The work described in the thesis seeks to lay a foundation for a better understanding of the use of electrospun nanofibers as a sorbent material. Three miniaturised electrospun nanofiber based solid phase extraction devices were fabricated. For the first two, 10 mg of electrospun polystyrene fibers were used as a sorbent bed for a micro column SPE device (8 mm bed height in a 200 μl pipette tip) and a disk (I) SPE device (5 mm 1 mm sorbent bed in a 1000 μl SPE barrel). While for the third, 4.6 mg of electrospun nylon nanofibers were used as a sorbent bed for a disk (II) SPE device, (sorbent bed consisting of 5 5 mm 350 μm stacked disks in a 500 μl SPE barrel). Corticosteroids were employed as model analytes for performance evaluation of the fabricated SPE devices. Quantitative recoveries (45.5-124.29 percent) were achieved for all SPE devices at a loading volume of 100 μl and analyte concentration of 500 ng ml-1. Three mathematical models; the Boltzmann, Weibull five parameter and the Sigmoid three parameter were employed to describe the break through profiles of each of the sorbent beds. The micro column SPE device exhibited a breakthrough volume of 1400 μl, and theoretical plates (7.98-9.1) while disk (I) SPE device exhibited 400-500 μl and 1.39-2.82 respectively. Disk (II) SPE device exhibited a breakthrough volume of 200 μl and theoretical plates 0.38-1.15. It was proposed that the formats of future electrospun nanofiber sorbent based SPE devices will be guided by mechanical strength of the polymer. The study classified electrospun polymer fibers into two as polystyrene type (relatively low mechanical strength) and nylon type (relatively high mechanical strength).

This thesis presents the development of chlorophyll, cholic acid, aflatoxin B1 molecularly imprinted polymer (MIP) particles and cholic acid MIP nanofibers for application as selective solid phase extraction (SPE) sorbents. The particles were prepared by bulk polymerization and the nanofibers by a novel approach combining molecular imprinting and electrospinning technology. The AFB1 MIP particles were compared with an aflatoxin specific immunoextraction sorbent in cleaning-up and pre-concentrating aflatoxins from nut extracts. They both recorded high extraction efficiencies (EEs) of > 97 % in selectively extracting the aflatoxins (AFB1, AFB2, AFG1 and AFG2). High reproducibility marked by the low %RSDs of < 1% and low LODs of ≤ 0.02 ng/g were calculated in all cases. The LODs were within the monitoring requirements of the European Commission. The results were validated with a peanut butter certified reference material. The chlorophyll MIP on the other hand selectively removed chlorophyll that would otherwise interfere during pesticide residue analysis (PRA) from > 0.6 to <0.09 Au in green plants extracts. The extracted chlorophyll was removed to far below the level of ≥ 0.399 Au that is usually associated with interference during PRA. Furthermore, the MIP demonstrated better selectivity by removing only chlorophyll (> 99%) in the presence of planar pesticides than the currently employed graphitized carbon black (GCB) that removed both the chlorophyll (> 88%) and planar pesticides (> 89%). For the interfering cholic acid during drug residue analysis, cholic acid MIP electrospun nanofibers demonstrated to be more sensitive and possessing higher loading capacity than the MIP particles. 100% cholic acid was removed by the nanofibers from standard solutions relative to 80% by the particles. This showed that the nanofibers have better performance than the micro particles and as such have potential to replace the particle based SPE sorbents that are currently in use. All the templates were optimally removed from the prepared MIPs by employing a novel pressurized hot water extraction template removal method that was used for the first time in this thesis. The method employed only water, an environmentally friendly solvent to remove templates to ≥ 99.6% with template residual bleeding of ≤ 0.02%.

M.Tech. / Essential oils are volatile oils, generally odorous, which occur in certain plants or specified parts of plants, and are recovered by accepted procedures, such that the nature and composition of the product is, as nearly as practicable, unchanged by such procedures (ISO, 1968). The principal uses are as: flavouring agent, medicinal and aromatherapy application. Today, the essential oils are sought-after for innumerable applications starting from markers for plant identifications to bases for semi-synthesis of highly complex molecules. The extraction of highly delicate essential oils from plants remains a crucial step in all these applications. By using steam to mediate the extraction, it is possible to maintain mild conditions and effect superior extraction. In the current work, an integrated procedure for steam extraction followed by volatiles sampling and analysis from the leaves of the Eucalyptus tree was explored. There are two problems to overcome in the extraction from solid plant materials: that of releasing the essential oils from solid matrix and letting it diffuse out successfully in a manner that can be scaled-up to industrial volumes. Towards this end, the effect of different parameters, such as temperature, pressure and extraction time on the extraction yield was investigated and the experimental results show that all of these temperatures (90 °C, 97°C, and 99°C), were significant parameters affecting yield. Increase in yield was observed as pressure was increased and the use of high pressure (150 kPa) in steam extraction units permits much more rapid and complete distillation of essential oils over atmospheric pressure. The yield was calculated from the relation between the essential oil mass extracted and the raw material mass used in the extraction. The volatiles, Eucalyptus oil in vapour form released from the leaves were condensed and analyzed using Gas chromatography, and eight major components were found to be contained in this species. A mathematical model based on diffusion of essential oil from the leaves was developed. Using a numerical method, the best diffusion coefficient was established for different operating conditions by comparing the model concentration of oil remaining in the leaves with the experimental amount of oil recovered; hence minimizing the sum of squared errors. It was found that one cannot simply assume that the oil leached and recovered was the same as that originally present in the leaves. The initial mass of oil was determined by fitting the diffusion model to the data. An Arrhenius model was used to account for the effect of temperature. The resulting expression for the diffusion coefficient as a function of temperature can now be used to model the large scale extraction of the essential oils from Eucalyptus leaves.

Lysophosphatidic acid (LPA) influences many physiological processes, such as brain and vascular development. It is associated with several diseases including ovarian cancer, breast cancer, prostate cancer, colorectal cancer, hepatocellular carcinoma, multiple myeloma atherosclerotic diseases, cardiovascular diseases, pulmonary inflammatory diseases and renal diseases. LPA plasma and serum levels have been reported to be important values in diagnosing ovarian cancer and other diseases. However, the extraction and quantification of LPA in plasma are very challenging because of the low physiological concentration and similar structures of LPA to other phospholipids. Many previous studies have not described the separation of LPA from other phospholipids, which may make analyses more challenging than necessary. We developed an SPE extraction method for plasma LPA that can extract LPA at high purity. We also developed an HPLC post-column fluorescence detection method that allows the efficient quantification of LPA. These methods were used in a clinical study for ovarian cancer diagnosis to help validate LPA as a biomarker of ovarian cancer. Moreover, molecular imprinted polymers (MIPs) were designed and synthesized as material for the improved extraction of LPA. Compared to the commercially available materials, the MIP developed shows enhanced selectivity for LPA. The extraction was overall relatively more efficient and less labor-intensive.

Indiana University-Purdue University Indianapolis (IUPUI) / Organic-rich substrates such as soil provide an excellent carbon source for bacteria. However, hydrocarbons such as those found in various ignitable liquids can also serve as a source of carbon to support bacterial growth. This is problematic for fire debris analysis as samples may be stored at room temperature for extended periods before they are analyzed due to case backlog. As a result, selective loss of key components due to bacterial metabolism can make identifying and classifying ignitable liquid residues by their chemical composition and boiling point range very difficult. The ultimate goal of this project is to preserve ignitable liquid residues against microbial degradation as efficiently and quickly as possible. Field and laboratory studies were conducted to monitor microbial degradation of gasoline and other ignitable liquids in soil samples. In addition to monitoring degradation in potting soil, as a worst case scenario, the effect of soil type and season were also studied. The effect of microbial action was also compared to the effect of weathering by evaporation (under nitrogen in the laboratory and by the passive headspace analysis of the glass fragments from the incendiary devices in the field studies). All studies showed that microbial degradation resulted in the significant loss of n-alkanes and lesser substituted alkylbenzenes predominantly and quickly, while more highly substituted alkanes and aromatics were not significantly affected. Additionally, the residential soil during the fall season showed the most significant loss of these compounds over the course of 30 days. To combat this problem, a chemical solution is to be immediately applied to the samples as they are collected. Various household and commercial products were tested for their efficacy at low concentrations to eliminate all living bacteria in the soil. Triclosan (2% (w/v) in NaOH) proved to be the most effective at preserving ignitable liquid residues for at least 30 days.