Spelling suggestions: "subject:"engine old start"" "subject:"engine old mtart""
1 |
Comparative non-linear simulation of temperature profiles induced in an exhaust manifold during cold-startingDesai, D.A. January 2010 (has links)
Published Article / The simulation of an exhaust manifold's thermal behaviour is an important concern for various reasons. Amongst them is the need to minimise catalyst light-offtime as significant exhaust emissions are generated within this period. Modelling such behaviour is not simplistic as it is governed by complex interactions between exhaust gas flow and the manifold itself. Computational fluid dynamics (CFD) is a powerful tool for such simulations. However its applicability for transient simulations is limited by high central processing unit (CPU) demands. The present study proposes an alternative computational method to assess and rank the relative impact of the manifold's thermal properties on its exterior temperature. The results show that stainless steel manifolds potentially minimise heat loss from the exhaust gas when compared with their cast iron counterparts. This may result in an increase in thermal energy being available to heat the catalyst.
|
2 |
An optical investigation of DISI engine combustion, fuel spray and emissions at cold-start temperaturesEfthymiou, Petros January 2015 (has links)
Particulate number (PN) standards in current and future emissions legislation pose a challenge for designers and calibrators during the warm-up phases of cold direct injection spark ignition (DISI) engines. To achieve catalyst light-off conditions in the shortest time, engine strategies are often employed that inherently use more fuel to attain higher exhaust temperatures. These can lead to the generation of locally fuel-rich regions within the combustion chamber and hence the formation and emission of particulates. To meet these emissions requirements, further understanding of the DISI in-cylinder processes during cold-start are required. This thesis investigates the effect of cooling an optical research engine to temperatures as low as -7°C, one of the legislative test conditions. A high-speed 9 kHz optical investigation of the in-cylinder combustion and fuel spray along with in-cylinder pressure measurements was completed with the engine motored and fired at 1500 rpm during combustion conditions that were essentially homogeneous and stoichiometric. Results showed significant differences between the flame growth structures at various operating temperature conditions with the notable presence of fuel-rich regions, which are understood to be prominent areas of particulate formation. Measured engine performance parameters such as indicated mean effective pressure (IMEP) and mass fraction burned (MFB) times correlated with the observed differences in combustion characteristics and flame growth speed. It was shown that flash boiling of the fuel spray was present in the fully heated engine case and significantly reduced the penetration of the spray plume and the likelihood of piston crown and cylinder liner impingement. The flow and combustion processes of a transient production cold start-up strategy were analysed using high-speed particle image velocimetry (HSPIV). Results highlighted a broad range of flame structures and contrasting flame stoichiometry occurring at different times in the start-up process. Turbulent flow structures were identified that have an effect on the fuel spray development and combustion process as well as providing a path for cold-start emissions reduction. PN and transient hydrocarbon (HC) emissions were measured at cold conditions to further elucidate the effect of operating temperature and correlate emissions data with in-cylinder measurements. A clear link between the quantity and size range of particulate and HC emissions and operating temperature was shown and the precise in-cylinder location of HC emissions, caused by fuel impingement, was inferred from the HC emissions data.
|
3 |
Modeling Light Duty Vehicle Emissions Based on Instantaneous Speed and Acceleration LevelsAhn, Kyoungho 23 July 2002 (has links)
This dissertation develops a framework for modeling vehicle emissions microscopically. In addition, the framework is utilized to develop the VT-Micro model using a number of data sources. Key input variables to the VT-Micro model include instantaneous vehicle speed and acceleration levels. Estimating accurate mobile source emissions is becoming more and more critical as a result of increasing environmental problems in large metropolitan urban areas. Current emission inventory models, such as MOBILE and EMPAC, are designed for developing large scale inventories, but are unable to estimate emissions from specific corridors and intersections. Alternatively, microscopic emission models are capable of assessing the impact of transportation scenarios and performing project-level analyses.
The VT-Micro model was developed using data collected at the Oak Ridge National Laboratory (ORNL) that included fuel consumption and emission rate measurements (CO, HC, and NOx) for five light-duty vehicles (LDVs) and three light-duty trucks (LDTs) as a function of the vehicle's instantaneous speed and acceleration levels. The hybrid regression models predict hot stabilized vehicle fuel consumption and emission rates for LDVs and LDTs. The model is found to be highly accurate compared to the ORNL data with coefficients of determination ranging from 0.92 to 0.99. The study compares fuel consumption and emission results from MOBILE5a, VT-Micro, and CMEM models. The dissertation presents that the proposed VT-Micro model appears to be good enough in terms of absolute light-duty hot stabilized normal vehicle tailpipe emissions. Specifically, the emission estimates were found to be within the 95 percent confidence limits of field data and within the same level of magnitude as the MOBILE5a model estimates. Furthermore, the proposed VT-Micro model was found to reflect differences in drive cycles in a fashion that was consistent with field observations. Specifically, the model accurately captures the increase in emissions for aggressive acceleration drive cycles in comparison with other drive cycles.
The dissertation also presents a framework for developing microscopic emission models. The framework develops emission models by aggregating data using vehicle and operational variables. Specifically, statistical techniques for aggregating vehicles into homogenous categories are utilized as part of the framework. In addition, the framework accounts for temporal lags between vehicle operational variables and vehicle emissions. Finally, the framework is utilized to develop the VT-Micro model version 2.0 utilizing second-by-second chassis dynamometer emission data for a total of 60 light duty vehicles and trucks.
Also, the dissertation introduces a procedure for estimating second-by-second high emitter emissions. This research initially investigates high emitter emission cut-points to verify clear definitions of high emitter vehicles (HEVs) and derives multiplicative factors for newly developed EPA driving cycles. Same model structure with the VT-Micro model is utilized to estimate instantaneous emissions for a total of 36 light duty vehicles and trucks.
Finally, the dissertation develops a microscopic framework for estimating instantaneous vehicle start emissions for LDVs and LDTs. The framework assumes a linear decay in instantaneous start emissions over a 200-second time horizon. The initial vehicle start emission rate is computed based on MOBILE6's soak time function assuming a 200-second decay time interval. The validity of the model was demonstrated using independent trips that involved cold start and hot start impacts with vehicle emissions estimated to within 10 percent of the field data.
The ultimate expansion of this model is its implementation within a microscopic traffic simulation environment in order to evaluate the environmental impacts of alternative ITS and non-ITS strategies. Also, the model can be applied to estimate vehicle emissions using instantaneous GPS speed measurements. Currently, the VT-Micro model has been implemented in the INTEGRATION software for the environmental assessment of operational-level transportation projects. / Ph. D.
|
Page generated in 0.0922 seconds