The most common strategy for handling paper mill solid waste is typically disposal in landfills. However, several drawbacks are associated with this type of solid waste management, such as increasing costs due to oil price rise, governmental restrictions on land use, and environmental concerns such as leaching of disposed contaminants into groundwater, as well as methane generation of and release to the atmosphere, thus contributing to global warming. An alternative to reduce solids prior to disposal and to recover methane as a renewable fuel is anaerobic digestion, but it is not yet clear whether such an approach is feasible in paper mills. In this study, the anaerobic digestion of paper mill waste streams was evaluated for a paper plant located in Belen, Costa Rica, to investigate up to what extent certain waste streams can be anaerobically digested, to what extent energy can be produced in the form of methane for implementation in a wastewater treatment plant and to evaluate the conditions that will favor methane generation from select waste streams. Batch assays were performed to evaluate the biodegradability of single and combined waste samples under ideal, laboratory conditions. Samples were obtained from the manufacturing plant as well as the wastewater treatment plant at the paper mill under study. The ultimate biodegradability ranged 25 to 85% in terms of volatile solids destruction, corresponding to the waste activated sludge (WAS) and Flotation Cell rejects, respectively. The COD destruction of single samples ranged from 45 to 63%, corresponding to WAS and wastewater treatment plant (WWTP) dissolved air flotation (DAF) skimmings, respectively. Methane generation ranged from 80 to 190 ml at 35oC/g COD added for all single samples (excluding underflows). In combination Feed 1 was reduced by 46 and 52% and Feed 2 by 27 and 38%, respectively. Two combinations of two single samples each (Feed 1 and 2), formulated according to plant operational data, and their solids and COD destruction as well as methane generation in semicontinuous flow anaerobic digesters were evaluated at different solids retention times (30, 20, 15, and 7 days). Nutrients (N, and P) availability as well as alkalinity in the plant waste streams were evaluated and minimum supplements were used to support an efficient anaerobic digestion process. The reactors reached stable operation at all retention times evaluated. Methanogenesis was the predominant, terminal metabolic process under anaerobic, mesophilic conditions, but the overall process rate was determined by the hydrolysis of the particulate substrate. Reactors fed with Feed 1 achieved the highest level of destruction, which amounted to 85% of phosphorus that is typically present in paper mill wastes. Alkalinity addition to the feed (3.5 mg NaHCO3/L) was necessary to maintain the reactors pH above 6.9.

Phytosterols are naturally occurring compounds which regulate membrane fluidity and serve as hormone precursors in plants. They also have the potential to cause endocrine disturbances in aquatic animals at concentrations as low as 10 µg/L. Wastewaters from several industries which process plant matter can contain phytosterols at concentrations in excess of the above-stated level. Despite their endocrine disruption potential, very little is known about phytosterol physical properties and their biotransformation potential in biological treatment systems. Aerated stabilization basins (ASBs) are common biological treatment systems in North American pulp and paper mills. ASBs are large open lagoons which use tapered surface aeration to remove COD and prevent sulfate reduction in the water column. Phytosterols are released from wood during the pulping process and a small fraction enters the wastewater stream during washing of the pulp. Therefore, phytosterols may be exposed to aerobic or anaerobic environments depending on their solubility and solid-liquid partitioning behavior. The overall objective of this research was to systematically and quantitatively assess the biotransformation potential of phytosterols in biological treatment systems and to examine conditions leading to reduction of these compounds in wastewater effluent streams. The results of this research showed that phytosterols are sparingly soluble with aqueous solubility below 1 µg/L when present as a mixture. Phytosterols have a strong affinity to adsorb to solids and dissolved organic matter. The affinity for aerobic biomass was greater than for wastewater solids. The stigmasterol desorption rate and extent from wastewater solids increased with an increase in pH from 5 or 7 to 9. Phytosterols were biotransformed under aerobic conditions but not under sulfate-reducing or methanogenic conditions by stock cultures developed in this study. Biotransformation under nitrate-reducing conditions could not be confirmed conclusively. The continuous-flow system was successful in removing 72 to 96% of phytosterols. Biotransformation accounted for 23, 14 and 41 % of campesterol, stigmasterol and β-sitosterol removal, respectively. Phytosterols accumulated in the reactor sediment and accounted for 97 % of the total phytosterols remaining in the system. Phytosterols can be removed from wastewater streams during biological treatment by a combination of biotransformation and solids partitioning and control of system pH, DO and available carbon and energy sources can increase the degree of phytosterols removal. The results of this research can be used to engineer effective biological treatment systems for the removal of phytosterols from pulp mill wastewaters and other phytosterol-bearing wastewater streams.

The sugar refinery process used by Lantic Sugar Ltd generates three by-products having characteristics that give them potential as soil amendments or fertilizers, particularly as a phosphorous and calcium source. Laboratory and a field trials were conducted in order to examine the changes in agronomic properties of soil produced by the application of these residues. / During the laboratory experiment, the by-products examined were spend bone char (SBC), filter-press mud (FPM), clarification scum (SCU) and a compost (COM) produced using FPM and SCU, where as in a field experiment, COM, SBC and a mixture (MIX) made of FPM and SCU, were compared to a commercial fertilizer (TSP) and non-treated soils. / The orthic humic gleysol of clay texture and low pH soil conditions in which the field experiment was conducted resulted in high P fixation of all the applied residues. Contrasts analysis showed that TSP behaved as the soils unamended P for all nutrient concentrations in tissues over two cropping seasons (1993 and 1994), on two crops, namely wheat (Triticum aestivum, L.) and corn (Zea mays, L.). Treatments (residues at different rates of application) did not significantly increase the Ca levels in COM plots nor did they increase the wet aggregate stability of soil under either crop. (Abstract shortened by UMI.)

Fertilizer P fixation and fertilizer N losses in soils may be reduced through additions of polyphenolic compounds. The influence of ammonium lignosulfonate (NH$ sb4 sp+$-LS) on triple superphosphate (TSP) efficiency was investigated in a soil incubation study using three Quebec soils and in a growth bench study using one soil. For the incubation study, soils were analyzed for pH and P extractability, as a function of NH$ sb4 sp+$-LS rate and time. In the growth bench study, TSP and NH$ sb4 sp+$-LS were applied at varying rates and corn (Zea mays L.) dry matter yields and nutrient compositions analyzed. Similar studies were conducted in subsequent growth bench studies, to evaluate combinations of NH$ sb4 sp+$-LS, diammonium phosphate (DAP), and urea on two soils. / Ammonium LS increased soluble P levels when applied with TSP. The effect was most significant in fine textured soils, and increased with time. This improved P availability to plants, without affecting growth. The optimum NH$ sb4 sp+$-LS:P$ sb2$O$ sb5$ application ratio was approximately 2.8:1. Ammonium LS did not improve availability of DAP-P in either of the subsequent experiments, nor did it improve urea fertilizer efficiency. Some NH$ sb4 sp+$-LS-urea-DAP formulations did, however, improve corn growth beyond that obtained when only urea and DAP were applied in combination. In nutrient amended soils, applying NH$ sb4 sp+$-LS DAP was detrimental to growth and, for some application rates, reduced nutrient uptake.

Submitted in partial fulfillment of academic requirements for the degree of Masters of Technology: Department of Chemical Engineering, Durban University of Technology, 2009. / The primary objective of this project was to establish a screening protocol which could be used to access high strength/toxic effluent for toxicity and degradability prior to being disposed in wastewater treatment works. The serum bottle method (materials and method section) is simple, makes use of small glass vials (125 mℓ-volume were used in this research) which do not require any stirring nor feeding device or other engineered tool: a serum bottle is sealed immediately after all components are poured inside and thereafter conducted in a batch mode and occasionally shaken to ensure adequate homogenisation of the components. The only variables which are regularly measured are the volume of biogas produced and gas composition. The two assays, originally developed by Owen et al. (1979) to address the toxicity and the biodegradability have been combined in a single test called AAT, Anaerobic Activity Test, which enables one to assess simultaneously the inhibitory effect on the methanogenic biomass and the biodegradability of the test material as well as the ability of the biomass to adapt to the test material and therefore to overcome the initial inhibition. The screening protocol is illustrated in Annexure A. The protocol consists of a sequence of assays which employ the serum bottle methodology. A first step of the procedure is aimed at rapidly estimating whether the effluent is potentially toxic to the methanogenic biomass and in what concentration. The second step is a more extensive screening, aimed at precisely characterising the toxicity of the effluent, the extent of biodegradation that can be achieved, as well as at establishing whether a potential for adaptation of the biomass exists upon exposure. If the sample passes the screening stage, the same serum bottle method will be used to conduct a series of batch co-digestion experiments aimed at evaluating a convenient volumetric ratio between the test material and the readily biodegradable substrate. Finally, a laboratory-scale codigestion trial could simulate the full-scale process, thus enabling the selection of appropriate operating conditions for the start-up of the full-scale implementation. This the protocol has been used to assess the amenability to be anaerobically (co)digested of four industrial effluents, i.e. size and distillery effluents which are classified as high strength and scour and synthetic dye effluents classified as toxic. From the biodegradability and toxicity assays the following conclusions were drawn. The size and distillery effluent were found to be ii degradable at 32 g COD/ℓ and 16 g COD /ℓ concentrations respectively. Concentrations higher than these stipulated above were found inhibitory. Scour effluent was found to be recalcitrant at all concentration tested and synthetic dye was 100 % degradable at 0.12 g COD/ℓ and lower and highly inhibitory at concentration higher than 1.1 g COD/ℓ. Co-digestion experiment using serum bottle AAT method were undertaken between effluents i.e. size + distillery, size + scour, distillery + synthetic dye in an attempt to verify whether the digestion performance benefits from simultaneous presence of the two substrates. The volumetric ratios between the effluents were 1:1, 1:2, 2:1. The presence of two mixtures in the case of size and distillery had better methane production compared to individual substrate i.e. size or distillery separate. The mixture with volumetric flow rate ratio of 2:1 (size: distillery) was preferable in terms of process performance as it had highest COD removal compared to the other mixtures /ratios and individual substrates. The mixture of size and scour (2:1) had highest degradation percentage compared to other ratios but not high enough to qualify as degradable (less than 50 %). The mixture of distillery and synthetic dye had the same pattern with ratio of 2:1 giving the best COD conversion. The pattern than can be drawn from the degradability of mixtures is: the degradability of mixtures increase with the increasing amount of the most biodegradable compound/effluent in the mixture. Serum bottle results provided the detailed information regarding the safe operating parameters which should be used during the starting point for the larger scale investigation i.e. lab-scale investigations. The lab scale investigations were conducted primarily to validate screening and monitor how the digestion progresses and also to provide data for future project i.e. pilot plant investigation. Other effluents i.e. scour and synthetic dye and their co-digestion mixture were excluded from the lab-scale investigations since they were found to be non- biodegradable i.e. their COD conversion was less the 50 % in the screening protocol. Due to time constrains and other technical difficulties in the laboratory, the co-digestion of size and distillery mixture trials we not conducted on the laboratory scale. Laboratory-scale digestion trials showed that the best organic loading rate for distillery effluent in terms of reactor performance and stability was 1.0g COD/ℓ with efficiency of about 45 %, and for size was 2.0g COD/ℓ with an efficiency of 40 %. The efficiencies obtained in both effluents trials could be greatly improved by acclimation; however these results showed that the digestion of these effluents on the bigger scale is possible.

Many industries use, or produce, metal-containing solutions which must be treated for reuse or discharge to sewer. One such treatment is biological and both living and dead materials have been investigated for the abstraction of metal ions from solution. Studies on systems containing only a single biosorbent are well documented, and mostly involve optimisation of biosorption capacities and metal uptake rates through modification of Biological Support Particle (BSP) size and surface characteristics. Literature on dual biosorbent studies is sparse. The commercial application of biosorption technology in wastewater treatment remains largely unexplored and unexploited. The primary objective here was to assess the potential of forced-upflow packed-bed bioreactors, containing dual biological sorbents, for treating a synthetic wastewater containing copper, zinc and cadmium, at both laboratory- and pilotscale. Pine bark was selected as BSP since it is an abundant, relatively cheap, agricultural waste product in South Africa, and is known to sorb metal ions. Initial experiments aimed to optimise biofilm development on the pine bark surfaces, since microbial biomass is also known to sequester metal ions. Systems comprising either one, or both, these biosorbents were compared for their efficiency in metal removal. The effects of type, size, and state of decomposition, of the pine bark, the addition of supplementary nutrients (Voermolas) and the mixing conditions, on the metal biosorption capacity and reaction kinetics of the systems were also studied. All experiments were conducted at an initial metal concentration of 100mg.ℓ⁻¹with both composted and uncomposted pine bark as BSP. The former supported microbial colonisation and resisted biofilm sloughing, but degraded rapidly causing engineering difficulties. Uncomposted pine bark showed the same ability, but was also physically more robust. Organic compounds leached from the pine bark did not hinder microbial colonisation of the BSP; rather they served as additional nutrients. Literature studies suggest that these compounds would not significantly compromise the COD or increase the toxicity of the final effluent. Biofilms developed without supplementary nutrients, but Cd²⁺ and Zn²⁺ were sorbed more effectively in bioreactors containing Voermolas (39% and 38% Cd²⁺ removal, 36% and 32% Zn²⁺ removal, in 0.2% and 0.1% Voermolas solutions respectively) than in unsupplemented systems (25% Cd²⁺ removal and 20% Zn²⁺ removal). Conversely, Cu²⁺ was removed most efficiently in the absence of supplementary nutrients. Based on biosorption of the target metal ions, 0.1% (v/v) Voermolas was the most effective concentration of supplementary nutrients. Raw, un-colonised pine bark nuggets (16-24mm), and plastic bioballs (commercially available, bespoke BSP), were compared in laboratory-scale bioreactors by measuring the decrease in residual metal ion concentrations over time, and changes in the solution pH. These experiments showed that the two BSPs did not differ significantly in their performance as a support matrix, or as a metal sorbent (30.6% and 32.6% of metal ion remained in solution when using bioballs and pine bark respectively). However, the presence of a biofilm on both these BSPs, improved the overall performance of the bioreactors significantly (for the bioball BSP, residual metal ion levels decreased from 30.6%, in the absence of a biofilm, to 11.0% with a biofilm present. Similarly, for the pine bark BSP, residual metal ion levels decreased from 32.6%, in the absence of a biofilm, to 7.3% with a biofilm present). A cost comparison of the two BSPs showed that raw pine bark nuggets were available at less than 0.1% of the cost of the bioballs. At pilot-scale, modelled kinetic data compared poorly with experimentally determined results, but minimum residual metal concentrations for Cu (1.7mg.ℓ⁻¹) and Zn (4.2 mg.ℓ⁻¹) were below South African (eThekwini Municipality) regulatory limits for discharge to sewer (5mg,ℓ⁻¹ for both), and sea outfall (3mg.ℓ⁻¹ Cu and 20mg.ℓ⁻¹ Zn). However, for Cd the final residual metal concentration (5.6mg.ℓ⁻¹) was above the regulatory discharge threshold for any receiving system. Although some of the effluents from the system investigated could not be legally released into the municipal sewer system without further remediation, the study showed that a system combining living and dead biomass in a single reactor is capable of significantly reducing dissolved metal concentrations in synthetic wastewaters without temperature or pH adjustment. Furthermore, such a system can operate at pilot-scale, where a pine bark matrix represents a significant cost saving over conventional plastic BSPs. / Thesis (Ph.D.)-University of KwaZulu-Natal, Pietermaritzburg, 2013.

A final cover on a waste impoundment is the main physical barrier between the waste impoundment and the environment designed to protect against physical, chemical and biological factors isolating the waste from the atmospheric environment. Since the early 1990‟s regulators in the United States have started accepting vegetation covers in lieu of the prescriptive covers. Currently in South Africa, data that provide field performance comparisons of alternative vegetation covers are few or non-existent; hence a research program was undertaken by an industrial corporation in South Africa to determine the potential use of vegetation covers. In proposing a practical way forward, the Company (AECI Limited) reached an understanding with the Regulators that a vegetated evapotranspiration (ET) cover, would be acceptable provided that its performance in limiting surface water infiltration (and subsequent leaching) could be quantitatively demonstrated. The overall object of this research was to determine the capability of vegetation cover to limit effluent leaching from a waste impoundment. Analysis of the following sub-objectives were required to address and give answers to this study (1) determine, as accurately as possible a climatic water balance on the vegetation covers, (2) determine the geohydrological properties of the material of the waste impoundment, (3) determine the fate of the water i.e. proportion reused via evapotranspiration as opposed to the proportion infiltrating the waste body beneath the root zone and (4) determine the leaching potential below the waste. The study identifies and evaluates the climatic (above ground) and geohydrological (sub-surface) parameters used to estimate the water balance of the materials for a waste impoundment. The study then utilizes these parameters at the respective sites in a finite-element model, called the HYDRUS-2D model, to simulate the water balance of the material. The simulated water balance results were then compared against collected field data, which provide the evidence of the efficiency of a vegetation cover to limit effluent from the impoundment. / Thesis (M.Sc.)-University of KwaZulu-Natal, Pietermaritzburg, 2009.

No description available.

No description available.

The study investigated solid waste management in the Mafikeng Municipality including the attitudes of the residents towards the waste management services rendered by the municipality. The study found the followings: the main sources of waste were from households due to minimal industrial activity in the area; that the residents had negative attitudes and perceptions about the waste management services provided by the Municipality. The majority of residents were not involved in the identification of needs and management of solid waste. They wanted to take an active role in the planning, design and implementation of the service especially where the formulation of policies are concerned; adequate policy mechanisms need to be adopted to enforce proper behaviour in waste disposal. The study recommends that: • the community be involved in planning, design and implementation of the service especially where the formulation of policies are concerned. • adequate policy mechanisms need to be adopted to enforce proper behaviour in waste disposal. / Thesis (MBA) North-West University, Mafikeng Campus, 2003