The service life of rigid sewer pipes is often controlled by joint integrity. Leaking joints can cause ingress of water and develop voids where surrounding soil has eroded. The influence of soil voids on the stability of buried rigid pipes is investigated, considering the effects of void size, void location and void shape. A series of simplified void geometries are defined, and their influence on bending moments in the rigid sewer is studied through finite element analysis. Elastic analysis indicates that the bending moments from expanding voids at the springline will increase slowly, accelerating once the void spans a 45 degree arc, approximately doubling at 90 degrees, and tripling if the loosened backfill is modeled for shear failure. This preliminary study suggests that the growth of erosion voids should be stopped before they reach 45 degrees, but validation through physical testing is necessary. Elastic-plastic finite element analysis is used to calculate the deformation of rigid fractured pipe with different thicknesses, considering both bonded and full-slip interface conditions. The analysis confirms that bonded idealized flexible pipe theory is very effective for calculation of increases in horizontal diameter of the fractured pipe. Furthermore, decreases in vertical diameter can be simply related to increase in horizontal diameter using (1-2t/OD) obtained from fractured pipe kinematics. Both elastic and elastic-plastic finite element analyses used to study the deformations of fractured rigid pipe reveal that contact angle appears to be the dominant factor affecting fractured pipe deformations. Deformation of the damaged rigid pipe increases dramatically with void growth and accelerates when erosion void contacts with the outer surface of the pipe over an arc greater than 45 degrees. Computational analyses examine the behavior of centrifuge model tests which examine soil load transfer to flexible sewer liners after fracture and erosion voids form nearby. The magnitude of deformation changes for finite element models is found to be comparable to observations when voids are formed at springline. However the development patterns are dramatically different as voids located under the invert, and it appears that the laboratory test featured physical characteristics that are not modeled in the analysis. / Thesis (Master, Civil Engineering) -- Queen's University, 2007-09-24 20:33:29.689

Yes / In this study, large-scale fully instrumented laboratory tests were conducted to investigate the behaviour of buried flexible high-density polyethylene (HDPE) pipes, in sand beds with and without voids subjected to incrementally increasing cyclic loading. Voids with a predetermined size were created at one side of the springlines of the pipes, which were buried at variable depths, H, of 1.5, 2.0 and 2.5 times the diameter of the pipe, D. Results showed that increasing the pipe burial depth, H/D, contributed to decreasing the settlement of the footing, deformation of the pipe crown and invert, lateral displacement of the spring-line, and the stress and strain generated along the pipe crown and invert. Void presence led to a significant increase in the footing settlement, which ranged from 3 % up to 18 %, according to H/D. Furthermore, void presence led to a sharp increase in the crown, invert, and spring-line settlements, which ranged from 34 % to 52 %, 10 %–12.5 %, and 13 %–38 %, respectively. Increasing pipe burial depth was found to be highly effective in protecting buried pipes, minimising inevitable consequences of the presence of voids. However, this was combined with an increase in the pressure at the pipe spring-line that led to a positive horizontal support at the pipe’s spring-lines resulting in reducing pipe deformation.

Protection of buried pipes is a serious issue that concerns countries around the world. Therefore, there is a need for new soil improvement techniques such as geosynthetic materials installation to protect these pipes from damage. This study used large-scale laboratory tests to study the behaviour of buried pipes. A total of 22 large-scale tests were performed to study the behaviour of buried flexible HDPE pipes with and without void presence under the protection of the geogrid reinforcing layers subjected to incrementally increasing cyclic loading. The presence of voids located at the spring-line of the flexible buried pipes, led to a considerable increase in the soil surface settlement, pressure recorded at the pipe crown, spring-line and invert, pipe deformation and strain recorded in the pipe wall. Increasing the pipe burial depth contributed to significant reductions in the soil surface settlement, pressure recorded at the pipe crown and invert, pipe deformation and strain recorded in the pipe wall. However, the void presence limited the contribution of increasing the pipe burial depth. The inclusion of a geogrid reinforcing layer contributed to a considerable reduction in the soil surface settlement, pressure recorded at the pipe crown, spring-line and invert, pipe deformation and strain recorded in the pipe wall. The use of a combination of geogrid reinforcing layers and increasing the pipe burial depth contributed in diminishing the ground void presence effect, where better pressure distribution inside the system was achieved. Consequently, more protection was provided to the buried pipe.