Non-wetting surfaces offer enhanced capabilities over bare metal substrates for condensation with or without phase change. This trait can be utilized to broaden strategies in combating water scarcity in water stressed areas. Slippery lubricant infused surfaces have the ability to shed water droplets with lower nucleation times, taking advantage of more of the limited amount of time available to collect dew and fog than traditional surfaces. However, existing studies focus on short durations with scant information available on the longer-term performance or durability of the materials in application environments. To address this knowledge gap, dew harvesting studies were conducted over a 96 hour period on a lubricant infused surface vis-à-vis regular surface of the same material. Three phases of performance are identified and discussed with regard to the water harvesting potential. The second part of the thesis addresses water condensation under conditions where freezing is a potential issue. Non-wetting surfaces have been shown to be a promising method of limiting the formation of ice from sessile droplets. This study explores the effect of surface roughness on the freeze time of sessile water droplets. Superhydrophobic and hydrophobic, lubricant infused, copper surfaces were created via electrodeposition and chemical etching in conjunction with chemical treatments to achieve non-wetting surfaces of varying surface textures. Freezing characteristics on the surfaces are studied experimentally and, for the first time, computationally, wherein the surface is described using a fractal surface topography. The effect of surface engineering on the freezing dynamics and comparison between the experimental and the computational studies are elucidated. / Master of Science / The use of durable, water repelling surfaces that are also thermally conductive provide an opportunity to help alleviate strain from a growing world crisis, water scarcity. Lubricant infused surfaces shed water from their surface by providing a slippery layer for the droplets to slide on, as opposed to bare metal which water tends to cling to. This behavior makes lubricant infused surfaces attractive as a water harvesting method. However, these surfaces degrade over time and must be maintained to perform at their maximum capability, collecting water for 40 minutes more than a bare surface. This thesis focuses on the performance of these surfaces over a 96-hour operating period to characterize the effect lubricant drainage has on the water collection behavior. Freezing water droplets, commonly referred to as icing, poses concerns for safety and operational ability in industries like renewable energy generation, where icing limits efficiency. Non-wetting surfaces have a unique ability to inherently slow down the phase change of a water droplet to ice due to the lower contact area of droplets resting on the surface. This thesis examines superhydrophobic and lubricant infused surfaces of varying degrees of roughness to explore the effect that the contact angle and different surface structures have on the freezing rate of water on the surface. The experimental results are compared to numerical simulations, which is useful in designing systems that would implement this passive icing mitigation technique.

The wettability and phase change phenomena of water are ubiquitous on biological and artificial surfaces. Properties like water repellency, self-cleaning, coalescence induced condensation jumping, anti-frosting, and dew harvesting arise on surfaces with particular structures and chemistry and are of particular interest for energy and water saving. This thesis collects different studies of wettability and phase change on natural and artificial surfaces: growth and self-ejection of condensation droplets on micro and nanostructured surfaces we fabricated, their applications, the Sliding on Frost of condensation droplets observed on the Cotinus Coggygria leaf, the dew harvesting property of the Old Man of the Andes Cactus enhanced by distance coalescence through microgrooves and finally, a theoretical study of viruses viability in sessile droplets. The first chapter introduces the theoretical framework of wettability and phase changes on surfaces. In the second chapter, we present the self-ejection of condensation droplets from hydrophobic nanostructured microstructures. We modelled analytically the droplets jumping and fabricated surfaces to verify the predictions. The fabricated geometry was inspired by the modelling and the available fabrication techniques. We tested the surfaces in condensation conditions. Using a high frame rate camera coupled with a long working distance microscopy objective, we investigated the growth and ejection transient. We then compared the experimental self-ejection velocity for various structures geometry with our analytical models. In Chapter 3, we investigated the applications of the fabricated surfaces reported in Chapter 2. In Chapter 4, we explore the condensation frosting on the leaf of Cotinus Coggygria, native of our woods and with interesting hydrophobic properties. Covered by wax nanotubules, it exhibits coalescence-induced condensation jumpings that may be a useful cleaning tool. Furthermore, the frost is delayed but not only for the jumping. Surprisingly, at temperatures some degrees below zero, we observed what we called ‘droplet Sliding on Frost bridges’, that further delays frosting. We described the feasibility of this sliding in terms of dynamic contact angles of the surface and contact angles of supercooled water on ice. By capturing high temporal and spatial resolution videos we investigated the sliding on frost and droplet recalescence (fast dendrite growth that partially solidify the liquid). The responsible for the failure of sliding for temperatures from about -8 ° C down appears to be the advancing angle of water on ice that increases with the subcooling rather than the recalescence that blocks the drop in place. These results add a piece to the fundamental research on the supercooled water-ice-vapour interfaces. As it often happens, biological surfaces offer a starting point for the study of fundamental mechanisms and the development of artificial surfaces with optimized properties. In the Chapter 5, the multifunctional roles of hairs and spines in Old Man of the Andes Cactus (Oreocereus trolli) are studied. We study the morphology of the appendages, the hairs wettability, mechanical properties of both, and the dew formation on spines. The longitudinal microgrooves on the spines cause a particular phenomenon of distant coalescence (DC), in which smaller droplets flow totally or partially into larger ones through the microgrooves, with consequent accumulation of water in a few large drops. An earlier study has shown artificial micro-grooved surfaces that exhibit DC are more efficient than flat ones at collecting and sliding dew, and thus these cactus spines could act as soil dew conveyors. The agreement between our analytical model and experimental data verifies that the flow is driven by the Laplace pressure difference between the drops. This allowed us to obtain a general criterion for predicting the total or partial emptying of the smaller drops as a function of the dynamic contact angles of a surface. Based on this criterion, an hydrophilic material with small contact angle hysteresis would allow a greater number of complete drops emptying. The COVID-19 pandemic has raised the problem of contagion from airborne and deposited droplets. In the last chapter, we report the state of the art of experiments on the viability of viruses in deposited droplets. Up to date, it has been experimentally highlighted that the relative viability of some viruses (RV) depends on the material chemistry, temperature, and interestingly, on relative humidity (RH) with a U-shaped trend. One of the current hypotheses is that the cumulative dose of salt concentration (CD) affects RV. We model the RV of viruses in sessile droplets by inserting a RV-CD relation in a model of droplet evaporation. By considering a saline water droplet (one salt) as the simplest approximation of real solutions, we analytically simulate the time evolution of salt concentration, vapor pressure, and droplet volume varying contact angles, droplet sizes, and RH in the range 0–100%. The results elucidate some previously not yet well-understood dynamics, demonstrating how three main regimes—directly implicated in nontrivial experimental trends of virus RV—can be recognized as the function of RH. The proposed approach could suggest a chart of a virus fate by predicting its survival time at a given temperature as a function of RH and contact angle. We found a good agreement with experimental data for various enveloped viruses and predicted in particular for the Phi6 virus, a surrogate of coronavirus, the characteristic U-shaped dependence of RV on RH. Given the generality of the model, once experimental data are available that link the vulnerability of a certain virus (such as SARS-CoV-2) to the concentrations of salts or other substances in terms of CD, it is envisioned that this approach could be employed for antivirus strategies and protocols for the prediction/reduction of human health risks associated with SARS-CoV-2 and other viruses.