Piezoelectric materials find use as actuators and sensors in automotive, aerospace and other related industries. Automotive applications such as fuel injection nozzles and engine health monitoring systems require operating temperatures as high as 300-500 oC. The commercially used piezoelectric material PbZr1-xTixO3 (PZT) is limited to operating temperatures as low as 200 oC due to the temperature induced depolarization effects. PZT, in the undoped state exhibits a piezoelectric coefficient (d33) of 223 pC/N and ferroelectric-paraelectric transition temperature (Tc) of 386 oC. The enhanced properties of PZT occur at a region between the tetragonal and rhombohedral phases, called the Morphotropic Phase Boundary (MPB). Therefore, search for new materials with higher thermal stability and better sensing capabilities were focused on systems that exhibit a PZT-like MPB. This led to the discovery of (x)BiScO3-(1-x)PbTiO3 (BSPT), which exhibits an MPB with enhanced Tc (450 oC) and exceptionally high piezoelectric response (d33 = 460 pC/N). Theoretical studies have shown that the mechanism of enhanced piezoresponse in ferroelectric systems is related to the anisotropic flattening of the free energy profiles. An alternative view point attributes the anomalous piezoelectric response to the presence of high density of low energy domain walls near an inter-ferroelectric transition. Diffraction is a versatile tool to study the structural and microstructural changes of ferroelectric systems upon application of electric field. However, characterization of electric field induced structural and microstructural changes is not a trivial task, since in situ electric field dependent diffraction studies almost invariably give diffraction patterns laden with strong preferred orientation effects, due to the tendency of the ferroelectric/ferroelastic domains to align along the field direction. Additionally, diffraction profiles of MPB compositions exhibit severe overlap of Bragg peaks of the coexisting phases, and hence, it is difficult to ascertain with certainty, if the alteration in the intensity profiles upon application of electric field is due to change in phase fraction of the coexisting phases or due to preferred orientation induced in the different phases by the electric field. The characterization of electric field induced phase transformation in MPB systems, has therefore eluded researchers and has been considered of secondary importance, presumably due to the difficulties in unambiguously establishing the structural changes upon application of electric field. In fact, majority of the in situ electric field dependent diffraction studies have been carried out on compositions just outside the MPB range, i.e. on single phase compositions. In such studies, the focus has been mainly on explaining the piezoelectric response in terms of motions of the non-180° domain walls and field induced lattice strains. In this dissertation, the BSPT system has been systematically investigated with the view to understand the role of different contributing factors to the anomalous piezoelectric response of compositions close to the MPB. Using a comparative in situ electric field dependent diffraction study on a core MPB composition exhibiting highest piezoelectric response and a single phase monoclinic (pseudo-rhombohedral) composition just outside the MPB, it is demonstrated that, inspite of the significantly large domain switching and lattice strain (obtained from peak shifts) in the single phase composition, as compared to the MPB composition, the single phase composition shows considerably low piezoelectric response. This result clearly revealed that the anomalous piezoelectric response of the MPB composition is primarily associated with field induced inter-ferroelectric transformation and the corresponding field induced interphase boundary motion. A simple strategy has been employed to establish the field induced structural transformation for the MPB compositions, by overcoming the experimental limitation of in situ electric field dependent diffraction studies. The idea stemmed from the fact that, if the specimens for diffraction study can be used in powder form instead of pellet, the problems associated with preferred orientation effects can be eliminated, and the nature of field induced structural changes can be accurately determined. A comparative study of the diffraction profiles from poled (after subjecting the specimen to electric field) and unpoled (before subjecting the specimen to electric field) powders could precisely establish the nature of electric field induced phase transformation for the MPB compositions of BSPT and provided a direct correlation between the electric field induced structural changes and the enhanced piezoelectric response. A new ‘powder poling’ technique was devised, which involves application of electric field to powder form of the specimen. Using this technique, it was possible to study separately, the effect of stress and electric field on the nature of structural transformation. A unique outcome of this study was, it could demonstrate for the first time, analogous nature of the stress and electric field induced structural transformation. A comparative study of the dielectric response of poled and unpoled samples was used to show a counterintuitive phenomenon of field induced decrease in polarization coherence for the MPB compositions. This approach was used to suggest that the criticality associated with the MPB extends beyond the composition boundary conventionally reported in literature based on bulk diffraction techniques (x-ray and neutron powder diffraction). The layout of the dissertation is as follows: Chapter 1 gives a brief introduction of the fundamental concepts related to ferroelectric materials. The theories that explain the enhanced piezoresponse of MPB based ferroelectric systems have been outlined. Detailed information of the existing literature is presented in the relevant chapters. Chapter 2 presents the details of the solid state synthesis of BSPT compositions and structural analysis using diffraction studies. The dielectric measurements were used to establish the Tc for the different compositions. The enhanced ferroelectric and piezoelectric properties were observed for the MPB compositions, which were shown to exhibit coexistence of tetragonal and monoclinic phases from structural studies. The critical MPB composition exhibiting highest piezoelectric and ferroelectric properties was established to be x = 0.3725. The thermal stability of the critical MPB composition was established to be 400 oC using ex situ thermal depolarization studies. The common approach of structural analysis in the unpoled state failed to provide a unique relationship between the anomalous piezoelectric response and the structural factors at the MPB, emphasizing the need to characterize these system using electric field dependent structural studies. Chapter 3 presents the results of in situ electric field dependent diffraction measurements carried out at Argonne National Laboratory, USA. The quasi-static field measurements could successfully quantify the non-180o domain switching fractions and the field induced lattice strains. The changes in the integrated intensities were used to obtain the non-180o domain switching fraction and the shift in peak positions were used to quantify the field induced lattice strains. The in situ studies could successfully explain the macroscopic strain response for the single phase pseudo-rhombohedral (monoclinic) composition on the basis of domain switching mechanisms and field induced lattice strains. The MPB compositions were shown to have additional contributions from interphase boundary motion, resulting from change in phase fraction of the coexisting phases. The results emphasized the need to investigate the electric field induced transformation for MPB compositions, in order to give a comprehensive picture of the various contributions to the macroscopic piezoreponse. While Rietveld analysis could be used to investigate the phase transformation behaviour upon application of electric field, textured diffraction profiles obtained using in situ studies, in addition to the severely overlapping Bragg reflections of the coexisting phases for the MPB compositions hindered reliable estimation of the structural parameters. An alternate approach to investigate the field induced phase transformation is presented in Chapter 4. The stroboscopic measurements on the MPB composition showed evidence of non-180o domain wall motion even at sub-coercive field amplitudes as low as 0.1 kV/mm. Chapter 4 presents the results of the ex situ electric field dependent structural study, wherein the diffraction profiles collected from poled powders is compared to that of unpoled powders. The diffraction profiles from the poled powders did not exhibit any field induced crystallographic texture and could successfully be analyzed using Rietveld analysis. High resolution synchrotron diffraction studies (ESRF, France) carried out on closely spaced compositions revealed that, the composition exhibiting the highest piezoelectric response is the one, which exhibits significantly enhanced lattice polarizability of both the coexisting (monoclinic and tetragonal) phases. The enhanced lattice polarizability manifests as significant fraction of the monoclinic phase transforming irreversibly to the tetragonal phase after electric poling. The monoclinic to tetragonal transformation suggested the existence of a low energy polarization rotation pathway towards the [001]pc direction in the (1 1 0)pc pseudocubic plane of the monoclinic phase. The results are discussed on the basis of the existing theories that explain piezoresponse in MPB systems and are in support of the Polarization rotation model, in favor of a genuine monoclinic phase. Chapter 5 discusses the ferroelectric-ferroelectric stability of the MPB compositions in response to externally applied stress and electric field independently. Using the newly developed ‘powder poling’ technique, which is based on the concept of exploiting the irreversible structural changes that occur after application of electric field and stress independently, it was possible to ascertain that, both moderate stress and electric field induce identical structural transformation - a fraction of the monoclinic phase transforms irreversibly to the tetragonal phase. The powder poling technique was also used to demonstrate field induced inter-ferroelectric transformation at sub-coercive field amplitudes. In addition, the analysis of the dielectric response before and after poling revealed a counterintuitive phenomenon of poling induced decrease in the spatial coherence of polarization for compositions around the MPB and not so for compositions far away from the MPB range. Exploiting the greater sensitivity of this technique, it was demonstrated that, the criticality associated with the inter-ferroelectric transition spans a wider composition range than what is conventionally reported in the literature based on bulk x-ray/neutron powder diffraction techniques. Chapter 6 presents the closure and important conclusions from the present work and summarizes the key results, highlighting the proposed mechanism of enhanced piezoresponse in BSPT. The last part of the chapter deals with suggestions for future work from the ideas evolved in the present study. vi

The temperature and/or entropy of electrically polarisable materials can be altered by changing electric field E. Research into this electrocaloric (EC) effect has focussed on increasing the size of the EC effects, with the long-term aim of building a cooler with an EC material at its heart. Materials and experimental methods are briefly reviewed. A ‘resetting’ indirect route to isothermal entropy change ∆S for hysteretic first-order transitions is described. An indirect route to adiabatic temperature change ∆T, without the need for field-resolved heat capacity data, is also described. Three temperature controllers were built: a cryogenic probe for 77-420 K with ∼5 mK resolution, a high-temperature stage with vacuum enclosure for 295-700 K with ∼15 mK resolution, and a low-temperature stage for 120-400 K with electrical access via micropositioners. Automation enables dense datasets to be compiled. Single crystals of inorganic salts (NH4)2SO4 , KNO3 and NaNO2 were obtained. Applying 380 kV cm−1 across (NH4)2SO4 , it was found that |∆S| ∼ 20 J K−1 kg−1 and |∆T | ∼ 4 K, using the indirect method near the Curie temperature TC = 223 K. Without the ‘resetting’ indirect method, |∆S| ∼ 45 J K−1 kg−1 would have been spuriously found. Preliminary indirect measurements on KNO3 and NaNO2 give |∆S| ∼ 75 J K−1 kg−1 for ∆E ∼ 31 kV cm−1 near TC = 400 K and |∆S| ∼ 14 J K−1 kg−1 for ∆E ∼ 15 kV cm−1 near TC = 435 K, respectively. A cation-ordered PbSc0.5Ta0.5O3 ceramic showing a nominally first-order transition at 295 K was obtained. The Clausius-Clapeyron phase diagram is revealed via indirect measurements where |∆S| ∼ 3.25 J K−1 kg−1 and |∆T | ∼ 2 K, and direct measurements where |∆T | ∼ 2 K. Clamped samples show broadening of the field-induced transition. Epitaxial, ∼64 nm-thick SrTiO3 films were grown by pulsed laser deposition on NdGaO3 (001) substrates with a La0.67Sr0.33MnO3 bottom electrode. The indirect method gives |∆S| ∼ 8 J K−1 kg−1 and |∆T | ∼ 3.5 K near 180 K with |∆E| = 780 kV cm−1. Finite element modelling (FEM) was used to optimise the geometry of multilayered capacitors (MLCs) for EC cooling. Intrinsic cooling powers of 25.9 kW kg−1 are predicted for an optimised MLC based on PVDF-TrFE with Ag electrodes.

Ferroelectric materials are very promising for a variety of applications such as high-permittivity capacitors, ferroelectric memories, pyroelctric sensors, piezoelectric and electrostrictive transducers and electro-optic devices, etc. In the area of ferroelectric ceramics, lead-based compounds, which include lead zirconatetitanate (PZT) solid solutions, occupy an important place because of their superior physical properties. However, due to the toxicity of lead, there is an increasing concern over recycling and disposing of the devices made out of these compounds, which has compelled the researchers around the globe to search for lead-free compounds with promising piezo and ferroelectric properties. Ferroelectric materials that belong to Aurivillius family of oxides have become increasingly important from the perspective of industrial applications because of their high Curie-temperatures, high resistivity, superior polarization fatigue resistanceand stable piezoelectric properties at high temperatures. These bismuth layer-structured ferroelectrics (BLSF) comprise an intergrowth of [Bi2O2]2+ layers and [An+1Bn O3n+1]2- pseudo-perovskite units, where ‘n’ represents the number of perovskite-like layers stacked along the c-axis. ‘A’ stands for a mono-, di- or trivalent ions or a combination of them, ‘B’ represents a small ion with high valencysuch as Ti4+, Nb5+, Ta5+or a combination of them.Ferroelectricity in the orthorhombic phase of these compounds was generally attributed to the cationic displacement along the polar a-axis and the tilting of octahedra around the a- and c-axes. Sr2Bi4Ti5O18(SBT) is ann = 5 member of the Aurivillius family and possess promising ferroelectric and piezoelectric properties that could be exploited for a wide range of applications, including ferroelectric random access memories (FeRAM), piezoelectric actuators, transducers and transformers. Reports in the literaturereveal that the ferroelectricand piezoelectric properties of these oxides can be tuned depending on synthesis routes vis-a-vis micro-structural aspects (texture, grain size) and site specific dopant substitutions.In the present study, textured SBT ceramics were fabricated using pre-reacted precursors and their anisotropic dielectric, piezoelectric and ferroelectric properties were demonstrated. Grain size tunability with regard to their physical properties was accomplished in the ceramics, fabricated using fine powders obtained from citrate assisted sol-gel synthesis. The grain size dependent second harmonic generation activity of SBT ceramics was investigated. Enhancement in the piezoelectric and ferroelectric properties of SBT ceramics was achieved by substituting A site ions (Sr2+) with a combination of Na+ and Bi3+. From the perspective of non-linear optical device applications, physical properties associated with the SBT crystallized in a transparent lithium borate glass matrix were studied. The results obtained in the present investigations are organized as follows, Chapter 1 gives a brief exposure to the field of ferroelectrics. The emphasis has been on the ferroelectric oxides belonging to the Aurivillius family. Structural aspects and the underlying phenomena associated with ferroelectricity in these compounds are discussed. A brief introduction to the glasses, thermodynamic aspects of glass formation and fabrication of glass- ceramics are included. Basic principles involved in the non-linear optical activities are highlighted. Chapter 2 describes the various experimental techniques that were employed to synthesize and characterize the materials under investigation. The experimental details pertaining to the measurement of various physical properties are included. Chapter 3 deals with the fabrication of Sr2Bi4Ti5O18 ceramics using the pre-reacted Bi4Ti3O12 and SrTiO3 powders viasolid-state reaction route. These in stoichiometric ratio were uniaxially pressed and sintered at 1130oC for 3 h resulting in textured Sr2Bi4Ti5O18 ceramics. The obtained dense ceramics exhibited crystallographic anisotropy with prominent c-axis oriented grains (Lotgering factor of 0.62) parallel to the uniaxially pressed direction. The resultant anisotropy in the ceramics was attributed to the reactive template-like behavior of Bi4Ti3O12 that was used as a precursor to fabricate Sr2Bi4Ti5O18 ceramics. Dielectric, ferro and piezoelectric properties measured on the ceramics in the direction perpendicular to the uniaxially pressed axis were found to be superior to that measured in the parallel direction. Chapter 4 reports the details pertaining to the synthesis of strontium bismuth titanate (Sr2Bi4Ti5O18) powders comprising crystallites of average sizes in the range of 94–1400 nm via citrate-assisted sol-gel route. X-ray powder diffraction, Transmission Electron Microscopy (TEM) and Raman spectroscopy were employed for the structural studies. A crystallite size-dependent variation in the lattice parameters and the shift in the Raman vibration modes were observed. Second harmonic signal (532 nm) intensity of the Sr2Bi4Ti5O18 powders increased with the increase in the average crystallite size and the maximum intensity obtained in the reflection mode was 1.4 times as high as that of the powdered KH2PO4. Piezo force microscopic analyses carried out on an isolated crystallite of size 74 nm, established its single domain nature with the coercive field as high as 347 kV/cm. There was a systematic increase in the d33 value with an increase in the size of the crystallite and a high piezoelectric coefficient of ~27 pm/V was obtained from an isolated crystallite of size 480 nm. Chapter 5 illustrates the details concerning the fabrication of Sr2Bi4Ti5O18(SBT) ceramics with different grain sizes (93 nm–1.42 μm) using nano-crystalline powders synthesized via citrate assisted sol-gel method. The grain growth in these powder compacts was found to be controlled via the grain boundary curvature mechanism, associated with anactivation energy of 181.9 kJ/mol. Interestingly with a decrease in grain size there was an increase in the structural distortion which resulted in a shift of Curie-temperature (phase transition) towards higher temperatures than that of conventional bulk ceramics. Extended Landau phenomenological theory for the ferroelectric particles was invoked to explain experimentally observed size dependent phase transition temperature and the critical size for SBT is predicted to be 11.3 nm. Grain size dependent dielectric, ferroelectric and piezoelectric properties of the SBT ceramics were studied and the samples comprising average grain size of 645 nm exhibited superior physical properties that include remnant polarization (2Pr) = 16.4 μC cm-2, coercive field (Ec) = 38 kV cm-1, piezoelectric coefficient (d33) = 22 pC N-1 and planar electromechanical coupling coefficient (kp) = 14.8 %. In Chapter 6, the studies pertaining to the fabrication of Sr(2-x)(Na0.5Bi0.5)xBi4Ti5O18 (SNBT) ceramics for various x values (0, 0.1, 0.25, 0.3, 0.4 and 0.5), using fine powders synthesized via sol-gel route are dealt with. X-ray powder diffraction, transmission electron microscopy and Raman spectroscopic studies were carried out to confirm composition dependent structural changes taking place in the SNBT ceramics. Scanning electron microscopic studies carried out on ceramics revealed that dopants played an important role in inhibiting the grain growth. Dielectric constants of the ceramics were found to decrease with an increase in ‘x’. The increase in Curie temperature with increase in ‘x’ is attributed to the decrease in the tolerance factor. Particularly,x = 0.3 composition of the SNBT ceramics exhibited better piezo and ferroelectric properties with a higher Curie-temperature (569 K). The piezoelectric coefficient (d33) and the planar electromechanical coupling coefficient (kp) of SNBT(x = 0.3) were enhanced by 25% and 42% respectively as compared to that of the undoped ceramics. Chapter 7 deals with the glasses in the system (100 –x) {Li2O + 2B2O3} ─x {2SrO + 2Bi2O3 +5TiO2} (where, x = 10, 25 and 35) fabricated via conventional melt-quenching technique. The amorphous and glassy characteristics of the samples were confirmed respectively using X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods. All the compositions under investigation exhibited two distinct crystallization peaks (exothermic peaks in the DSC traces): the first peak at ~ 545 °C and the second at ~610 °C that were found to be associated with the crystallization of the phases (as confirmed from the XRD studies) Sr2Bi4Ti5O18 (SBT)and Li2B4O7 (LBO) respectively. Non-isothermal crystallization kinetics (using modified Ozawa-type plots) for SBT crystallization in the LBO glass matrix for the compositions x = 10 and 35, indicated three dimensional growth of the crystallites from pre-existing nuclei present in the as-quenched samples and their effective activation energies for crystallization were found to be around 686 ± 85 kJ/mol and 365 ± 53 kJ/mol, respectively. The optical band gap of the as-quenched glasses for the composition x = 35 was 2.52 eV, is less than that of the composition x = 10 (2.91 eV). The Urbach energies for the as-quenched glasses of compositions x = 10, 25 and 35 were found to be 118 ± 2 meV, 119 ± 2 meV and 192 ± 1 meV respectively.The glasses associated with the composition x = 35, on controlled heat-treatment at 515 °C for various durations (1―20 h), yielded glass-ceramics comprising SBT nano-crystals (18―28 nm) embedded in the LBO glass matrix. Compressive strain in the nano-crystallites of SBT, analyzed using Williamson-Hall method was found to decrease with an increase in the crystallite size. The second harmonic generation signal (532 nm) intensity emanating from glass-nanocrystal composites comprising 22.1 nm SBT crystallites was nearly 0.3 times that of a KDP single crystal. Although each chapter is provided with conclusions and a list of references, thesis ends with a separate summary and conclusions.