Spelling suggestions: "subject:"1plastic solids"" "subject:"2plastic solids""
41 |
LEFM based analysis of the effect of tensile residual macrostress on fatigue crack propagation /Prawoto, Yunan, January 2000 (has links)
Thesis (Ph. D.)--University of Missouri-Columbia, 2000. / Typescript. Vita. Includes bibliographical references (leaves 182-188). Also available on the Internet.
|
42 |
Contact mechanics and impact dynamics of non-conforming elastic and viscoelastic semi-infinite or thin bonded layered solidsVotsios, Vasilis January 2003 (has links)
The thesis is concerned with the contact mechanics behaviour of non-conforming solids. The geometry of the solids considered gives rise to various contact configurations, from concentrated contacts with circular and elliptical configuration to those of finite line nature, as well as those of less concentrated form such as circular flat punches. The radii of curvature of mating bodies in contact or impact give rise to these various nonconforming contact configurations and affect their contact characteristics, from those considered as semi-infinite solids in accord with the classical Hertzian theory to those that deviate from it. Furthermore, layered solids have been considered, some with higher elastic modulus than that of the substrate material (such as hard protective coatings) and some with low elastic moduli, often employed as tribological coatings (such as solid lubricants). Other bonded layered solids behave in viscoelastic manner, with creep relaxation behaviour under load, and are often used to dampen structural vibration upon impact. Analytic models have been developed for all these solids to predict their contact and impact behaviour and obtain pressure distribution, footprint shape and deformation under both elastostatic and transient dynamic conditions. Only few solutions for thin bonded layered elastic solids have been reported for elastostatic analysis. The analytical model developed in this thesis is in accord with those reported in the literature and is extended to the case of impact of balls, and employed for a number of practical applications. The elastostatic impact of a roller against a semi-infinite elastic half-space is also treated by analytic means, which has not been reported in literature. Two and three-dimensional finite element models have been developed and compared with all the derived analytic methods, and good agreement found in all cases. The finite element approach used has been made into a generic tool for all the contact configurations, elastic and viscoelastic. The physics of the contact mechanical problems is fully explained by analytic, numerical and supporting experimentation and agreement found between all these approaches to a high level of conformance. This level of agreement, the development of various analytical impact models for layered solids and finite line configuration, and the development of a multi-layered viscoelastic transducer with agreed numerical predictions account for the main contributions to knowledge. There are a significant number of findings within the thesis, but the major findings relate to the protective nature of hard coatings and high modulus bonded layered solids, and the verified viscoelastic behaviour of low elastic modulus compressible thin bonded layers. Most importantly, the thesis has created a rational framework for contact/impact of solids of low contact contiguity.
|
43 |
One-sided ultrasonic determination of third order elastic constants using angle-beam acoustoelasticity measurementsMuir, Dave D. 12 May 2009 (has links)
This thesis describes procedures and theory for a family of one-sided ultrasonic methods for determining third order elastic constants (TOEC) using sets of angle-beam wedges mounted on one side of a specimen. The methods are based on the well-known acoustoelastic effect, which is the change of wave speed with applied loads and is a consequence of the mechanical nonlinearity of a material. Increases in material nonlinearity have been correlated to the progression of damage, indicating that tracking changes in TOECs may provide a practical means of monitoring damage accumulation at the microstructural level prior to formation of macroscopic defects.
Ultrasonic methods are one of the only ways to measure TOECs, and most prior techniques have utilized wave propagation paths parallel and perpendicular to the loading directions. A few additional ultrasonic techniques reported in the literature have employed oblique paths but with immersion coupling. These reported techniques are generally unsuitable for field implementation. The one-sided contact approach described here is applicable for in situ measurements of TOECs and thus lays the foundation for tracking of TOECs with damage.
Theory is reviewed and further developed for calculating predicted velocity changes, and thus time shifts, as a function of uniaxial tensile loading for longitudinal, shear vertical, and shear horizontal waves in the context of angle-beam transducers mounted on the surface of the specimen. A comparison is made to published results where possible. The inverse problem of determining the three TOECs of an isotropic material from three measurements employing three different angle beam configurations is comprehensively analyzed. Four configurations providing well-posed solutions are identified and examined. A detailed sensitivity analysis is carried out to identify the best mounting configuration, wave mode combinations, refracted angles and geometry requirements for recovering the three TOECs.
Two transducer mounting configurations are considered: (1) attached (glued-on) transducers potentially suitable for in situ monitoring, and (2) floating (oil-coupled) transducers potentially suitable for single measurements. Limited experimental results are presented for the attached case using two longitudinal measurements and one shear vertical measurement. The floating case experiments utilized three of the four well-posed solutions, and measurements were made on several aluminum alloys and low carbon steel. Key experimental issues are identified and discussed for both transducer mounting configurations.
|
44 |
Hydrogel Microparticles as Sensors for Specific Adhesion: Case Studies on Antibody Detection and Soil Release PolymersStrzelczyk, Alexander Klaus, Wang, Hanqing, Lindhorst, Andreas, Waschke, Johannes, Pompe, Tilo, Kropf, Christian, Luneau, Benoit, Schmidt, Stephan 06 April 2023 (has links)
Adhesive processes in aqueous media play a crucial role in nature and are important for
many technological processes. However, direct quantification of adhesion still requires expensive
instrumentation while their sample throughput is rather small. Here we present a fast, and
easily applicable method on quantifying adhesion energy in water based on interferometric
measurement of polymer microgel contact areas with functionalized glass slides and evaluation via
the Johnson–Kendall–Roberts (JKR) model. The advantage of the method is that the microgel matrix
can be easily adapted to reconstruct various biological or technological adhesion processes. Here we
study the suitability of the new adhesion method with two relevant examples: (1) antibody detection
and (2) soil release polymers. The measurement of adhesion energy provides direct insights on the
presence of antibodies showing that the method can be generally used for biomolecule detection. As a
relevant example of adhesion in technology, the antiadhesive properties of soil release polymers used
in today’s laundry products are investigated. Here the measurement of adhesion energy provides
direct insights into the relation between polymer composition and soil release activity. Overall, the
work shows that polymer hydrogel particles can be used as versatile adhesion sensors to investigate
a broad range of adhesion processes in aqueous media.
|
Page generated in 0.061 seconds