Thesis (Ph. D.)--University of Adelaide, Dept. of Civil Engineering, 1992. / Includes bibliographical references.

Thesis (Ph. D.)--University of Wollongong, 2005. / Typescript. Includes bibliographical references (leaf 241-251).

Thesis (Ph.D.)--University of Wollongong, 2006. / Typescript. Includes bibliographical references: leaf 191-207.

Thesis (Ph.D.) - University of Queensland, 2006. / Includes bibliography.

Thesis (MScIng)--University of Stellenbosch, 2005. / Bibliography. Also available via the Internet.

Ground improvement by deep mixing (DM) is a generic term used for a number of methods in which a binding agent, often lime and/or cement, is mechanically mixed with the soil to increase its engineering properties. The inherent variability with respect to the engineering properties of the improved soil is high due to the variations in geology and the complex mixing process. High variability introduces uncertainty in estimating improved soil properties and the performance of the structure. Current design methodology deals with soil properties deterministically and the uncertainties involved are incorporated in a single value represented by a total factor of safety (FS). The chosen FS is highly dependent on the engineer’s judgment and past experience, in which both of these factors vary between different geotechnical designers. Therefore, current design methodology used in practice for DM does not deal with uncertainties in a rational way. In order to design a geotechnical system with the desired level of confidence, the uncertainties involved must be integrated in the DM design. This can be achieved by using reliability-based design (RBD) methods. The research work in this thesis is presented as a collection of three papers. In the first paper, a comprehensive statistical analysis of cone penetration test (CPT) data is described. The objective was to make a contribution to empirical knowledge by evaluating the strength variability of lime-cement columns within the group of tested columns. In the second paper, the effect of the spatial variability and statistical uncertainty with regard to the embankment’s reliability was investigated within the framework of RBD. The study in the third paper investigated the strength variability in lime-cement columns based on two test methods, namely CPT and column penetration test (KPS). In this study, the effect of different test methods on the evaluation of the design value was addressed. The main conclusions from this study can be summarized as follows. First, the probability distribution function (PDF) for the undrained shear strength of lime-cement columns can be modeled in RBD as normal or log-normal distributions. However, the use of log-normal distribution is recommended for RBD analyses. Second, the evaluated scales of fluctuation indicate ranges of 2 to 4 m and 0.2 to 0.8 m in the horizontal and the vertical directions respectively. This means that in order to fulfill the requirements of independent/uncorrelated samples for assessment of the design value, the spacing between samples must exceed the horizontal scale of fluctuation. It is therefore proposed that the spacing between individual samples should be at least 4 meters. Third, the design values evaluated using CPT and KPS were approximately the same. However, the inherent variability evaluated differs due to the larger volume tested with the KPS probe than with the CPT probe. However, this difference was not significant between the two tests. Fourthly, due to the limitation in the deterministic design in terms of dealing with uncertainties, it is recommended that RBD design should be used in parallel with the deterministic design of lime-cement column. / <p>QC 20120110</p>

This study is a parametric evaluation of reduction in undrained shear strength of fine grained soils required to cause failure beneath embankments during earthquake loading. The evaluated parameters are: crust thickness, normalized undrained strength, maximum past pressure, and embankment height. Both finite element and limit equilibrium analyses were used to determine strength reductions that would lead to embankment failure. It was found that reductions of undrained strengths of 55% to 65% would lead to failure during earthquake loading. The method proposed by Idriss and Boulanger was also used to predict strength reductions for each model over a range of earthquake amplitudes and magnitudes. Idriss and Boulanger predicted strength reductions around 80% which would not lead to collapse of the embankments.

A project report submitted to the Faculty of Engineering, University of the Witwatersrand, Johannesburg, in partial fulfillment of the requirements for the degree of Master of Science in Engineering. / The project report deals with the relationship between the undrained shear strength and the moisture content of Red Berea sand tailings. The tailings were obtained from the Red Berea sand dunes near Richards Bay, Kwa-Zulu Natal, South Africa. The geology of the area consists of Miocene deposits of red clayey sand, classified as Berea Formation. A method for determining stability of a tailings dam for Red Berea sand tailings, was investigated. The general method of using the degree of saturation of the tailings to specify the rate of rise, is not applicable to this type of tailings. It was found that a relationship exists between the undrained shear strength of the tailings, and the moisture content. The moisture content can easily be measured and the undrained shear strength can then be calculated. The calculated undrained shear strength can be used in a total stress analysis to determine a factor of safety against failure. This project report consists of a discussion of the literature, which was used as the basis for the assumptions made, as well as a description of the tests performed to prove the above-mentioned relationship. Test results are given, interpreted and used in an illustrative example of a stability analysis. / Andrew Chakane 2020

Embankments are key elements in the infrastructural development of structures such as dams, bridges, and roads. Residual soils are generally used as fills in the construction of embankments in areas were residual soils such as laterite is the dominant soil types. Laterite soils have the characteristics of losing its shear strength with time and in fully saturated conditions and its properties varies from region to region. The soil property is influenced by the chemical composition and the environment. The binding agent iron oxide in such soils changes its composition with time and in the presence of moisture. Sudden failures of embankments founded of laterite soils which were, otherwise, checked and found to be safe with high factor of safety, have been observed. This study is performed to investigate the stability of embankments with sudden loss of strength with time and when it is fully saturated. The research includes an investigation of the properties of laterite soils around the world, with particular emphasis on Nigeria. Initially, information is gathered from different sources about the strength-based properties of such soils. Previous research in Nigeria is used as a basis for obtaining real-world soil data. Next, stability analyses are performed using SLOPE/W with shear strength parameters for total stress (short-term), effective stress (long-term), and fully saturated soil conditions. A probability analysis is conducted for the fully saturated conditions because of the variability in the input parameters. Three slope configurations (1:1, 2:1, and 3:1) are considered. The study revealed that the laterite soils embankments lose most of its stability over time period and in full saturation soil conditions. Both these conditions significantly compromise the strength of the soil and the related stability of slopes. To consolidate all information, a database of the properties of laterite soils in some localities of Nigeria was created on the geographic information system (GIS), in order provide a quick access to information on laterite soils in Nigeria.

The use of tensile reinforcement to increase the tensile strength and shear strength of soils has lead to many new applications of reinforced soil. The use of such reinforcing in embankments and foundations over weak soils is one of the most recent applications of this technology. The studies conducted were concerned with the development of and application of analytical techniques to reinforced soil foundations and embankments over weak soils. A finite element computer program was modified for application to reinforced soil structures, including consolidation behavior of the foundation soil. Plane strain and axisymmetric versions of the program were developed and a membrane element developed which has radial stiffness but no flexural stiffness. The applicability of the program was verified by comparing analytical results to case histories of reinforced embankments and to model studies of reinforced foundations. A simplified procedure for computing the bearing capacity of reinforced sand over weak clay was developed which is more general than those previously available. Good agreement with available experimental results was obtained, providing preliminary verification of the procedure. Extensive analyses were made of a reinforced embankment successfully constructed with no sign of distress, and of two reinforced embankments constructed to failure. These analyses showed that good agreement can be obtained between measured and calculated reinforcement forces, settlements, and pore pressures for both working and failure conditions. The analyses further show that the use of the finite element method and limit equilibrium analyses provide an effective approach for the design of reinforced embankments on weak foundations. / Ph. D. / incomplete_metadata