Transdermal drug delivery systems (TDS) are pharmaceutical devices that are designed to deliver specific drugs to the human body by diffusion through skin. The TDS effectiveness suffers from crystallization in the patch when they are kept in storage for more than two years. It has been reported that there are two types of crystals in the patch: needle and aggregate, and growth of drug crystals in TDS generally occurs only in the middle third of the polymer layer. In our study, fluorescence microscopy, EDS (SEM) and Raman microspectroscopy were used to further characterize the crystals. The results show that the needle crystals most probably contain estradiol and acrylic resin conjugate. The FTIR spectrum of the model sample proved the occurrence of a reaction between estradiol and acrylic resin. Crystal growth in an unstressed matrix of a dissolved crystallizable drug component was simulated using a kinetic Monte Carlo model. Simulation using Potts model with proper boundary condition gives the crystals in the middle of matrix in the higher temperature. Bond fluctuation model is also being implemented to study representative dense TDS polymer matrix. This model can account for the size effect of polymer chain on the crystal growth. The drug release profile from TDS was also studied by simulating the diffusion of drug molecules using Monte Carlo techniques for different initial TDS microstructure. The release rate and profile of TDS depend on the dissolution process of the crystal. At low storage temperature, the grains are evenly distributed throughout the thickness of the TDS patch, thus the release rate and profile is similar to the randomly initiated system. Further work on stress induced crystallization is currently under development. Although the study was specifically done for drug in a polymer medium, the techniques developed in this investigation is in general applicable to any constrained crystallization in a polymer medium.

Fundação Carlos Chagas Filho de Amparo a Pesquisa do Estado do Rio de Janeiro / Neste estudo foram preparados polimorfos do fármaco tolbutamida, um hipoglicemiante oral usado no tratamento dos Diabetes Mellitus tipo II. Foram também preparados polimorfos da nifedipina, fármaco usado no tratamento das desordens cardiovasculares, como angina pectoris e hipertensão. A preparação dos polimorfos foi mediada por solvente, ou seja, foi em função do solvente usado nas etapas de cristalização e de precipitação das espécies. Um método de resfriamento rápido por nitrogênio líquido também foi utilizado. Técnicas analíticas como a espectrofotometria de infravermelho, a calorimetria diferencial de varredura, a difratometria de raio-X e a microscopia eletrônica de varredura foram úteis para a caracterização dos produtos obtidos experimentalmente. Os resultados comprovaram que dois polimorfos da tolbutamida foram preparados, ambos com estrutura cristalina. No caso da nifedipina, dois polimorfos foram preparados e a caracterização mostrou que um destes foi obtido num estado amorfo enquanto o outro estava sob forma cristalina. A instabilidade da nifedipina no estado amorfo foi monitorada pela técnica de calorimetria diferencial de varredura que, através de diferentes curvas, mostrou uma transformação rápida para uma estrutura cristalina. Esta mesma técnica aliada à termogravimetria confirmou a obtenção de um terceiro produto da nifedipina, de estrutura cristalina, que foi considerado um pseudopolimorfo por ser uma espécie solvatada. Ao final do procedimento experimental e da avaliação dos resultados foi sugerido um esquema, passo a passo, para obtenção e caracterização de polimorfos de uma substância / In this study the polymorphs of tolbutamide, an oral hypoglicemiant used on Diabetes Mellitus type II treatment, and of nifedipine, a drug used in the cardiovascular disorders treatment, were prepared. All crystalline forms were obtained by crystallization from different solvents. Tolbutamide was isolated only in crystalline forms and nifedipine in two crystalline forms and in the amorphous form prepared by melting and subsequent cooling. The polymorphs from each drug were characterized by powder x-ray diffraction (PDRX), infrared spectroscopy (IR), Raman spectroscopy (FT-RAMAN), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The results proved that two different crystalline forms of tolbutamide were obtained and two crystalline form to nifedipine, one of them as a pseudo-polymorph. The characterization confirmed that melting and quickly cooling procedure prepared amorphous nifedipine. Differential scanning calorimetry technique generated curves whose data proved that the amorphous nifedipine is a very unstable form. Thermogravimetry confirmed a pseudo-polymorphs preparation of nifedipine. In spite of the modification observed on the profile of X-ray diffraction, because of the solvent present, was possible to prove that this solvated form have an crystalline structure. A methodology was proposed step by step to prepare and characterize polymorphs of a substance