Over the past decade, intensive academic and commercial interests have been paid on compounds possessing photochemical properties, namely for their preparation, chemical properties, high efficiency and potential low-cost. Compounds having intense photochemical properties gained great interest due to wide range of potential applications. The sensitizers are one of the key components for high power-conversion efficiency in the dye sensitized solar cells (DSSCs). They are the core components in the organic light-emitting devices (OLEDs) due to their ability to emit light with the wavelengths largely red- shifted from their absorption wavelength. Ruthenium based sensitizers have been tagged “molecular light switches” because, although the fluorescence of these complexes in aqueous solutions is negligible, it increases of greater than 10000 fold in the presence of DNA. Many polypyridyl and dipyrido phenazine ruthenium complexes have achieved high power conversion efficiencies and therefore are of practical interest. Several research groups stated that the dipyrido phenazine ligand may be thought of as comprising two components: a bipyridyl unit and a phenazine unit. These two subunits behave essentially separately, with many molecular orbitals being localised over only one subunit and a redox properties of central phenazine moiety in the dipyrido phenazine ligand are important for the photochemical applications. Therefore a phenazine ligand was selected as a model for the present investigation. The chemistry of phenazine ligand is mostly limited to the late transition metal and f - element complexes. Our laboratory has a rich backgroung in the aluminum and early transition metal chemistry. The aluminum chemistry and early transition metal chemistry are of great interest since aluminum and early transition metal complexes are environmentally friendlier and cheaper than the late transition metal compounds. Another drawback of the ruthenium-based sensitizers is the lack of absorption in the red region of the visible spectrum, and also low molar extinction coefficients. An essential requirement for efficient conversion of solar energy is the good spectral match of the sensitizer absorption to the emission spectrum of solar radiation. In this regard, the ruthenium sensitizers’ spectral response in the lower energy regions is not sufficient. The current project has three parts. In the first part we collected and reviewed known literature regarding the certain classes of non-innocent ligands containing the six-membered carbon- nitrogen heterocycles and regarding the ligands potentially important for the photochemical applications. We also reviewed all available to the data information about the complexes supported by the phenazine ligand. In the second part we have investigated interaction of alkylaluminum compounds and phenazine and observed reduction of phenazine accompanied by formation of dialuminum cage type compounds containing two formally mononegative phenazine ligand. The derivatization of phenazine has been also observed. It resulted in formation of compounds having a stable organic radical. In a third part of our project we have explored interaction of phenazine or thiophenazine with the alkylaluminum compounds and chromium dichloride. The reaction in the three component system resulted in reduction of phenazine ligand and lead to the heterometallic Cr(II) - aluminum complexes containing a formally dinegative phenazine or thiophenazine ligands. When a large excess of triethylaluminum was taken, reduction of phenazine and chromium has been observed leading to the heterometallic multinuclear Cr(I) - aluminum complex containing a formally dinegative phenazine ligands and two chromium atoms in one complex in the rare oxidation state one.

Supramolecular chemistry - chemistry of non-covalent bonds including different type of intermolecular interactions viz., ion-pairing, ion-dipole, dipole-dipole, hydrogen bonding, cation-p and Van der Waals forces. Applications based on supramolecular concepts for developing catalysts, molecular wires, rectifiers, photochemical sensors have been evolved during recent years. Mimicking natural photosynthesis to build energy harvesting devices has become important for generating energy and solar fuels that could be stored for future use. In this dissertation, supramolecular chemistry is being explored for creating light energy harvesting devices. Photosensitization of semiconductor metal oxide nanoparticles, such as titanium dioxide (TiO2) and tin oxide (SnO2,), via host-guest binding approach has been explored. In the first part, self-assembly of different porphyrin macrocyclic compounds on TiO2 layer using axial coordination approach is explored. Supramolecular dye sensitized solar cells built based on this approach exhibited Incident Photon Conversion Efficiency (IPCE) of 36% for a porphyrin-ferrocene dyad. In the second part, surface modification of SnO2 with water soluble porphyrins and phthalocyanine resulted in successful self-assembly of dimers on SnO2 surface. IPCE more than 50% from 400 - 700 nm is achieved for the supramolecular self-assembled heterodimer photocells is achieved. In summary, the axial ligation and ion-pairing method used as supramolecular tools to build photocells, exhibited highest quantum efficiency of light energy conversion with panchromatic spectral coverage. The reported findings could be applied to create interacting molecular systems for next generation of efficient solar energy harvesting devices.

Porphyrins offer a very synthetically flexible template which can be modified in numerous ways to synthesize molecules with very useful properties applicable in areas such as non-linear optical properties, photodynamic therapy, dye-sensitized solar cells, chemical sensors and organic electronic devices. β-Substituted π-extended porphyrins offer unique capabilities in tuning the properties of the molecule towards practical applications. Increased π-conjugation allows the HOMO-LUMO gap to decrease and hence to redshift the absorption into the near-IR region. β-Fused benzoporphyrins offer additional benefits in which the benzene ring itself can be further modified using electron donating substituents and electron donating substituents to electronically tune these porphyrins for various uses. The goal of the research pursued in this dissertation was to develop new methods for the development of β-Substituted π-extended porphyrins and to study their optical and electronic properties. To accomplish this goal, we developed new method to synthesize A2B2 type tetrabenzoporphyrins and we studied the electron transfer in such systems. We also studied the effectiveness of such systems in dye sensitized solar cells. A new method to synthesize functionalized naphthalene fused porphyrins was also developed and we were also able to use this method to synthesize a push-pull naphthalene fused porphyrin.

In order to become a viable alternative to silicon photovoltaics, dye-sensitized solar cells must overcome several issues primarily resulting from their use of a liquid electrolyte. Much research has gone into correcting these shortcomings by replacing the liquid electrolyte with solid-state hole-transport media. Using these solid-state materials brings new difficulties, such as completely filling the pores in the TiO₂nanostructure, and achieving good adhesion with the dye-coated TiO₂. A novel approach to addressing these difficulties is the inverse dye-sensitized solar cell design. In this method the devices are constructed in reverse order, with the solid-state hole-transport medium providing the nanostructure instead of the TiO₂. This allows new materials and methods to be used which may better address these issues. In this project, inverse dye-sensitized solar cells using polyaniline nanofibers as the hole transport medium were prepared and characterized. The devices were prepared on fluorine-doped tin oxide (FTO) coated glass electrodes. The first component was a dense spin-coated polyaniline blocking layer, to help prevent short circuiting of the devices. The second layer was a thin film of drop cast polyaniline nanofibers which acted as the hole transport medium and provided high surface area for the dye attachment. The dye used was 5,10,15,20-tetrakis (4-carboxyphenyl) porphyrin (TCPP), which was covalently attached to the nanofibers using a Friedel-Crafts acylation. Titania gel was then deposited into the pores of the nanofiber film by controlled hydrolysis of a titanium complex (Tyzor LA). A back electrode of TiO₂nanoparticles sintered on FTO was pressed on top to complete the devices. A typical device generated an open circuit voltage of 0.17 V and a closed circuit current of 5.7 nA/cm² while the highest open circuit voltage recorded for any variation on a device was 0.31 V and the highest short circuit current was 52 nA/cm² under AM 1.5 simulated olar spectrum at 100 mW/cm². Initially prepared devices did not generate a measureable photocurrent due to two materials flaws. The first was traced to the poorly developed conduction band of the titania gel, as deposited from Tyzor LA hydrolysis, resulting in poor electron conduction. This prevented the titania gel from efficiently functioning as the electron transport medium. A remedy was found in adding a layer of sintered anatase TiO₂nanoparticles on the back electrode to serve as the electron transport medium. However, this remedy does not address the issue of the inability of titania gel to efficiently transport electrons photogenerated deep in the nanofiber film to the back electrode. The second flaw was found to originate from fast recombination kinetics between electrons in TiO₂and holes in polyaniline. However, a positive feature was that the titania gel intended to be used as the electron transport medium was found to sufficiently insulate the interface such that the recombination rate slowed enough to allow generation of a measureable photocurrent. Electronic insulation was further enhanced by co-attaching decanoic acid onto the polyaniline nanofibers to fill in pinholes between the dye molecules. While these solutions were not ideal, they were intended to be diagnostic in nature and supplied critical information about the weak links in the device design, thus pointing the way toward improving device performance. Significant enhancements can be expected by addressing these issues in further detail.

No description available.

No description available.

No description available.

This thesis is divided into four parts with organic chromophores for dye sensitized solar cells as the common feature and an introduction with general concepts of the dye sensitized solar cells. The first part of the thesis describes the development of an efficient organic chromophore for dye sensitized solar cells. The chromophore consists of a triphenylamine moiety as an electron donor, a conjugated linker with a thiophene moiety and cyanoacrylic acid as an electron acceptor and anchoring group. During this work a strategy to obtain an efficient sensitizer was developed. Alternating the donor, linker or acceptor moieties independently, would give us the tool to tune the HOMO and LUMO energy levels of the chromophores. The following parts of this thesis regard this development strategy. The second part describes the contributions to the HOMO and LUMO energy levels when alternating the linker moiety. By varying the linker the HOMO and LUMO energy levels was indeed shifted. Unexpected effects of the solar cell performances when increasing the linker length were revealed, however. The third part describes the investigation of an alternative acceptor group, rhodanine-3-acetic acid, in combination with different linker lengths. The HOMO and LUMO energy level tuning was once again successfully shifted. The poor electronic coupling of the acceptor group to the semiconductor surface proved to be a problem for the overall efficiency of the solar cell, however. The fourth part describes the contributions from different donor groups to the HOMO and LUMO energy levels and has so far been the most successful in terms of reaching high efficiencies in the solar cell. A top overall efficiency of 7.1 % was achieved. / QC 20101108

This is my thesis research on the preparation of borylazadipyrromethene (azaBODIPY) dyes bearing an anchoring group, such as a carboxylic acid group, at the β-pyrrolic position of the azadipyrromethene scaffold. Carboxylate groups form covalent bonds to oxide semiconductors such as TiO2 (n-type) or Cu2O (p-type) in dye-sensitized solar cells (DSCs) or photogalvanic dye-sensitized solar cells (P-DSCs). Oxide-binding azaBODIPY dyes can be used to investigate the rate and mechanism of electron injection from the dyes to the semiconductors. Two different types of azaBODIPY (difluoroboryl and dialkynylboryl) were prepared by following previously developed methods. To convert difluoroborylazaBODIPY to the final dyes having a carboxylic acid in the β-pyrrolic position, several distinct synthetic routes were designed, adopting various reactions, such as halogenation, Sonogashira coupling, Knoevenagel condensation, Grignard reagents, Vilsmeir-Haack, and Steglich esterification. Some of these reactions were successful, but the overall synthesis to the targeted final molecule couldn’t be accomplished. Even though further studies on the synthesis of oxide-binding azaBODIPYs are needed, at least my thesis research suggests what reactions can be implemented to complete this synthesis in the future. Proton NMR (nuclear magnetic resonance) and carbon NMR were commonly used to confirm the synthesized compounds, and sometimes crystallographic information was obtained by XRD (X-ray diffraction) whenever crystals of sufficient size and quality were grown. NMR spectra, interpreted by SpinWorks 3 software, and crystal structures will be introduced in each chapter.

Master of Science / Department of Chemistry / Jun Li / With the increasing consumption of energy and the depletion of fossil fuels, finding an alternative energy source is critical. Solar energy is one of the most promising energy sources and solar cells are the devices that convert solar radiation into electricity. Currently, the most widely used solar cell is based on p-n junction formed with crystalline silicon materials. While showing high efficiency, the high fabrication cost limits its broad applications. Dye sensitized solar cell (DSSC) is a promising low-cost alternative to the Si solar cell, but its efficiency is much lower. Improvements in materials and interfaces are needed to increase the DSSC efficiency while maintain the low cost. In this thesis, three projects were investigated to optimize the DSSC efficiency and reduce the cost. The first project is to optimize the TiO[subscript]2 barrier layers on Fluorine-doped Tin Dioxide (FTO) surface. Two preparation methods, i.e. TiCl[subscript]4 solution treatment and thermal oxidation of sputtered Ti metal films, were employed and systematically studied in order to minimize electron-hole recombination and electron backflow during photovoltaic processes of DSSCs. TiCl[subscript]4 solution treatment method was found to create a porous TiO[subscript]2 barrier layer. Ti sputtering method created a very compact TiO[subscript]2 blocking layer. Two methods showed different characteristics and may be used for different DSSC studies. The second project is to reduce the DSSC cost while maintaining the efficiency by replacing the expensive Pt counter electrode with a novel vertically aligned carbon nanofiber (VACNF) electrode. A large specific electrode surface area (~125 cm[superscript]2 over 1 cm[superscript]2 geometric area) was obtained by using VACNFs. The relatively high surface area, good electric conductivity and the large numbers of active graphitic edges existed in cone-like microstructure of VACNFs were employed to improve redox reaction rate of I[subscript]3[superscript]-/I[superscript]- mediators in the electrolyte. Faster electron transfer and good catalytic activities were obtained with such counter electrodes. The third project is to develop a metal organic chemical vapor deposition (MOCVD) method to coat TiO[subscript]2 shells on VACNF arrays as potential photoanodes in the DSSC system in order to improve the electron transfer. Fabrication processes were demonstrated and preliminary materials were characterized with scanning electron microscopy and transmission electron microscopy. MOCVD at 300 mTorr vapor pressure at 550° C for 120 min was found to be the optimal condition.