. Maximum reaction rate (Vmax) and Michaelis-Menten constant (Km) were investigated for immobilized enzyme. Enzyme electrodes were prepared in two different electrolyte/solvent systems. The effect of supporting electrolytes, p-toluene sulfonic acid and sodium dodecyl sulfate on the enzyme activity and film morphology were determined. Temperature and pH optimization, operational stability and shelf-life of enzyme electrodes were also examined. Phenolic contents of green and black tea were determined by using enzyme electrodes.

The research described herein is aimed at exploring the thermo-mechanical properties of thiol-ene polymers in bulk form, investigating the ability of thiol-ene polymers to behave desirably as photolithographic media, and providing the first characterization of the mechanical properties of two-photon stereolithography-produced polymer structures. The thiol-ene polymerization reaction itself is well-characterized and described in the literature, but the thermomechanical properties of thiol-ene and thiol-ene/acrylate polymers still require more rigorous study. Understanding the behavior of thiol-ene networks is a crucial step towards their expanded use in bulk form, and particularly in specialized applications such as shape memory devices. Additionally, the thiol-ene polymerization reaction mechanism exhibits unique properties which make these polymers well suited to photolithography, overcoming the typical dichotomy of current materials which either exhibit excellent photolithographic behavior or have controllable properties. Finally, before two-photon stereolithography can create mechanisms and devices which can serve any mechanically functional role, the mechanical properties of the polymers they produce must be quantitatively characterized, which is complicated by the extremely small scale at which these structures are produced. As such, mechanical characterization to date has been strictly qualitative. Fourier transfer infrared spectroscopy revealed functional group conversion information and sol-fraction testing revealed the presence of unconverted monomer and impurities, while dynamic mechanical analysis and tensile testing revealed the thermomechanical responses of the systems. Nanoindentation was employed to characterize the mechanical properties of polymers produced by two-photon stereolithography. Optical and electron microscopy were exploited to provide quantitative and qualitative evaluations of thiol-ene/acrylate performance in small-scale polymerization regimes. The broad objective of the research was to explore thiol-ene polymer behavior both in bulk and at the small scale in an effort to supplement the material library currently used in these fields and to expand the design envelope available to researchers. The significance of the research is the advancement of a more complete and fundamental understanding of thiol-ene polymerization from kinetics to final properties, the quantitative establishment of the mechanical properties of materials created with two-photon stereolithography, and the comprehensive characterization of a supplementary class of photopatternable polymers with greater property tunability than is possible with currently used materials.

Thesis (Ph.D.)--McMaster University, 2005. / Supervisor: John L. Brash. Includes bibliographical references. Also available online.

Thesis (PhD) -- University of Western Sydney, 2002. / "A candidate for the degree of Doctor of Philosophy." "A thesis submitted in the School of Science, Food and Horticulture, University of Western Sydney." "June 2002" Bibliography: leaves 303 - 305.

Thesis (Ph.D.)--University of Wollongong, 2005. / Typescript. Includes bibliographical references.

Thesis (Ph. D.)--Biomedical Engineering, Georgia Institute of Technology, 2008. / Committee Chair: Nie, Shuming; Committee Member: Bao, Gang; Committee Member: Chung, Leland; Committee Member: Murthy, Niren; Committee Member: Prausnitz, Mark.