Being the major energy consumer of electricity and natural gas, buildings consume more than 70% of electricity and 30% of natural gas. On the way to green buildings and zero energy buildings, investigation and improvement of energy efficiency of the buildings will result in significant reductions in energy demands and CO2 emissions / make cost savings and improve thermal comfort as well. Key steps of a successful green, energy efficient building can be summarized as whole building design, site design, building envelope design, lighting and day lighting design and HVAC system design. Energy Plus&reg / software is mainly developed to simulate the performance of the buildings in the view of the above listed points. The design of a building or the analysis of an existing building with the software will show how efficient the building is or will be, and also helps finding the best efficient choice of the whole building system. Thesis focuses on the effect of changes in building envelope properties. In Turkey, topic of green buildings has recently started to be studied. Therefore, this thesis aims to present efficient technologies providing energy savings in buildings, to present green building concept and alternative energy simulation software. In the context of this study, design, methods and material guidelines are introduced to reduce energy needs of buildings and to bring in the green building design concept. Building and system parameters to enhance building energy efficiency and energy savings together with green building principles are summarized. Moreover, whole building energy analysis methods and simulation steps are explained / year-round simulation is performed for a sample building / as a result, energy savings about 36% is achieved.

The energy used in non-domestic buildings accounts for 18 % of the energy use in the UK. Within the non-domestic building stock, 11 % of office buildings have a very high influence on the energy use. Thus, the retrofit of office buildings has a significant potential for energy efficiency and greenhouse gas emissions reduction within the non-domestic building stock. However, the replacement rate of existing buildings by new-build is only around 1-3 % per annum. Post-war office buildings, (built between 1945 and 1985) represent a promising sector for retrofit and energy demand reduction. They have disproportionately high energy consumption because many were built before the building regulations addressed thermal performance. The aim of the research is to evaluate the retrofit strategies for post-war office buildings accounting for the improved energy efficiency, thermal comfort and hence, productivity, capital and the running costs. The research seeks to provide the optimal generic retrofit strategies and illustrate sophisticated methods which will be the basis for guidelines about post-war office building retrofit. For this, multiple combinations of heating and cooling retrofit measures were applied to representative models (Exemplar) of post-war office buildings using dynamic thermal simulation modelling. The retrofit strategies include; applying envelope retrofit to UK Building Regulations Part L2B and The Passivhaus Institue EnerPHit standards for heating demand reduction and winter comfort. Passive cooling interventions such as shading devices and night ventilation and active cooling intervention such as mixed-mode ventilation were applied to overcome summer overheating. All retrofit combinations were evaluated considering future climate, inner and outer city locations and different orientations. In summary, the results showed that under current weather conditions Part L2B standard retrofit with passive cooling provided the optimum solution. In 2050, however, both Part L2B retrofit naturally ventilated cases with the passive cooling measures and EnerPHit retrofit mixed-mode ventilation cases provide the requisite thermal comfort and result in a similar range of energy consumption. It was concluded that to create generic retrofit solutions which could be applied to a given typology within the building stock is possible. The methodology and the Exemplar model could be used in future projects by decision-makers and the findings and analysis of the simulations could be taken as guidance for the widespread retrofit of post-war office buildings.

abstract: The Urban Heat Island (UHI) has been known to have been around from as long as people have been urbanizing. The growth and conglomeration of cities in the past century has caused an increase in the intensity and impact of Urban Heat Island, causing significant changes to the micro-climate and causing imbalances in the temperature patterns of cities. The urban heat island (UHI) is a well established phenomenon and it has been attributed to the reduced heating loads and increased cooling loads, impacting the total energy consumption of affected buildings in all climatic regions. This thesis endeavors to understand the impact of the urban heat island on the typical buildings in the Phoenix Metropolitan region through an annual energy simulation process spanning through the years 1950 to 2005. Phoenix, as a representative city for the hot-arid cooling-dominated region, would be an interesting example to see how the reduction in heating energy consumption offsets the increased demand for cooling energy in the building. The commercial reference building models from the Department of Energy have been used to simulate commercial building stock, while for the residential stock a representative residential model prescribing to IECC 2006 standards will be used. The multiyear simulation process will bring forth the energy consumptions of various building typologies, thus highlighting differing impacts on the various building typologies. A vigorous analysis is performed to see the impact on the cooling loads annually, specifically during summer and summer nights, when the impact of the 'atmospheric canopy layer' - urban heat island (UHI) causes an increase in the summer night time minimum and night time average temperatures. This study also shows the disparity in results of annual simulations run utilizing a typical meteorological year (TMY) weather file, to that of the current recorded weather data. The under prediction due to the use of TMY would translate to higher or lower predicted energy savings in the future years, for changes made to the efficiencies of the cooling or heating systems and thermal performance of the built-forms. The change in energy usage patterns caused by higher cooling energy and lesser heating energy consumptions could influence future policies and energy conservation standards. This study could also be utilized to understand the impacts of the equipment sizing protocols currently adopted, equipment use and longevity and fuel swapping as heating cooling ratios change. / Dissertation/Thesis / M.S. Architecture 2011

Natural disasters are affecting a significant number of people around the world. Sheltering is the first step in post-disaster activities towards the normalization of the affected people's lives. Temporary housing is being used in these cases until the construction of permanent houses are done. Disposal of temporary housing after use is leading to a significant environmental impact because most of them are filled with thermally insulative polymer foams that do not degrade in a short period. To reduce these problems this work proposes to use foams made with compostable thermoplastic polylactic acid (PLA) and degradable kenaf core as filler materials; these foams are made using CO2 as blowing agent for insulation purposes. Foams with PLA and 5%, 10% and 15% kenaf core were tested. Different properties and their relations were examined using differential scanning calorimetry (DSC), thermal conductivity, mechanical properties, scanning electron microscopy (SEM), x-ray μ-computed tomography (μ-CT) and building energy simulations were done using Energy Plus by NREL. The results show that mechanical properties are reduced with the introduction of kenaf core reinforcement while thermal conductivity display a noticeable improvement.