This investigates the voltage flicker problem of a large steel plant and presents the mitigation strategy by applying the static var compensator (SVC) and cogenerator. The fluctuation of real power and reactive power consumption by an arc furnace has been measured and recorded during the steel production process. The dynamic load model of the A/C arc furnace is derived based on the actual field data and has been included in the computer simulation by the CYME software package for load flow analysis. The block diagrams of SVC controller and the excitation system of cogenerators are considered to solve the response of reactive power compensation according to the voltage fluctuation of the control bus. To maintain the electric service reliability of arc furnace when an external utility fault occurs, the tie line tripping and load shedding is implemented to prevent the tripping of cogenerator after system disturbance. It is found that the dynamic load behavior of arc furnace in the isolated industrial power system can be well compensated by the cogenerator with adaptive control of exciter and governor to generate proper reactive power and real power according to the fluctuation of bus voltage and system frequency respectively.

Electric Arc Furnace (EAF) modeling has been a common research area to date. This thesis work proposes a new field-data based EAF-specific model. The data used in developing the proposed model is obtained from field measurements of instantaneous voltages and currents of EAF the plants. This model presents the dynamic behavior of the EAF system including all its parts, which are the EAF transformer, the secondary circuit, the electrodes moving and the arc itself. It consists of a cascade connected variable-resistance and &ndash / inductance combination to represent the variation in time of the fundamental frequency, and a current source in parallel with it to inject the harmonics and interharmonics content of the EAF current. The proposed model is capable of representing both AC and DC EAFs, whose controllers&rsquo / set points are the impedance values seen from the low voltage (LV) side of the EAF transformer. The validity of the proposed model has been verified by comparing EMTDC/PSCAD simulations of the model with the field measurements. The results obtained have shown quite satisfactory correlation between the behavior of the proposed model and v the actual EAF operation. To show the advantages of the model while developing FACTS solutions for power quality (PQ) problem mitigation of a given busbar supplying single- or multi-EAF installations, various applications are presented.

The landfilling of slag obtained from the high alloyed Electric Arc Furnace (EAF) steel making process, constitutes an environmental treat for society as well as an economical problem for the companies producing it, due to the costs related to waste management practices. Conventional methods of slag recycling are abundantly used among the steelmaking business, but due to their particular physical properties, high- alloyed EAF slags cannot be properly valorized. Moreover, the pickling process that high-alloyed EAF steels undergo to, generates acidic wastewaters, that need to be collected and neutralized, before they can be recirculated into the natural water streams. For such a task, steel mills currently utilize slaked lime (a Ca rich mineral) to raise the pH and to remove any metal particles dissolved into the wastewaters. Slag contains high amount of Ca; therefore, it has already been tested as a slaked lime replacement. In fact, previous studies conducted at the Material Science and Engineering department at KTH Royal Institute of Technology showed, on a laboratory scale, that slag has the potential to replace lime for the neutralization and purification of the acidic wastewaters. This Master’s thesis project aims at upscaling the volumes of wastewaters to be tested, about 70 to 90 folds of the one from previous research, bridging the gap between laboratory tests and the industrial scale. The thesis is divided into three tranches, a first part where a water-salt solution conductivity trials were carried out, to model the behavior or slag dispersion in the acidic wastewaters. After the results obtained from the conductivity trials, neutralization trials with slag and the lime product currently in use by the company, were carried out at the neutralization plant in Outokumpu Stainless, Avesta (Sweden). The neutralization trials were carried out with 70 and 90 liters of acidic wastewaters and in order to perform the trials on site, the slag sample was dried and later sieved to a particle size of less than 350μm. Moreover, data was analyzed and compared to previous studies in order to have a clearer understanding regarding the neutralization efficiency of the slag, especially whether or not the technology would had worked on upscaled volumes. Additionally, the project checked if it was possible to find a generalized relationship between the mass of slag and volume of wastewaters required for the neutralization process. Slag demonstrated to be able to buffer the pH to the target values of 9, while also showing an almost linear trend compared to previous studies. The reaction progress between slag, lime, and the acidic wastewaters was also analyzed. / Deponering av slagg som erhållits från den höglegerade ljusbågsugn (EAF) stålframställningsprocessen utgör en miljömässig behandling för samhället och ettekonomiskt problem för de företag som producerar den på grund av kostnaderna för avfallshantering. Konventionella metoder för återvinning av slagg används i storutsträckning bland stålindustrin, men på grund av deras speciella fysiska egenskaper kan höglegerade EAF-slaggen inte värderas ordentligt. Dessutom produceras sura avloppsvatten av betningsprocessen som höglegerade EAF-stål genomgår som sedan måste samlas in och neutraliseras innan de kan återcirkuleras i det naturliga vattnet. För en sådan uppgift använder stålfabriker för närvarande släckt kalk (ett Ca-rikt mineral) för att höja pH-värdet och för att avlägsna alla metallpartiklar som löses upp i avloppsvattnet. Slaggen innehåller hög mängd Ca och därför har den testats som en ersättning till släckt kalk. Tidigare studier utförda vid avdelningen materialvetenskap och teknik vid Kungliga Tekniska Högskola visade på laboratorieskala att slagg har potential att ersätta kalk för neutralisering och rening av sura avloppsvatten. Detta examensarbete syftar till att skala upp volymerna av avloppsvattnet som ska testas till cirka 70–90 gånger av den från tidigare forskning, och därav fylla ut bryggan mellan laboratorietester och industriell skala. Avhandlingen är uppdelad i tre delar, Första delen innehåller försök på ledningsförmåga i en vatten-saltlösning som genomfördes för att modellera beteende eller slaggspridning i sura avloppsvatten. Efter de resultat som erhållits från konduktivitetsmätningarna genomfördes neutraliseringsförsök med slagg och kalk som för närvarande används av företaget vid neutraliseringsanläggningen i Outokumpu Stainless, Avesta (Sverige). Neutraliseringsförsöken genomfördes med 70 och 90 liter sura avloppsvatten och för att utföra experimenten på plats torkades slagg provet och siktades senare till en partikelstorlek på mindre än 350 μm. Dessutom analyserades data och jämfördes med tidigare studier för att få en tydligare förståelse för slaggens neutraliseringseffektivitet, särskilt huruvida tekniken skulle ha fungerat på större volymer, och även om det också var möjligt att hitta ett generaliserat samband mellan mängden slagg och volym avloppsvatten som krävs för neutraliseringsprocessen. Slagget visade sig kunna buffra pH till målvärdena 9, samtidigt som den visade en nästan linjär trend jämfört med tidigare studier. Reaktionsförloppet mellan slaggkalk och de sura avloppsvattnen analyserades också.

Without a doubt, there is a consensus around the international community which suggests that our current way of life is unsustainable for a healthy planet, society and economy. One focal point that should be taken deeply into consideration is the steel industry as, globally, it accounts for 8% of global emissions. Thus, there is a dire need to incorporate drastic measures, if one wishes to reach net-zero emissions by 2050, in accordance with the Paris Agreement of 2015. Electric Arc Furnaces are seeing a rapid implementation in the steel industry. However, at 0.5 tonnes of CO2 emitted per tonne of liquid steel produced, this emissions rating is still significant considering the amount of steel being produced annually. Additionally, these furnaces emit off-gases which must be treated from the dust. This leaves operators with a conundrum as the dust content compromises the use of waste heat recovery boilers for energy recovery, due to constant breakdowns. Therefore, this study aims to analyse the feasibility of using bioenergy and carbon capture and utilisation (CCU) concepts to capitalise on the high off-gas energy and emissions content to remedy the dust issue, whilst producing higher value products. The proposed concept evaluates the effectiveness of using the off-gas as the energy carrier and feed-stock for a biogasificaiton unit. Three different cases based on different EAF off-gas compositions have been investigated. Case 1 suggested that the off-gas composition is very CO2-heavy, whichled to investigating the option of adopting a CO2 biogasification concept to directly use the CO2. Case 1 performed the best in terms of CO2 utilisation efficiency; being 0.293. The system energy utilisation also noted that 49.3% of the inlet streams energy was transferred to the desired product. On a broader picture, this means that around 11% of the total energy coming out of the EAF would be utilised in producing a value-added product in the form of syngas. This contrasts with allowing around 33% of the energy in the EAF either being completely dissipated to the environment or converting it into electricity via waste heat recovery. The following two cases, Case 2 and 3, indicate EAF off-gas composition containing 72% and 40% nitrogen respectively. For Cases 2 and 3, a steam biogasification process was integrated which did not yield positive results for CO2 utilisation, since is a more promising gasifying agent. In addition, significant energy from EAF off-gas is used in raising the temperature of steam to the design temperature of the gasifier. However, although the CO2 was not directly used in this part of the process, it allows for other opportunities of process integration, for example the reverse water-gas shift step.

Thesis (MScEng) --University of Stellenbosch, 2010. / ENGLISH ABSTRACT: This thesis deals with the development of a new process for the production of Direct Reduced Iron (DRI), intended for use specifically by small scale Electric Arc Furnace (EAF) based steel mills, who require small volumes of DRI. The term development as used here is taken to include such aspects as conceptual design, theoretical verification and initial practical testing. The rise of EAF steelmaking brought about the metamorphosis of steel scrap from a waste product into a valuable raw material. Scrap prices rose steeply during the period 1995 to 2009 compelling EAF steelmakers, wishing to have more control over the cost of their input material, to seek for scrap supplements or alternatives. DRI has become an accepted and sought after supplement, or even complete alternative, to steel scrap. Adding DRI to an EAF charge has a range of advantages, including the dilution of tramp elements and possible cost benefits, but it does have negative effects. These include the lowering of the scrap to liquid metal yield and an increase in power consumed. The effect of charging DRI to a small EAF is quantified. The maximum DRI that may be added to the burden whilst still maintaining the present steelmaking volume, is shown to be as high as 50% if charged continuously, and the maximum price payable for DRI, is shown to be approximately 80% of base grade scrap price. Finally other requirements unique to small scale EAF operators are considered in order to prepare a schedule of requirements for a DRI plant specifically for small scale EAF steel mills. A review of published information on existing DRI production technology, processes and plants is undertaken is establish the fit of existing processes to the requirements set. Initially the thermodynamics and kinetics of iron ore reduction and coal gasification, specifically downdraft gasification are reviewed. Thereafter existing processes are reviewed. Shaft based processes and rotary kiln based processes are identified as possible suitors to the requirements. Limitations of these processes, specifically heat transfer in rotary kilns and the pressure drop over a reduction shafts are investigated. Finally a typical process in each of the main process classes is adjudicated against the set requirements. None is found to match the set requirements. A new process is proposed that is claimed to better suit to small scale operation. The uniqueness of the process is embodied in the combination of existing technologies of downdraft gasification and iron ore reduction in a shaft, in a single reactor. The process consists of two shafts, one placed above the other. Iron ore is charged into the top shaft, called the pre-heat shaft, where it is pre-heated and lightly reduced to wustite with gas from the bottom shaft, called the reduction shaft. The pre-heated ore is then charged together with coal into the reduction shaft. Gasification air is drawn into the top of the reduction shaft where the coal is gasified in a downdraft gasifier, generating reduction gas which reduces the ore as the gas moves concurrently with the iron ore. The exit gas is cleaned and pumped to the pre-heat shaft where it combusted with air to pre-heat the iron ore in the pre-heat shaft. The concept is analysed thermodynamically using amongst others, FactSage, and is shown to be thermodynamically viable. To test the concept process concept practically, an extremely small pilot plant with a production rate of 2kg DRI/h, consisting of only a gasifier/reduction shaft, was designed and constructed using reduction rate data obtained from literature supplemented with data obtained from thermogravimetric analysis of CO reduction of lump Sishen hematite. Pilot Plant trials were performed using various reductant sources. The degree of metallizaion was analysed using visual inspection of cut and polished samples compared to calibrated standards. Analysis of the results indicate that coal rate and production rate influence the degree of reduction positively and negatively. The conclusions arrived at include the fact that the process is thermodynamically viable, that it was possible to reduce iron ore in a simplified pilot plant, and that the process was found to be stable and controllable. It is recommended that a larger scale pilot plant, embodying the full proposed flow sheet be erected to test the process more completely. / AFRIKAANSE OPSOMMING: Die tesis handel oor die the ontwikkeling van ‘n nuwe proses vir die vervaardiging van sponsyster. Die proses is beoog spesifiek vir gebruik deur kleinskaalse Elektriese Boogoond (EBO) gebaseerde staal aanlegte, wat kleiner hoeveelhede sponsyster benodig. Die term ontwikkeling soos hier gebruik word aanvaar om aspekte soos konseptuele ontwerp, teoretiese verifikasie en aanvanklike toetsing te behels. Die vinnige groei van EBO staalvervaardiging het skroot getransformeer van weggooiproduk tot waardevolle grondstof. Die prys van skroot het skerp gestyg gedurende die periode 1995 to 2009. EBO gebaseerde staal produsente, in ‘n poging om meer beheer te hê oor die koste van hul insetmateriaal, het hul in ‘n toenemende mate tot skrootalternatiewe gewend. Sponsyster het ‘n aanvaarde en gewaardeerde byvoeging, en selfs alternatief tot staalskroot geword. Die byvoeging van sponsyster by die lading van ‘n tipiese EBO het besliste voordele, maar het dit ook nadelige effekte. Die voordele sluit die verdunning van reselemente en moontlike kostevoordele in, terwyl van die nadele die verlaging van die skroot tot vloeistaal opbrengs, en ‘n verhoging in kragverbruik, is. Die effek van die byvoeging van sponsyster tot ‘n EBO lading word gekwantifiseer. Daar word getoon dat die maksimum hoeveelheid sponsyster wat by ‘n EBO lading gevoeg kan word terwyl die hoeveelheid staal geproduseer konstant gehou word, ongeveer 50% is indien die sponsyster kontinue gelaai word, en die maksimum prys wat vir die sponsyster betaal kan word, word bereken op ongeveer 80% van die prys van basisgraad skroot. Ander vereistes uniek aan kleinskaal EBO bedrywers word oorweeg ten einde ‘n lys van vereistes vir ‘n sponsysteraanleg, uniek aan kleinskaal EBO bedrywers, te kan bepaal. ‘n Oorsig van gepubliseerde inligting oor sponsysterproduksietegnologie word onderneem ten einde die passing van bestaande prosesse met die gestelde vereistes te kan bepaal. Nadat die termodinamika en kinetika van ysterertsreduksie en steenkoolvergassing be-oordeel is, word bestaande sponsysterprosesse beskou. Skag- en Roterende oond gebaseerde prosesse word as moontlik gepaste prosesse identifiseer. Hitte-oordrag en die drukval oor gepakte beddens, synde tipiese beperkings eie aan die twee prosesse, woord beskou. Tipiese prosesse in elk van die hoofklasse van prosesse word ten laaste be-oordeel aan die gestelde kriteria. Daar word bevind dat geeneen van die bestaande prosesse aan die vereistes voldoen nie. ‘n Nuwe proses, wat skynbaar die behoefte van kleinskaalse EBO gebaseerde staalprodusente beter bevredig, word voorgestel. Bestaande tegnolgie word in ‘n unieke opstelling geïntegreer. Reduksie word in ‘n reduksiekag gedoen as gevolg van die ooglopende massa- en hitte-oordragvoordele van ‘n skag. Reduksiegas word verkry van steenkoolvergassing in ‘n afstroomvergasser ten einde teerverwydering in ‘n naverwerkingsstap oorbodig te maak. Die uniekheid van die proses is beliggaam in die kombinasie van ‘n steenkoolvergasser en reduksieskag in ‘n enkele reaktor. Die proses bestaan uit twee skagte, een bo die ander. Ystererts word in die boonste skag, wat die voorverhitskag genoem word, gelaai. Hier word die erts voorverhit en moontlik lig gereduseer tot wustiet met gas van die onderste skag, wat die reduksieskag genoem word. Die voorverhitte erts word saam met steenkool in die reduksieskag gelaai. Vergassingslug, word in die reduksieskag gesuig waar die steenkool in ‘n afstroomvergasser vergas word. Hierdeur word reduksiegas gegenereer wat die erts verder reduseer soos dit saamstromend met die erts af beweeg. Die uitlaatgas word gesuiwer en na die voorverhitskag gepomp waar dit verbrand word om die erts te voorverhit. Die konsep is termodinamies analiseer met gebruikmaking van onder andere FactSage, en werkbaar bevind. ‘n Baie klein, vereenvoudigde proefaanleg, met ‘n produksievermoë van 2kg DRY/uur, bestaande uit slegs ‘n reduksiekag, is ontwerp en gebou met gebruikmaking van kinetika inligting uit die literatuur aangevul met inligting uit termogravimetriese analise van die CO reduksie van Sishen hematiet. Proefaanleglopies is uitgevoer met ‘n reeks reduktantbronne. Die metallisasiegraad is bepaal deur visuele inspeksie van gesnyde, gepoleerde monsters wat vergelyk is met gekalibreerde standaarde. Analise van die resultate toon dat die steenkoolkoers ‘n positiewe verband, en die produksiekoers ‘n negatiewe verband met die metallisasiegraad het. Die slotsom waartoe gekom is, is dat die proses termodinamies werkbaar is, dat reduksie van ystererts in ‘n vereenvoudigde proefaanleg bewerk kon word, en dat die prose stabiel en beheerbaar voorgekom het. Die aanbeveling word gemaak dat ‘n groter proefaanleg wat die volledige voorgestelde vloeiskema verteenwoordig, opgerig behoort te word, ten einde die proses meer volledig te kan toets.

Esta tese apresenta os métodos de gerenciamento associados ao Pó de Aciaria Elétrica (PAE) gerado no forno elétrico a arco (FEA) e no forno-panela (FP), envolvendo dois grandes tópicos: sistema de gestão ambiental e fatores relacionados à tecnologia. O processo do PAE percorre as seguintes etapas: entrada e beneficiamento da matériaprima, preparação, carregamento e fusão de carga no FEA, formação e retirada de escória, vazamento do aço para a panela, refino no forno-panela, assim como o sistema de captação das emissões atmosféricas e destinação do PAE captado no FEA e FP. Os métodos de gerenciamento foram estruturados em cima do aprendizado técnico, qualitativo e quantitativo adquirido no desenvolvimento das atividades profissionais, dos levantamentos sobre as tecnologias disponíveis para destinação e reciclagem do PAE, dos mapeamentos das características das instalações de captação do PAE de empresas siderúrgicas, bem como das bibliografias e visitas técnicas realizadas. As informações reunidas foram empregadas para desenvolver duas matrizes de avaliação, consolidando assim, um critério para verificar as práticas de gestão ambiental e de tecnologias que estão associadas ao PAE. O principal resultado das matrizes foi a identificação e priorização das necessidades de melhorias, tanto do sistema de gestão ambiental como da área de tecnologia. A avaliação das empresas siderúrgicas, segundo estas matrizes, mostrou quais práticas possuem menores valores e que, por conseqüência, devem requerer maior esforço para melhorar seus desempenhos, bem como aquelas de maior valor que requerem uma consolidação da sua rotina para manterem o elevado nível de desempenho atingido. Como conclusão, foi obtida uma ferramenta robusta que respondeu de forma consistente a avaliação do processo do PAE e a pergunta sobre “O que se encontra mais desenvolvido, os processos de gestão ou os de tecnologia?”. As matrizes de avaliação foram preenchidas por especialistas ambientais de três Empresas siderúrgicas. O resultado obtido com essa ferramenta mostrou que os desempenhos sobre as práticas de gestão são superiores aos desempenhos das práticas de tecnologia e que esta metodologia de avaliação está apta para ser aplicada em qualquer outro processo ou empresa. Ficou evidenciado que o conhecimento e a inteligência ambiental são requisitos para assegurar que as estratégias de médio e longo prazo estejam corretamente alinhadas às boas práticas de gestão e melhores tecnologias disponíveis. / The thesis presents the methods associated with the management of the electric arc furnace (EAF) baghouse dust and ladle furnace (LF) dust. The management methods cover two broad topics: environmental management system practices and technology related factors. The EAF baghouse dust and ladle furnace (LF) dust process has the following steps: input and processing raw materials, EAF charging and melting, slag generation and removal, furnace tapping of the steel to the LF, refining in the LF, as well as the EAF dedusting system, dust recycling and final destination. The management methods were determined based on professional experience of the author, assessment of typical installations of steel plant dedusting system, bibliographies review, available technologies to EAF/LF dust destination and recycling and subject technical literature, as well technical visits undertaken. Collectively the information was used to develop two standard evaluation standard matrices which provide criteria to assess environmental management system practices and technology associated with EAF dust management. The primary goal of the assessments was to identify and prioritize areas for potential improvement - either in environmental management systems area or the technology area. The assessment results showed that steel plants which have practices with lower values, according to these matrices, should require greater effort to improve their performance, while those with good score, will require a consolidation of their routine to maintain the high level of performance already achieved. The matrices were filled by environmental experts from three steelmaking companies. Finally, as a result of this project a rigorous and reliable assessment tool was designed to evaluate the meltshop dust generation and management process and provide a quantitative answer to the following question: `Which area has achieved a higher level of development as it relates to meltshop dust management: environmental management system practices or control technology?’ The results from using this tool have shown that the performance of management practices is superior to the control technology. Furthermore, experiences captured during the assessment indicate this evaluation methodology is fully adaptable and can be applied to other processes and/or other businesses. It was clearly highlighted how knowledge and environmental intelligence are requirements to assure that the medium and long term strategies are properly aligned with the available best practices to environmental management system and control technology.

Voltage fluctuations under 30 Hz in the electricity grid, leads to oscillations in the light intensity that can be perceived by human eye, which is called flicker. In this thesis, the sources of the flicker at a point of common coupling is investigated. When there are more than one flicker sources connected to a PCC, individual effects of each flicker source is determined by using a new method which depends on the reactive current components of the sources. This method is mainly based on the flickermeter design defined by the International Electrotechnical Commission (IEC), but uses the current variations in addition to the voltage variations to compute flicker. The proposed method is applied to several different types of loads supplied from a PCC and their flicker contributions on the busbar are investigated. Experiments are performed on field data obtained by the power quality analyzers (PQ+) developed by the National Power Quality Project and the method has been found to provide accurate results for flicker contributions of various loads. The PQ+ analyzers with the proposed flicker contribution detection algorithm are called Flicker Contribution Meters (FCM) and they will be installed at the points of the Turkish Electricity Transmission Network when required.