This thesis presents a novel modulation scheme, called feedback dithering modulation, for DC to AC power converters. The feedback dithering modulator consists of a quantizer and a recently reported feedback dithering circuit, performing multilevel modulation with improved linearity and signal quality as opposed to the conventional modulation schemes. By combining the feedback dithering modulation and optimal control, a single-phase DC to AC power converter is built and tested. The resulting total harmonic distortion can be as low as 0.38% for a 25£[ load, or 0.47% when the output is open. Under the various operating conditions with DC voltages source varying from 190 V to 300 V and output powers from 0 to 600 W, the power converter always maintains a total harmonic distortion less than 1%, exhibiting high performance and excellent robustness.

This thesis applies digital repetitive control to a single-phase DC-to-AC converter, with some proposed designs to improve stability and enhance performance of the converter under various load variations. A practical DC-to-AC converter is required to convert DC power to stable AC power with low harmonic distortion when attached to various linear or nonlinear loads. This thesis combines repetitive control with feedback dithering modulation and optimal state feedback to control the converter. The repetitive control is responsible for regulating output power and eliminating harmonics, while the feedback dithering modulation for switching the power transistors with reduced switching noise and the state feedback for stabilizing the converter under various load variations. The presented control and modulation schemes of the power converter are implemented on an FPGA (Field Programmable Gate Array). The experiments confirm the excellent performance and robustness of the converter, indicating a total harmonic distortion of less than 0.5% for the converter when attached to various linear or nonlinear loads.

Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: The development of fast and efficient processors, programmable devices and high power semiconductors has led to the increased use of semiconductors directly in the power supply path in order to achieve strict power quality standards. New and advanced algorithms are used in the process and calculated on-line to bring about the required fast response to voltage variations. Losses in high voltage semiconductors increase with increased operating frequencies. A balance between semiconductor power losses and power quality is achieved through control of power semiconductor switching frequencies. A predictive control algorithm to achieve high power quality and limit the power losses in the high power semiconductor switches through switching frequency control is discussed for a tap switched voltage regulator. The quality of power, voltage regulator topology and the control algorithm are discussed. Simulation results of output voltage and current are shown when the control algorithm is used to control the regulator. These results are verified by practical measurements on a synchronous buck converter. / AFRIKAANSE OPSOMMING: Die ontwikkeling van vinnige en doeltreffende verwerkers, programmeerbare toestelle en hoëdrywings halfgeleiers het gelei tot 'n groter gebruik van halfgeleiers direk in die kragtoevoer pad om streng elektriese toevoer kwaliteit standaarde te bereik. Nuwe en gevorderde algoritmes word gebruik in die proses en word aan-lyn bereken om die nodige vinnige reaksie tot spanningswisselinge te gee. Verliese in hoë-spannings halfgeleiers verhoog met hoër skakel frekwensies. 'n Balans tussen die halfgeleier drywingsverliese en spanningskwalteit is behaal deur die skakel frekwensie in ag te neem in die beheer. 'n Voorspellinde-beheer algoritme om ‘n hoë toevoerkwaliteit te bereik en die drywingsverliese in die hoëdrywingshalfgeleier te beperk, deur skakel frekwensie te beheer, is bespreek vir 'n tap-geskakelde spanning reguleerder. Die toevoerkwaliteit, spanningsreguleerder topologie en die beheer algoritme word bespreek. Simulasie resultate van die uittree-spanning en stroom word getoon wanneer die beheer algoritme gebruik word om die omsetter te beheer. Hierdie resultate is deur praktiese metings op 'n sinkrone afkapper.

Submitted by Alex de Sá Martins null (lex.martins@hotmail.com) on 2017-12-16T23:31:27Z No. of bitstreams: 1 ANÁLISE E PROJETO DO CONVERSOR FONTE-Y PARA USO....pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) / Approved for entry into archive by Maria Marlene Zaniboni null (zaniboni@bauru.unesp.br) on 2017-12-18T12:51:16Z (GMT) No. of bitstreams: 1 martins_as_me_bauru.pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) / Made available in DSpace on 2017-12-18T12:51:16Z (GMT). No. of bitstreams: 1 martins_as_me_bauru.pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) Previous issue date: 2017-10-26 / Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) / Este trabalho aborda o estudo de topologia de conversor de energia baseada no uso de configuração de rede de impedância denominada fonte-Y, com o objetivo de ser aplicado em sistemas de geração distribuída de energia, em redes de baixa tensão. Em sistemas de geração distribuída de energia usualmente se faz necessária a existência de um estágio elevador de tensão e um estágio inversor, ambos controlados para produzir tensão e/ou corrente senoidal com mesma frequência, amplitude e fase da rede elétrica. Nesse sentido, este trabalho propõe a aplicação do conversor fonte- Y entre a geração e a conexão com e rede elétrica, de forma que as ações de conversão relacionadas com a elevação (CC-CC) e inversão (CC-CA) sejam efetuadas de forma integrada por uma única estrutura, contribuindo com a possibilidade de melhoria no rendimento global devido à minimização de estágios de conversão em cascata. Inicialmente, é efetuado um levantamento bibliográfico relacionando as principais topologias de conversores utilizando redes de impedância com indutores acoplados, considerando os aspectos operacionais, arranjo de impedância e ganho estático idealizado, desprezando perdas entre tensão de entrada e tensão máxima de saída obtida. Segue-se o estudo da operação de conversor CCCC empregando rede de impedância do tipo Y, definição das equações que regem o comportamento no tempo das tensões e correntes nos capacitores e indutores. É feita uma avaliação comparativa do ganho estático de tensão obtido e dos esforços nos semicondutores em função das variáveis de controle de projeto e operação disponíveis. Prossegue-se com o estudo da operação do conversor CC-CA empregando rede de impedância do tipo Y, considerando extensão das expressões encontradas para a operação como conversor CC-CC. Por fim, simulações computacionais foram desenvolvidas no ambiente PSIM contemplando o emprego dos circuitos e estratégias de modulação relacionadas com aplicações do conversor fonte- Y, em operação CC-CC e operação CC-CA visando a integração em sistemas de geração de energia, para demonstrar as vantagens e desvantagens do uso dessa topologia. / This paper deals with the study of energy converter topology based on the use of impedance network configuration called Y-source, with the objective of being applied in photovoltaic energy cogeneration systems in low voltage grids. In photovoltaic energy generation systems, it is usually necessary to have a voltage boost stage and an inverter stage, both controlled to produce voltage and / or sine current with the same frequency, amplitude and phase of the power grid. In this sense, this work proposes the application of the Y-source converter between the photovoltaic generation and the connection with the electric grid, so that the conversion actions related to elevation (DC-DC) and inversion (DC-AC) in a way integrated by a single structure, contributing to the possibility of improvement in the overall yield due to the minimization of cascade conversion stages. Initially a bibliographical survey was performed relating the main inverter topologies using impedance networks with coupled inductors considering the operational aspects, impedance arrangement and ideal static gain between the input voltage and the maximum output obtained. ext, the study of the DC-DC converter operation using the Y-type impedance network, definition of the equations governing the time behavior of the voltages and currents in the capacitors and inductors, is presented. It is also done the comparative evaluation of the static voltage gain obtained and the stresses in the semiconductors according to the available control and design control variables. Study of the operation of the DC-AC converter employing type Y impedance network, considering the extension of the expressions found for the operation as DC-DC converter. Finally, computational simulations were developed in the PSIM environment, considering the use of circuits and modulation strategies related to Y-source converter applications, in DC-DC operation and DC-AC operation for integration into power cogeneration systems, to demonstrate advantages and disadvantages of using this topology. / 134173/2017-1