Made available in DSpace on 2014-12-17T15:42:14Z (GMT). No. of bitstreams: 1 MarciaSL_TESE.pdf: 4842135 bytes, checksum: b5c017ecd503f8ac8f797fb07359e645 (MD5) Previous issue date: 2011-06-28 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / The alginates are copolymers of 1→4-linked β-D-mannuronic acid (M) and α-Lguluronic acid (G) residues that are arranjed in a block structure along a linear chain. Titanium dioxide, TiO2, is a ceramic material and can exist in three distinct crystallography forms: anatase, brookite and rutile. composites of organic and inorganic materials have better properties than the components alone. Thus, this study aims to synthesize, characterize and analyze the composite NaAlg-TiO2 in the form of powder and film. The synthesis of composite powders was performed using the sol-gel process and obtain the composite film was performed using the slow evaporation process, then the composites were analyzed by infrared spectroscopy, fluorescence x ray, thermal analysis, attenuated total reflection (ATR), x ray diffraction and impedance spectroscopy. The X ray diffraction patterns of composite powders show that with increasing calcination temperature, there were no complete transition of rutile-anatase crystalline phase, since at all temperatures studied (300, 500, 700, 900 and 1100?C) were observed peaks of anatase phase. Thermal analysis shows that at 400?C caused the decomposition of sodium alginate in sodium carbonate and above 600?C, we observe an exothermic peak related to the decomposition of sodium carbonate and in the presence of titanium dioxide becomes sodium titanate. The XRD results confirm the formation of sodium carbonate at 700?C and the formation sodium titanate in the temperature range 900-1100?C. The sodium titanate influenced the electrical properties of the material, because with increasing temperature there was a decrease in conductivity, probably due to the creation of Ti vacancies, since the sodium can induce the reduction of surface Ti4+ ions into Ti3+ species. The infrared spectra of the composites in the form of powder and film showed a small shift in the bands compared to the spectrum of pure alginate, indicating that these shifts, even small ones, have evidence of miscibility between the polymer and ceramic material / O alginato de s?dio, NaAlg, ? um polissacar?deo formado por liga??es do tipo 1-4 entre os ?cidos β-D-manur?nico e α-L-gulur?nico arranjados em bloco ao longo de uma cadeia linear. O di?xido de tit?nio, TiO2, ? um material cer?mico e existe em tr?s formas cristalinas: anat?sio, bruquita e rutilo. Os comp?sitos de materiais org?nicos e inorg?nicos apresentam melhores propriedades do que os componentes isoladamente. Dessa forma, o presente trabalho teve objetivo sintetizar, caracterizar e analisar os comp?sitos, NaAlg-TiO2, em formas de p? e de membrana. A s?ntese dos p?s comp?sitos foi realizada atrav?s do processo sol-gel e a obten??o dos comp?sitos em forma de membrana foi realizada atrav?s do processo de evapora??o lenta. Em seguida, os comp?sitos foram caracterizados por espectroscopia de infravermelho, difratometria de raios X, espectroscopia de imped?ncia, fluoresc?ncia de raios X, an?lise t?rmica e espectroscopia de reflect?ncia total atenuada-ATR. Os difratogramas de raios X dos p?s comp?sitos mostraram que, com o aumento da temperatura de calcina??o, n?o houve a completa transi??o de fase anat?sio-rutilo, uma vez que, em todas as temperaturas estudadas (300, 500, 700, 900 e 1100?C) foram observados picos da fase anat?sio. A an?lise t?rmica mostrou que em 400?C ocorreu ? decomposi??o do alginato de s?dio em carbonato de s?dio e, acima de 600?C, se observa um pico exot?rmico referente ? decomposi??o do carbonato de s?dio que, na presen?a do di?xido de tit?nio, transforma-se em titanato de s?dio, confirmados, tamb?m, atrav?s dos difratogramas de raios X, em que na temperatura de 700?C observa-se picos referentes ao carbonato de s?dio e em 900 e 1100?C picos relacionados ao titanato de s?dio. O titanato de s?dio influenciou nas propriedades el?tricas do material, pois com o aumento da temperatura houve um decr?scimo na condutividade, provavelmente, devido ? cria??o de vac?ncias de Ti, uma vez que, o Na+ induz a redu??o dos ?ons Ti+4 para esp?cies Ti+3. Os espectros de infravermelho dos comp?sitos em formas de p? e de membrana mostraram um pequeno deslocamento nas bandas, quando comparados ao espectro do alginato de s?dio puro, indicando que estes deslocamentos, mesmo que pequenos, t?m ind?cios de miscibilidade entre o pol?mero e o material cer?mico

Submitted by Automa??o e Estat?stica (sst@bczm.ufrn.br) on 2016-05-10T21:07:58Z No. of bitstreams: 1 BrennoHenriqueSilvaFelipe_DISSERT.pdf: 3323797 bytes, checksum: c0441882551b254732cc3dec33b910be (MD5) / Approved for entry into archive by Arlan Eloi Leite Silva (eloihistoriador@yahoo.com.br) on 2016-05-12T22:52:21Z (GMT) No. of bitstreams: 1 BrennoHenriqueSilvaFelipe_DISSERT.pdf: 3323797 bytes, checksum: c0441882551b254732cc3dec33b910be (MD5) / Made available in DSpace on 2016-05-12T22:52:21Z (GMT). No. of bitstreams: 1 BrennoHenriqueSilvaFelipe_DISSERT.pdf: 3323797 bytes, checksum: c0441882551b254732cc3dec33b910be (MD5) Previous issue date: 2015-02-19 / Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico (CNPq) / O presente projeto visa a s?ntese e caracteriza??o de um nanorevestimento de di?xido de tit?nio dopado com prata em tecido de poli?ster arom?tico, a fim de desenvolver um material t?xtil funcional com aplica??oself-cleaning. Uma t?cnica de deposi??o f?sica de vapor (PVD) foi utilizada como m?todo de s?ntese. A sele??o do material suporte e a t?cnica utilizada na obten??o dos nanorevestimentos s?o vari?veis que podem influenciar nas suas propriedades funcionais, homogeneidade e ades?o. As fibras t?xteis s?o materiais muito empregados como substrato por possu?rem uma maior flexibilidade, serem facilmente adapt?veis a qualquer geometria e baixo custo. A presen?a de Ag e TiO2, bem como sua cristalinidade, foi comprovada atrav?s das an?lises de difra??o de raios X (DRX), espectroscopia fotoeletr?nica de raios-X (XPS) e fluoresc?ncia de raios-x (FRX). A morfologia de superf?cie foi avaliada atrav?s das t?cnicas de microscopia de for?a at?mica (AFM) e microscopia eletr?nica de varredura (MEV). A efici?ncia da atividade fotocatal?tica do material foi comprovada pela descolora??o do corante acid blue 113 em meio a fontes de radia??o UV, com uso da t?cnica de espectroscopia de absor??o (96%). A degrada??o da mol?cula do corante acid blue 113 foi confirmada atrav?s da t?cnica de espectroscopia de infravermelho por transformada de Fourier (FTIR). O car?ter hidrof?bico do nanorevestimento foi confirmado atrav?s da t?cnica de medida de ?ngulo de contato. O car?ter anti UV foi confirmado foi confirmado de acordo com a metodologia normativa AS/NZS 4399:1996. Os resultados comprovam que o material desenvolvido apresenta uma alta capacidade autolimpante, bem como protetora UV. / Innovative methods in the textile segment is currently responsible for increase in production processes, development of new materials and add new technologies in an area that was one of the major participants in the industry revolution. Thus, much research has been responsible for putting the textile industry in the new era of technological revolution watching so, the dynamism of microelectronics companies, food, and mechanics, among others. To this end, this PhD project aims to add value research involving new textile materials. Thus, this project aims to make the synthesis and characterization of a silver doped titanium dioxide nanocoating on polyester fabric in order to develop a functional textile material with self-cleaning application. A physical vapor deposition technique (PVD) was used as the method of synthesis. The selection of the support material and the technique used in obtaining the nanocoatings are variables that can influence their functional properties, uniformity and adhesion. The textile fibers are materials used as substrate by having greater flexibility to be easily adaptable to any geometry and low cost. The efficiency of the photocatalytic activity of the material was confirmed by discoloration of the dye Acid Blue 113 through UV radiation sources, using absorption spectroscopy (96%). The presence of Ag and TiO2 was confirmed by analysis of X-ray diffraction (XRD) photoelectron spectroscopy X-ray (XPS) and x-ray fluorescence (XRF). The surface morphology was evaluated through the techniques of atomic force microscopy (AFM) and scanning electron microscopy (SEM). Degradation of Acid Blue 113 dye molecule was confirmed by infrared spectroscopy Fourier transform (FTIR). The hydrophobic character of nanocoating was confirmed by contact angle measurement technique. The results show that the developed material has a high capacity self-cleaning pro perties

Made available in DSpace on 2014-12-17T14:16:22Z (GMT). No. of bitstreams: 1 LucianaRS_Pre_textuais.pdf: 37160 bytes, checksum: 5c10ca3517f836e974edc672ecd286cb (MD5) Previous issue date: 2008-02-12 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / The inorganic actives, represented mainly by microfine zinc oxide and titanium dioxide, have shown great potential to protect against large UV spectrum. The aim of this study is the development, characterization and analysis of stability in the short term of microemulsions containing inorganic fotoprotection agents. The microemulsions identified by the phases diagram containing the metallic oxides were produced by two different methods and subjected to the centrifugation test and thermal stress cycles, and subsequently characterized by macroscopic evaluation, test dilution, electrical conductivity, pH, particle size, and zeta potential. This study highlights the influence of the metal oxides addition in the structure and distribution of micelles in the microemulsions / Os agentes fotoprotetores inorg?nicos, representados principalmente pelo ?xido de zinco e di?xido de tit?nio microfinos, t?m mostrado grande potencial de prote??o contra amplo espectro de radia??o UV. O objetivo deste trabalho consiste no desenvolvimento, caracteriza??o e estudo de estabilidade a curto termo de microemuls?es contendo agentes fotoprotetores inorg?nicos. As microemuls?es identificadas pelo diagrama de fases e adicionadas dos ativos fotoprotetores foram elaboradas a partir de dois m?todos diferentes e submetidas ao teste de centrifuga??o e ciclos gelo-degelo, sendo posteriormente caracterizadas pela avalia??o macrosc?pica, teste de dilui??o, condutividade el?trica, pH, granulometria e determina??o de potencial zeta. Este estudo evidencia a influ?ncia da adi??o dos ?xidos met?licos na estrutura??o micelar e distribui??o de tamanho de part?culas das microemuls?es

Made available in DSpace on 2014-12-17T14:58:13Z (GMT). No. of bitstreams: 1 RaquelGC_DISSERT.pdf: 1617455 bytes, checksum: fe137c67d61e0483bac922261c815e1e (MD5) Previous issue date: 2011-11-23 / Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico / In this study we used the plasma as a source of energy in the process of carbothermic reduction of rutile ore (TiO2). The rutile and graphite powders were milled for 15 h and placed in a hollow cathode discharge produced by in order to obtain titanium carbonitride directly from the reaction, was verified the influence of processing parameters of plasma temperature and time in the synthesis of TiCN. The reaction was carried out at 600, 700 and 800˚C for 3 to 4 hours in an atmosphere of nitrogen and argon. During all reactions was monitored by plasma technique of optical emission spectroscopy (EEO) to check the active species present in the process of carbothermal reduction of TiO2. The powder obtained after the reactions were characterized by the techniques of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The technique of EEO were detected in all reactions the spectra CO and NO, and these gas-phase resulting from the reduction of TiO2. The results of X-ray diffraction confirmed the reduction, where for all conditions studied there was evidence of early reduction of TiO2 through the emergence of intermediate oxides. In the samples reduced at 600 and 700˚C, there was only the phase Ti6O11, those reduced to 800˚C appeared Ti5O9 phases, and Ti6O11 Ti7O13, confirming that the carbothermal reduction in plasma, a reduction of the ore rutile (TiO2) in a series of intermediate titanium oxide (TinO2n-1) where n varies between 5 and 10 / Neste trabalho foi utilizado o plasma como fonte energ?tica no processo de redu??o carbot?rmica do min?rio rutilo (TiO2). Os p?s de rutilo e grafite foram mo?dos durante 15 h e introduzidos numa descarga produzida por c?todo oco a fim de obter carbonitreto de tit?nio diretamente da rea??o, sendo verificado a influ?ncia dos par?metros de processamento de plasma, temperatura e tempo na s?ntese de TiCN. As rea??o foram efetuadas a 600, 700 e 800˚C por 3 e 4 horas numa atmosfera de nitrog?nio e arg?nio. Durante todas as rea??es o plasma foi monitorado pela t?cnica de espectroscopia de emiss?o ?ptica (EEO) para verificar as esp?cies ativas presente no processo de redu??o carbot?rmica de TiO2. Os p?s obtidos ap?s as rea??es foram caracterizados pelas t?cnicas de difra??o de raios X (DRX) e microscopia eletr?nica de varredura (MEV). Pela t?cnica de EEO foram detectados em todas as rea??es os espectros CO e NO, sendo essas fases gasosas resultante da redu??o do TiO2. Os resultados de difra??o de raios X confirmou essa redu??o, onde para todas as condi??es estudadas houve evid?ncia de in?cio da redu??o do TiO2 atrav?s do aparecimento de ?xidos intermedi?rios. Nas amostras reduzidas a 600 e 700˚C observou-se apenas a fase Ti6O11, naquelas reduzidas a 800 ˚C apareceram as fases Ti5O9, Ti6O11 e Ti7O13, comprovando que com a redu??o carbot?rmica em plasma, houve redu??o do min?rio rutilo (TiO2) em uma s?rie de ?xido intermedi?rios de tit?nio (TinO2n-1) onde n varia entre 5 e 10

Made available in DSpace on 2014-12-17T15:41:57Z (GMT). No. of bitstreams: 1 RobertaPMM_DISSERT.pdf: 3172444 bytes, checksum: 159d519d0473cdce848696ecb3f8e8f6 (MD5) Previous issue date: 2011-02-24 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / Hybrid systems formed from polymers and transition metals have now their physical and chemical properties extensively investigated for use in electronic devices. In this work, Titanium Dioxide (TiO2) from the precursor of titanium tetrabutoxide and the composite system Poly(Ethylene Glycol)-Titanium Dioxide (TiO2-PEG) were synthesized by sol-gel method. The PEG as acquired and TiO2 and composites powders were analyzed by X-Ray Diffraction (XRD), Spectroscopy in the Infrared region with Fourier transform (IRFT), Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM) and Electrochemical Impedance Spectroscopy (EIS). In the XRD analysis were observed in the TiO2 crystal faces of one of its polymorphs - anatase phase, crystal planes in Poly (Ethylene Glycol) with considerable intensity and in the composite systems the mixture of crystal faces of their precursors isolated and reduction of crystallinity. The TG / DTG suggested increasing the thermal instability of PEG in the composite powders as TiO2 is incorporated into the system. Spectral analysis presented in the infrared overlapping bands for the polymer and metal oxide, reducing the intensity of symmetric stretching of ligand groups in the main chain polymer and angular deformations; were observed using SEM micrographs of the morphological changes suffered by composite systems with the variation of the oxide concentration. Analyses by impedance spectroscopy indicated that the increased conductivity in composite occurs in line with the addition of the metal oxide concentration in the composite system / Sistemas h?bridos formados a partir de pol?meros e metais de transi??o atualmente t?m suas propriedades f?sicas e qu?micas extensivamente investigadas para aplica??o em dispositivos eletr?nicos. Neste trabalho, o Di?xido de Tit?nio (TiO2) a partir do precursor Tetrabut?xido de Tit?nio e o sistema comp?sito Poli (Etileno Glicol)-Di?xido de Tit?nio (PEG-TiO2) foram sintetizados pelo m?todo sol-gel. O PEG como adquirido e os p?s de TiO2 e comp?sitos obtidos foram analisados por Difra??o de Raios X (DRX), Espectroscopia de Absor??o na regi?o do Infravermelho com Transformada de Fourier (EIV-TF), An?lise Termogravim?trica (TG), Microscopia Eletr?nica de Varredura (MEV) e Espectroscopia de Imped?ncia Eletroqu?mica (EIE). Nas an?lises por DRX foram observadas no TiO2, faces cristalinas de um de seus polimorfos fase anat?sio, planos cristalinos no PEG com intensidade substancial e nos sistemas comp?sitos a mistura de faces cristalinas dos seus precursores na forma isolada, bem como, redu??o da cristalinidade. As curvas TG/DTG sugeriram o aumento da instabilidade t?rmica do PEG nos p?s comp?sitos ? medida que TiO2 ? incorporado ao sistema. A an?lise espectral na regi?o do infravermelho apresentou sobreposi??o de bandas relativas ao pol?mero e ao ?xido met?lico, redu??o da intensidade de estiramentos sim?tricos dos grupos ligantes da cadeia principal polim?rica e deforma??es angulares; foram observadas atrav?s das micrografias de MEV modifica??es morfol?gicas sofridas pelos sistemas comp?sitos com a varia??o da concentra??o do ?xido. As an?lises por imped?ncia eletroqu?mica indicaram que o aumento da condutividade nos comp?sitos ocorre em conson?ncia com a adi??o da concentra??o do ?xido met?lico no sistema comp?sito