This thesis presents an investigation of the damping of spin waves in ferromagnetic Au(3 nm)/Ni(10 nm)/MgO(001) thin films using the time-resolved Magneto-optical Kerr Effect (TR-MOKE) and ferromagnetic resonance (FMR) techniques. In the optical measurements, a 150 fs, 800 nm laser beam pulse is split into pump and probe components. The pump pulse, containing most of the beam energy, thermally excites coherent spin precession. The weaker probe pulse, time-delayed by a variable beam path, captures the magnetization dynamics via the polar MOKE effect, and oscillations are observed as a function of external field amplitude and direction. The extracted precession frequency is consistent in both the optical and resonance techniques; however, additional damping is observed in the TR-MOKE measurements that is strongly correlated to the orientation of the magnetization with respect to the magnetic anisotropy. The damping is identical in TR-MOKE and FMR only when the external field is applied near the easy axis of magnetization. The enhanced damping in TR-MOKE is shown to be a consequence of pump-induced inhomogeneous broadening in the presence of magnetic anisotropy, a result of differing temperature recovery profiles for the magnetization and magnetic anisotropy. Finally, a simple model is developed which explains the anisotropic damping: mode broadening occurs in regions where the magnetization changes rapidly with respect to changes in the external field, as determined by the curvature of the magnetic free energy. We thus introduce a novel damping effect in TR-MOKE: pump-induced anisotropic damping (PIAD).

No description available.

Antenna systems play a significant role in today’s electronic communications. They are essential for cell phones, satellites, radio, and radar among many other important applications. This paper describes the design, assembly, and operation of an antenna demonstration system designed to instill interest in the field of antenna design among high school and undergraduate college students. The system is portable, supplied solely by DC power supplies, easily reproducible, and includes rotational axes to illustrate antenna performance limitations and requirements. It provides a visual indication of wireless signal strength and demonstrates several antenna performance characteristics including polarization, gain and directivity, radiation patterns - nulls and maximums, and spreading loss. Several antenna types used in present-day applications (embedded and reflector antennas), in addition to structural barriers encountered in typical operating environments, are used to define wireless system performance. Students gain insight on radiating structure and orientation effects on antenna system characteristics and hopefully develop interest in future wireless studies.

Swept Frequency Source Optical Coherence Tomography (OCT) requires high repetition rate and wide spectral width wavelength tunable sources at a low cost. The sampled grating distributed Bragg reflector (SG-DBR) laser provides wide wavelength tuning range while exhibiting a wavelength switching speed that is among the fastest currently available. The SG-DBR laser is used to generate linear frequency ramps with high repetition rates. Since the SG-DBR laser is currently used for the telecommunications industry in high volume, the price of the system is much lower than current OCT sources. Therefore the SG-DBR laser provides a practical solution for Swept Source OCT. Four synchronized waveforms sent to the inputs of the laser control the linear frequency ramp. Three of the waveforms control the output frequency, while the fourth waveform controls the output amplifier of the laser to keep the output power stable. Two SG-DBR lasers with overlapping wavelength coverage are also concatenated to increase the bandwidth of the swept frequency source. The linear ramp stitching points in the frequency ramps are investigated and methods are outlined to reduce them. Finally, experimental OCT tests are performed using the swept frequency sources created to analyze the linearity of our sources. From these test results, an evaluation can be made on the specifications and capabilities of the swept frequency sources and analyze their value for OCT applications.

From a very general perspective, optical devices can be viewed as constructions based on the spatial engineering of the optical index of refraction. Sculpting the real part of the refractive index produces the wide variety of known passive optical devices, such as waveguides, resonators, gratings, among a plethora of other possibilities for managing the transport of light. Less attention has been directed to engineering the imaginary part of the refractive index – that is responsible for optical gain and absorption – in conjunction with the real part of the refractive index. Optical gain is the building block of amplifiers and lasers, while optical absorption is exploited in photovoltaic devices, photodetectors, and as dopants in lasing media. Recently, the field of non-Hermitian photonics has emerged in which the new opportunities afforded by the spatial engineering of the optical gain and loss in an optical device are being exploited. Indeed, the judicious design of such active devices can result in counterintuitive physical effects, new optical functionalities that enable unexpected applications, and enhanced performance of existing devices. In this work, we have theoretically and experimentally demonstrated four different non-Hermitian arrangements exhibiting novel non-trivial features. First, we show that the direction of energy flow can be controlled inside an active cavity by tuning the optical gain. Reversing the direction of the energy flow within the cavity – such that Poynting's vector points backwards towards the source – takes place when the cavity gain exceeds a certain threshold value, which we have named 'Poynting's threshold'. To realize this effect, we have employed a fiber-based arrangement that allows for unambiguous determining of the direction of the energy flow within the cavity. Second, we have studied the implication of Poynting's threshold with respect to spectral reflection from an active cavity. Surprisingly, the reflection at Poynting's threshold becomes spectrally flat and is guaranteed to attain unity reflectivity while maintaining non-zero transmission. In other words, at Poynting's threshold, the cavity becomes a 'transparent perfect mirror'. We have realized this effect in an on-chip active waveguide device and in an optical-fiber-based system. Third, we have examined a parity-time (PT) symmetric fiber-based cavity consisting of two coupled sub-cavities, one of which contains gain and the other loss. In contrast to all previous on-chip PT-symmetric micro-devices, the exotic features of such a system may be expected to vanish when the length of the cavity is extremely large (exceeding 1 km in our experiments) due to the strong fluctuations in the optical phase. Nevertheless, we have found that some of the central features of such a system survive; e.g., loss-induced enhancement of lasing power is still observable. Finally, we have demonstrated – for the first time – the interferometric perfect absorption of light in a weakly absorbing (erbium-doped) fiber system. Additionally, we verified that this coherent effect is the most efficient configuration with respect to utilizing the absorbing species in the medium.

The solid-state laser is one of the most widely used lasers in scientific research and industrial applications. This thesis describes detailed investigations of two modern architectures of high power cw solid-state lasers, a 20 W diode-pumped Yb:YAG thin disc laser and 300 W diode-pumped Nd:YAG rod laser. With the thin disc laser architecture, the signal beam must fit to the pump area on the disc defined by the multi-pass diode pump configuration. The beam propagation, beam diameter, phase and thermal effects for various cavity configurations are investigated theoretically and experimentally. In addition, the internal loss, small signal gain, and thermal lensing effect are essential properties to construct the laser system but usually unknown. The theories and methodologies to obtain these properties are presented and the experimental results are compared. In a second phase of the project, the multi-mode and single-mode operation of a high power diode-pumped rod laser system are examined and compared to the thin disc system. Thermal effects on the phase, beam quality and brightness are examined and future applications and improvements considered.

The thesis reviews principle of laser cavity and gives a general introduction to modelocked laser (MLL). By using Yb3+-doped fiber as gain medium, passive MLL cavity is developed in experiment, aiming to obtain femtosecond pulses with high pump power from 25W to 35W. The gain medium fiber with 65µm core diameter is cleaved with one flat end and another angled. Pump laser with 976nm wavelength is coupled into Yb3+ -doped fiber to excite signal from 1020nm to 1040nm in the core. 9W is threshold for laser setup. After locking all modes, picosecond pulses are output from laser cavity and coupled into dispersion delay fiber. By compressing pulse width, pulses are in soliton mode and then femtosecond laser pulses are obtained pulses are obtained. To measure ultrafast pulse width effectively, an auto-correlator based on Mach–Zehnder interferometer is developed. In the receiver terminal, a photodiode with range 320 nm to 1000 nm is used to detect signal and two photon absorption (TPA) method is applied.

The radiation quality factor of small vertically polarized antennas above a ground plane is investigated. Although the quality factor of small antennas in free space has been investigated extensively in the past, the exact effect of a conducting ground plane on the antenna bandwidth is not clearly understood. In this thesis, quality factors of vertically polarized antennas above a ground plane are computed and compared with their free-space counterparts. The theoretical results on quality factors are validated with simulations of electrically small spherical helix antennas.

Implementation of high-performance photonic integrated devices and circuits is becoming a growing essential need for a plethora of classical and nonclassical applications such as, high-speed telecom and data-com systems, frequency metrology and quantum communication systems. These applications require a combination of linear optics (e.g., beam splitters and filters), fast modulation (e.g., electro-optic modulators) along with nonlinear optical processes. Thin-film lithium niobate (TFLN) stands as an ideal platform for that purpose due to its high electro-optic, nonlinear-optic, and ferroelectric effects, its wide transparency window, and its compatibility with fabrication technologies, especially, standard silicon photonics. This work aims at harnessing the unique properties of TFLN for implementation of high-performance integrated devices and circuits for nonlinear- and quantum-optic applications. First, we demonstrate thin-film periodically-poled lithium niobate (TF-PPLN) waveguides with the highest reported nonlinear conversion efficiency on TFLN to date. Then, we introduce a new class of wideband nonmagnetic and linear optical isolators, based on nonlinear frequency conversion and spectral filtering. We utilize TF-PPLN devices to experimentally demonstrate our novel isolator system with a wide bandwidth and high optical isolation ratio. We introduce and demonstrate efficient quantum-correlated photon-pair sources via nonlinearities in TF-PPLN waveguides. We also demonstrate tunable dual-channel ultra-narrowband Bragg grating filters on TFLN. All the demonstrated devices pave the path for implementation of high-performance advanced nonlinear and quantum photonic integrated circuits (PICs), as discussed in the future work directions.

This dissertation explores a new method for creating holographic phase masks (HPMs), which are phase transforming optical elements holographically recorded in photosensitive glass. This novel hologram recording method allows for the fast production of HPMs of any complexity, as opposed to the traditional multistep process, which includes the design and fabrication of a master phase mask operating in the UV region before the holographic recording step. We holographically recorded transmissive HPMs that are physically robust (they are recorded in a silicate glass volume), can handle tens of kilowatts of continuous wave (CW) laser power, are un-erasable, user defined, require no power to operate, can work over a wavelength band ranging from 350 to 2500 nm, and can modify the wavefront of narrow line or broad band coherent sources. The HPMs can be wavelength-tunable by angular adjustment over tens or even hundreds of nanometers. The HPMs incorporate the phase information in the bulk of a volume Bragg grating (VBG) resulting in only a single diffraction order and up to 100% diffraction efficiency. Recording in thick photosensitive medium also enables the multiplexing of HPMs in a single monolithic element. While these HPMs are physically overlapped in the space, they provide independent phase profiles, efficiencies, spectral and angular acceptances. Multiplexing HPMs allows splitting or combining of multiple beams while affecting their wavefronts individually. We also developed a new holographic phase mask of reflective-type. This device provides us the ability of recording RBGs with transversely shifted parts in the larger aperture which upon reconstruction will produce different phases to different parts of the diffracted beam. RBG's diffraction spectrum possesses a very narrow bandwidth, and the holographic recording technique allows to multiplex multiple gratings into a single volume of PTR glass. If each of these Bragg wavelengths is assigned with a specific spatial mode, it can be achieved simultaneous spatial and spectral multiplexing. As a separate research topic, we look at how holographic optical elements (HOEs) can be used for improving the capabilities of the existing generation of head-up displays (HUDs), resulting in smaller, lighter units with a larger eye-box. Currently, surface relief gratings recorded in photosensitive polymers that are susceptible to the environmental conditions are used in HOE-based HUDs. This has an impact on their reliability and overall lifespan. We investigated a specific holographically recorded in the volume of photo-thermo-refractive glass transmissive gratings that generated multiple diffracted beams due to their operation in Raman-Nath regime. The Raman Nath gratings were successfully used to create an array of images because in augmented reality systems, this approach can be used to enhance the size of the exit pupil. These image splitting elements, due to the features of PTR glass, have a great resistance to temperature gradients, mechanical shocks, vibrations, and laser radiation.