The introduction of this thesis describes the methods for programming CNC machines and their usage in the industry. The next section compares the CNC machine control systems, general programming principles and the current use of shop-oriented programming WOP (workshop oriented programming) machining. Then the thesis describes a TMV 510CII machine and its operation, setting, practical advices and examples of the Fanuc Guide-i control system by Fanuc company. In the final part a practical demonstration of the CNC machining program for the production of the sample parts on the above machine is given.

The thesis is focused on making the most efficient actuator shaft, using machinery company. Using Fanuc's control system on all machines with examples of their use in practice. Production and integration of a special holder for the drill stage.

<p>Examensarbetet som beskrivs i denna rapport handlar om byte av styrsystem i en CNC-svarv på företaget Precisionsdetaljer Mekatronik i Linköping. Ett Fanuc 5 styrsystem har ersatts av ett modernare Fanuc 21i-styrsystem. Rapporten beskriver det nya styrsystemet och redovisar hur arbetet med att praktiskt byta system har gått till. Arbetet indelades i tre delar, informationssökning, praktiskt arbete och dokumentation. Informationssökningen behövdes både för hopkoppling av de olika delarna och för parameter- och ladderprogrammering. Det praktiska arbetet bestod i att koppla tillsammans de delar som fanns beställda och de delar som skulle tas från det gamla styrsystemet. Dokumentationen ska finnas för framtida bruk, då service och utveckling av systemet ska ske. </p> / <p>This examination work describes changing of a control system in a CNC-lathe. The work has been done at Precisionsdetaljer Mekatronik AB in Linköping, a company with eight to nine employees. One Fanuc 5 control system has been replaced by a modern Fanuc 21i-system. This report describes the new control system and how the practical work has been done. The work has been divided into three parts, information searching, practical work and documentation. Information searching is needed for how to connect the different parts and for parameter-and ladder programming. The practical work consisted of connecting the new parts that were ordered and the parts that should be used from the old control system. The documentation may be used in the future, when service and development of the system will be done.</p>

Examensarbetet som beskrivs i denna rapport handlar om byte av styrsystem i en CNC-svarv på företaget Precisionsdetaljer Mekatronik i Linköping. Ett Fanuc 5 styrsystem har ersatts av ett modernare Fanuc 21i-styrsystem. Rapporten beskriver det nya styrsystemet och redovisar hur arbetet med att praktiskt byta system har gått till. Arbetet indelades i tre delar, informationssökning, praktiskt arbete och dokumentation. Informationssökningen behövdes både för hopkoppling av de olika delarna och för parameter- och ladderprogrammering. Det praktiska arbetet bestod i att koppla tillsammans de delar som fanns beställda och de delar som skulle tas från det gamla styrsystemet. Dokumentationen ska finnas för framtida bruk, då service och utveckling av systemet ska ske. / This examination work describes changing of a control system in a CNC-lathe. The work has been done at Precisionsdetaljer Mekatronik AB in Linköping, a company with eight to nine employees. One Fanuc 5 control system has been replaced by a modern Fanuc 21i-system. This report describes the new control system and how the practical work has been done. The work has been divided into three parts, information searching, practical work and documentation. Information searching is needed for how to connect the different parts and for parameter-and ladder programming. The practical work consisted of connecting the new parts that were ordered and the parts that should be used from the old control system. The documentation may be used in the future, when service and development of the system will be done.

This thesis addresses the problematics of automated mini-doses application of the adhesive. In thesis are summarized the parameters and types of adhesives with regard to the suitability and the basic theory of bonding. At the same time are summarized the available technologies and methods of bonding. Part of the work is the analysis of requirements for automatic microdosing, in terms of management, delivery system, manipulator, mechanics, functional safety. It also includes the selection of suitable components. The thesis contains the development and description of the control software, visualization, data acquisition, management of robotic manipulator, functional safety logics and dispenser management. The outcome of the thesis is a functional device according to the proposed 3D model made of borrowed components on which algorithms are tested and functionality was verified. In the conclusions are described the complementary features ensuring the possibility of setting the device up in the industry.

The diploma thesis is focused on the use of parametric programming family of workpieces. The practical part includes the design of production technology and the creation of a parametric programs for the production of a given group of workpieces using a workpiece measuring probe. The use of common and system variables can be applied to the toolpath programming and the measurement of workpiece offsets, workpieces and machined areas by a workpiece probe and for measuring and checking tools using a tool probe. Measured values can be used in conditional programming to increase the level of automation of the manufacturing process.

The aim of this thesis is to design a robotic cell with two welding robots and rotary table in two designs and to compare different types of control. These designed alternatives evaluate possibly using of its parts. These designed variants compare physically and financially.