The measurement of the ratio of the branching fractions of Υ (3S) decays into τ leptons over dimuons (R τ /μ = B(Υ (3S) → τ + τ − )/B(Υ (3S) → μ + μ − )) is a test of lepton universality. A violation of lepton universality would be evidence of new physics (and possibly of a light CP-odd Higgs boson). A sample of Υ (3S) decays (2.408 fb −1 ) collected with the B A B AR detector at the SLAC National Accelerator Laboratory was used to determine that the ratio R τ /μ is R τ /μ = 1.0385 ± 0.034 ± 0.019. Using the remaining blinded data sample (corresponding to an integrated luminosity of 25.6 fb −1 ) the estimated statistical sensitivity will be 1.1 % and the estimated systematic uncertainty of R τ /μ is 1.9 %. Prior to this work, previous measurements of R τ /μ had an estimated total precision of 10 %. / Graduate

This thesis presents a whole-core benchmark of the European Pressurized Reactor (EPR) using multiple transport methods. The core specifications were taken directly from the Final Safety Analysis Report (FSAR) submitted to the Nuclear Regulatory Commission (NRC) and the reactor was modeled in a stylized manner while maintaining full heterogeneity at the pin and assembly level. The geometry and material specifications are given as well as problem-specific cross sections for 2, 4, and 8 energy group calculations. Cross sections were generated using HELIOS, a lattice depletion code based on the Collision Probability Method (CPM). The multi-group cross sections were utilized in the reference calculation, COMET calculation, and response function generation. The reference solution was obtained via an MCNP model identical to the one implemented in COMET. Specific steps towards constructing and running a COMET calculation are outlined. Detailed results including assembly eigenvalues, core eigenvalues, and pin fission densities are presented.

The reported lifetime in an in-beam neutron lifetime experiment performed at NIST was tn = (886.3 ± 3.4) s. The largest source of uncertainty was the efficiency of the neutron flux monitor (0.3% relative uncertainty). The flux monitor operates by counting charged particles produced when neutrons impinge on a 6Li foil. Its efficiency was calculated from the 6Li thermal neutron cross section, the solid angle subtended by the charged particle detectors, and the amount of neutron-absorbing material present on the foil. An absolute black neutron detector for cold neutron beams has been developed to measure the efficiency without the need to know these quantities. The flux monitor efficiency is measured to a precision of 0.052% using this direct calibration technique. This calibration removes the largest barrier to a 1 s neutron lifetime measurement with the beam technique. It is hoped that this data can also be used to re-evaluate the current NIST neutron lifetime value, reduce its uncertainty, and remove the dependence on evaluated nuclear data files. There is also the possibility for a direct measurement of the 6Li thermal neutron cross section.

In zukünftigen kerntechnischen Anlagen können die Materialien Blei und Bismut eine größere Rolle spielen als heute. Für die Planung dieser Anlagen werden verlässliche Wirkungsquerschnittsdaten benötigt. Insbesondere der Neutronentransport in einem Blei-Spallationstarget eines beschleunigergetriebenen unterkritischen Reaktors hängt stark von den inelastischen Streuquerschnitten im Energiebereich von 0,5 MeV bis 6 MeV ab. In den vergangenen 20 Jahren wurden elastische und inelastische Neutronenstreuquerschnitte mit hoher Präzision für eine Vielzahl von Elementen am PTB-Flugzeitspektrometer gemessen. Zur Erzeugung der Neutronen wurde hauptsächlich die D(d,n)-Reaktion genutzt. Aufgrund des Q-Wertes der Reaktion und der verfügbaren Deuteronenenergien können Neutronen im Energiebereich von 6 MeV bis 16 MeV erzeugt werden. Die Messung von Wirkungsquerschnitten bei niedrigeren Energien erfordert somit die Verwendung einer anderen neutronenerzeugenden Reaktion. Hierfür wurde die 15N(p,n)15O-Reaktion ausgewählt, da sie die Erzeugung monoenergetischer Neutronen bis zu einer Energie von 5,7 MeV erlaubt. In dieser Arbeit wird die 15N(p,n)-Reaktion auf ihre Eignung als Quelle monoenergetischer Neutronen in Streuexperimenten untersucht. Die Untersuchung der Reaktion beinhaltet die Messung von differentiellen Wirkungsquerschnitten für ausgewählte Energien und die Auswahl von optimalen Targetbedingungen. Differentielle elastische und inelastische Neutronenstreuquerschnitte wurden unter Anwendung der Flugzeitmethode für Blei bei vier Energien zwischen 2 MeV und 4 MeV gemessen. Eine Bleiprobe mit natürlicher Isotopenzusammensetzung wurde verwendet. Für den Nachweis der gestreuten Neutronen wurden NE213 Flüssigszintillatoren verwendet, deren Nachweiswahrscheinlichkeit gut bekannt ist. Winkelintegrierte Wirkungsquerschnitte wurden mit einem Legendre-Polynomfit unter Verwendung der Methode der kleinsten Quadrate bestimmt. Zusätzlich erfolgten Messungen für die isotopenreinen Streuproben 209Bi und 181Ta bei 4 MeV Neutronenenergie. Die Ergebnisse werden mit denen früherer Experimente und aktuellen Evaluationen verglichen. / In future nuclear facilities, the materials lead and bismuth can play a more important role than in today’s nuclear reactors. Reliable cross section data are required for the design of those facilities. In particular the neutron transport in the lead spallation target of an Accelerator-Driven Subcritical Reactor strongly depends on the inelastic neutron scattering cross sections in the energy region from 0.5MeV to 6 MeV. In the recent 20 years, elastic and inelastic neutron scattering cross sections were measured with high precision for a variety of elements at the PTB time-of-flight spectrometer. The D(d,n) reaction was primarily used for the production of neutrons. Because of the Q value of the reaction and the available deuteron energies, neutrons in the energy range from 6MeV to 16MeV can be produced. For the cross section measurement at lower energies, however, another neutron producing reaction is required. The 15N(p,n)15O reaction was chosen, as it allows the production of monoenergetic neutrons with up to 5.7MeV energy. In this work, the 15N(p,n) reaction was studied with focus on the suitability as a source for monoenergetic neutrons in scattering experiments. This includes the measurement of differential cross sections for the neutron producing reaction and the choice of optimum target conditions. Differential elastic and inelastic neutron scattering cross sections were measured for lead at four energies in the region from 2MeV to 4MeV incident neutron energy using the time-offlight technique. A lead sample with natural isotopic composition was used. NE213 liquid scintillation detectors with well-known detection efficiencies were used for the detection of the scattered neutrons. Angle-integrated cross sections were determined by a Legendre polynomial expansion using least-squares methods. Additionally, measurements were carried out for isotopically pure 209Bi and 181Ta samples at 4MeV incident neutron energy. Results are compared with other measurements and recent evaluations.

Thesis (M.S.)--Miami University, Dept. of Physics, 2008. / Title from first page of PDF document. Includes bibliographical references (p. 39-40).

Thesis (M.S.)--Miami University, Dept. of Physics, 2008. / Title from first page of PDF document. Includes bibliographical references (p. 36-37).

Thesis--University of California, Berkeley. / Includes bibliographical references (p. 57). 23

abstract: Microchannel heat sinks can possess heat transfer characteristics unavailable in conventional heat exchangers; such sinks offer compact solutions to otherwise intractable thermal management problems, notably in small-scale electronics cooling. Flow boiling in microchannels allows a very high heat transfer rate, but is bounded by the critical heat flux (CHF). This thesis presents a theoretical-numerical study of a method to improve the heat rejection capability of a microchannel heat sink via expansion of the channel cross-section along the flow direction. The thermodynamic quality of the refrigerant increases during flow boiling, decreasing the density of the bulk coolant as it flows. This may effect pressure fluctuations in the channels, leading to nonuniform heat transfer and local dryout in regions exceeding CHF. This undesirable phenomenon is counteracted by permitting the cross-section of the microchannel to increase along the direction of flow, allowing more volume for the vapor. Governing equations are derived from a control-volume analysis of a single heated rectangular microchannel; the cross-section is allowed to expand in width and height. The resulting differential equations are solved numerically for a variety of channel expansion profiles and numbers of channels. The refrigerant is R-134a and channel parameters are based on a physical test bed in a related experiment. Significant improvement in CHF is possible with moderate area expansion. Minimal additional manufacturing costs could yield major gains in the utility of microchannel heat sinks. An optimum expansion rate occurred in certain cases, and alterations in the channel width are, in general, more effective at improving CHF than alterations in the channel height. Modest expansion in height enables small width expansions to be very effective. / Dissertation/Thesis / M.S. Mechanical Engineering 2011

Title: Monte Carlo Simulations of the Tile Calorimeter and Measurement of the Z → ττ Cross Section with the ATLAS Detector Author: Mgr. Jana Nováková Department: Institute of Particle and Nuclear Physics (IPNP) Supervisor: RNDr. Tomáš Davídek, PhD., IPNP Supervisor's e-mail address: davidek@ipnp.troja.mff.cuni.cz Abstract: The Monte Carlo simulations of the Tile calorimeter in the ATLAS experiment at the LHC, especially the electronic noise and multiple interactions (co-called pile-up), are discussed in the thesis. A good agreement in the cell energy distribution between data and Monte Carlo simulations is found. The cross section measurement of Z → ττ events with the ττ invariant mass between 66 and 116 GeV with the ATLAS experiment is described in the next part of the thesis. Data samples collected during 2011 corresponding to the integrated luminosity of 1.34 - 1.55 fb−1 are used for the analysis. The measurements are performed in three different final states depending on the decay mode of the τ leptons. The measurement in the channel with one τ lepton decaying leptonically into the electron + neutrinos (schematically τ → e + νe + ντ ) and the other one hadronically (schematically τ → hadrons + ντ ), especially the calculation of the nominal cross section and the evaluation of the systematic...

Contemporary transformation of the Czech primary educational system is characterized according to RVP ZV. The thesis deal with cohesion of the RVP ZV and ethic aspects. The author focuses on ethic education as a complementary educional branche and surveys approaches of individual teachers to this curriculum. The theoretical part explains basic ideas such as ethic, curriculum and section themes. The work acquaints with the ethic education, its aims, methods and its representation in the curriculum. In the practical part are analysed the statements of respondents and compared the approaches of pedagogues to the own realised curriculum with the ethic aspects. The aim of work is to discover, whether the ethic education is involved in the teaching and how the teachers approach to this education.