Spelling suggestions: "subject:"engineering - 1design anda construction"" "subject:"engineering - 1design ando construction""
1 |
Probabilistic distributions of ultimate axial pile resistance derived from propagation of epistemic and aleatory material and model uncertaintiesSaussus, Denis 08 1900 (has links)
No description available.
|
2 |
Design and construction related defects of large diameter bored piles,prevention and remedial measuresLuk, Ka-sing., 陸家聲. January 2004 (has links)
published_or_final_version / Applied Geosciences / Master / Master of Science
|
3 |
Mini piles design and construction in current engineering practiceYiu, Wai-kei, Ricky., 姚偉基. January 2001 (has links)
published_or_final_version / Applied Geosciences / Master / Master of Science
|
4 |
Automated design of composite plates for improved damage toleranceGürdal, Zafer January 1985 (has links)
An automated procedure for designing minimum-weight composite plates subject to a local damage constraint under tensile and compressive loadings has been developed. A strain based criterion was used to obtain fracture toughness of cracked plates under tension. Results of an experimental investigation of the effects of simulated through-the-thickness cracks on the buckling, postbuckling, and failure characteristics of composite flat plates are presented. A model for kinking failure of fibers at the crack tip was developed - for compression loadings. A finite element program based on linear elastic fracture mechanics for calculating stress intensity factor (SIF) was incorporated in the design cycle. A general purpose mathematical optimization algorithm was used for the weight minimization. Analytical sensitivity derivatives of the SIF, obtained by employing the adjoint variable technique, were used to enhance the computational efficiency of the procedure. Design results for both unstiffened and stiffened plates are presented. / Ph. D.
|
5 |
High-level synthesis for dynamically reconfigurable systems. / CUHK electronic theses & dissertations collectionJanuary 1999 (has links)
by Xue-jie Zhang. / "December 1999." / Thesis (Ph.D.)--Chinese University of Hong Kong, 1999. / Includes bibliographical references (p. 144-[152]). / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Mode of access: World Wide Web. / Abstracts in English and Chinese.
|
6 |
Partial interaction behaviour of bolted side plated reinforced concrete beamsYuan, Lie Ping. January 2003 (has links) (PDF)
Includes bibliographical references (p. 185-189) Aims to determine the effect of partial interaction on the behaviour of the concrete beam, plate and bolt connector components of the composite plated beam. Develops design rules for the determination of the ultimate capacity for bolted plate reinforced composite beams.
|
7 |
Partial interaction behaviour of bolted side plated reinforced concrete beams / by Lie Ping Yuan.Yuan, Lie Ping January 2003 (has links)
Includes bibliographical references (p. 185-189) / xxviii, 207 p. : ill. ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Aims to determine the effect of partial interaction on the behaviour of the concrete beam, plate and bolt connector components of the composite plated beam. Develops design rules for the determination of the ultimate capacity for bolted plate reinforced composite beams. / Thesis (Ph.D.)--University of Adelaide, School of Civil and Environmental Engineering, 2003
|
8 |
Design of automotive joints: using optimization to translate performance criteria to physical design parametersZhu, Min 06 June 2008 (has links)
In the preliminary design stage of a car body, targets are first set on the performance characteristics of the overall body and its components using optimization and engineering judgment. Then designers try to design the components to meet the determined performance targets and keep the weight low using empirical, trial-and-error procedures. This process usually yields poor results because it is difficult to find a good design that satisfies the targets using trial-and-error and there might even be no feasible design that meets the targets. To improve the current design process, we need tools to link the performance targets and the physical design parameters.
A methodology is presented for developing two such tools for design guidance of joints in car bodies. The first tool predicts the performance characteristics of a given joint fast (at a fraction of a second). The second finds a joint design that meets given performance targets and satisfies packaging and manufacturing constraints. These tools can be viewed as translators that translate the design parameters defining the geometry of a joint into performance characteristics of that joint and vice-versa.
The methodology for developing the first translator involves parameterization of a joint, identification of packaging, manufacturing and styling constraints, and establishment of a neural network and a response surface polynomial to predict the performance of a given joint fast (at a fraction of a second). The neural network is trained using results from finite element analysis of several joint designs. The second translator is an optimizer that finds the joint with the smallest mass that meets given performance targets and satisfies packaging, manufacturing and styling constraints.
The methodology is demonstrated on a joint of an actual car. / Ph. D.
|
9 |
Virtual prototyping of an articulated dump truck.Govender, Deena. January 2003 (has links)
In the modem automotive industry product times to market are being increasingly compressed. In the earthmoving and construction machine industry this is also true with the manufacturer having to respond to new customer requirements quickly and decisively. Virtual prototyping is a vital tool in the vehicle engineer's armoury, allowing a large portion of developmental investigation to be done on the virtual model with the attendant savings in time and cost and allowing often dangerous manoeuvres to be predicted and investigated prior to actual physical prototype testing. The University of Natal BELL Equipment collaborative effort involves the vehicle dynamics modelling and model validation of a BELL Equipment manufactured B40C Articulated Dump Truck (ADT). The modelling was completed using the multibody system (MBS) simulation software package, ADAMS. Initial modelling and simulation results are presented with specific attention paid to the introduction of valid data for compliant joints in the MBS as well as modelling of the tire. The physical testing of the ADT is also presented as well as a discussion of the data acquisition system. Key results from the physical testing of the ADT are also presented and discussed. / Thesis (M.Sc.Eng.)-University of Natal,Durban, 2003.
|
10 |
New Approaches to Analyze Sound Barrier EffectivenessBeale, Michael P. 08 1900 (has links)
Indiana University-Purdue University Indianapolis (IUPUI) / Highway noise can cause annoyance, affect sleep patterns, and reduce the property value for people in the proximity. Current methods for analyzing the effectiveness of sound barriers only take loudness into consideration. This paper introduces new methods that can be used to analyze the effectiveness of the sound barriers. Our approach uses psychoacoustic measures including sharpness, roughness, fluctuation, strength, and annoyance. Highway noise is non-stationary, therefore each of these metrics are calculated over a short time. Finally analysis is performed the distribution and change over time. We used nth nearest neighbor algorithm to remove sounds that are not a part of the experiment. In the future, this data can be combined with human surveys to see if the change in sound quality due to the presence of sound barriers has a meaningful impact on people's lives.
|
Page generated in 0.1747 seconds