No description available.

Thesis (MTech (Mechanical Engineering))--Cape Peninsula University of Technology, 2017. / Small and micro unmanned aerial vehicles (UAV) are rapidly becoming viable platforms for surveillance, aerial photography, firefighting and even package delivery. While these UAVs that are of the rotorcraft type require little to no extra infrastructure for their deployment, they are typically saddled with short ranges and endurance, thus placing a restriction on their usage. On the other hand, UAVs that are of fixed wing type generally have longer range and endurance but often require a runway for take-off and landing which places a restriction on their usage. This project focuses on the development of a vertical take-off and landing (VTOL) UAV demonstrator suitable for integration on a small or mini flying wing UAV (a fixed wing UAV) to counteract the take-off and landing limitations of fixed wing type UAVs. This thesis first presents a propulsion characterisation experiment designed to determine the thrust and moment properties of a select set of propulsion system components. The results of the characterisation experiment identified that the propulsion set of a Turnigy C6374 – 200 brushless out runner electric motor driving a 22 x 10 inch three bladed propeller will provide approximately 79N (8kg) of thrust at 80% throttle (4250rpm). Therefore, two of these propulsion set would satisfy the platform requirement of 12kg maximum take-off mass (MTOM). The result of the abovementioned experiment, together with the VTOL platform requirements were then used as considerations for the selection of the suitable VTOL method and consequently the design of the propulsion configuration. Following a comparison of VTOL methods, the tilt-rotor is identified as the most suitable VTOL method and a variable speed twin prop concept as the optimal propulsion configuration.

Thesis (MTech (Mechanical Engineering))--Cape Peninsula University of Technology, 2015. / Currently non-destructive testing techniques for composite aircraft structures are disadvantaged when compared to online Structural Health Monitoring (SHM) systems that monitor the structure while in-service and give real time data. The present research work looks at developing a protocol for online structural health monitoring of a UAV wing structure using PVDF film sensors, especially including the monitoring of structural changes caused by defects. Different types of SHM techniques were studied in relation to carbon fibre composites. Laminate composite make-up and manufacturing process was investigated and vacuum infusion process was used to manufacture the samples that resemble the Guardian II wing structure, then the three-point bending test was used to determine the material properties. Digital Shearography was employed as a stationery non-destructive technique to determine the sensor to structure attachment, type and position of defects that affect the state of performance. Finite Element Analysis (FEA) was done using ANSYS Workbench which served as a modelling tool using a drawing imported from Solid-works. Experimental investigation was done using PVDF sensor embedded on the surface of the sample in a cantilever setup and a vertical Vernier scale to measure the deflection due to impact and vibration loading. A Fluke-View oscilloscope was used as a data logger when the measurement of the output voltage and the natural frequency were recorded. The techniques of using FEA and experimental investigation were then compared. The findings of this study showed that the PVDF sensor is suitable for condition monitoring of a UAV wing structure.

This dissertation investigates the development of a methodology suitable for the evaluation of advanced propulsion concepts. At early stages of development, both the future performance of these concepts and their requirements are highly uncertain, making it difficult to forecast their future value. A systematic methodology to identify potential advanced propulsion concepts and assess their robustness is necessary to reduce the risk of developing advanced propulsion concepts. Existing advanced design methodologies have evaluated the robustness of technologies or concepts to variations in requirements, but they are not suitable to evaluate a large number of dissimilar concepts. Variations in requirements have been shown to impact the development of advanced propulsion concepts, and any method designed to evaluate these concepts must incorporate the possible variations of the requirements into the assessment. In order to do so, a methodology had to do two things. First, it had to systemically identify a probabilistic distribution for the future requirements. Such a distribution would allow decision-makers to quantify the uncertainty introduced by variations in requirements. Second, the methodology must assess the robustness of the propulsion concepts as a function of that distribution. These enabling elements have been synthesized into new methodology, the Evolving Requirements Technology Assessment (ERTA) method. The ERTA method was used to evaluate and compare advanced propulsion systems as possible power systems for a hurricane tracking, High Altitude, Long Endurance (HALE) unmanned aerial vehicle (UAV). The problem served as a good demonstration of the ERTA methodology because conventional propulsion systems will not be sufficient to power the UAV, but the requirements for such a vehicle are still uncertain.